Yixun Lan <[email protected]> writes:
> From: Xingyu Chen <[email protected]>
>
> Add new pinctrl DT info for the Amlogic's Meson-AXG SoC.
>
> Reviewed-by: Neil Armstrong <[email protected]>
> Signed-off-by: Xingyu Chen <[email protected]>
> Signed-off-by: Yixun Lan <[email protected]>
> ---
> arch/arm64/boot/dts/amlogic/meson-axg.dtsi | 44
> ++++++++++++++++++++++++++++++
> 1 file changed, 44 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/amlogic/meson-axg.dtsi
> b/arch/arm64/boot/dts/amlogic/meson-axg.dtsi
> index 5fc33b76b91c..e0fb860e12c5 100644
> --- a/arch/arm64/boot/dts/amlogic/meson-axg.dtsi
> +++ b/arch/arm64/boot/dts/amlogic/meson-axg.dtsi
> @@ -9,6 +9,7 @@
> #include <dt-bindings/interrupt-controller/arm-gic.h>
> #include <dt-bindings/clock/axg-clkc.h>
> #include <dt-bindings/clock/axg-aoclkc.h>
This doesn't apply because this aoclkc.h header does not exist in
mainline.
Kevin
> +#include <dt-bindings/gpio/meson-axg-gpio.h>
>
> / {
> compatible = "amlogic,meson-axg";
> @@ -173,6 +174,32 @@
> #mbox-cells = <1>;
> };
>
> + periphs: periphs@ff634000 {
> + compatible = "simple-bus";
> + reg = <0x0 0xff634000 0x0 0x2000>;
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges = <0x0 0x0 0x0 0xff634000 0x0 0x2000>;
> +
> + pinctrl_periphs: pinctrl@480 {
> + compatible =
> "amlogic,meson-axg-periphs-pinctrl";
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges;
> +
> + gpio: bank@480 {
> + reg = <0x0 0x00480 0x0 0x40>,
> + <0x0 0x004e8 0x0 0x14>,
> + <0x0 0x00520 0x0 0x14>,
> + <0x0 0x00430 0x0 0x3c>;
> + reg-names = "mux", "pull",
> "pull-enable", "gpio";
> + gpio-controller;
> + #gpio-cells = <2>;
> + gpio-ranges = <&pinctrl_periphs 0 0 86>;
> + };
> + };
> + };
> +
> sram: sram@fffc0000 {
> compatible = "amlogic,meson-axg-sram", "mmio-sram";
> reg = <0x0 0xfffc0000 0x0 0x20000>;
> @@ -209,6 +236,23 @@
> };
> };
>
> + pinctrl_aobus: pinctrl@14 {
> + compatible = "amlogic,meson-axg-aobus-pinctrl";
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges;
> +
> + gpio_ao: bank@14 {
> + reg = <0x0 0x00014 0x0 0x8>,
> + <0x0 0x0002c 0x0 0x4>,
> + <0x0 0x00024 0x0 0x8>;
> + reg-names = "mux", "pull", "gpio";
> + gpio-controller;
> + #gpio-cells = <2>;
> + gpio-ranges = <&pinctrl_aobus 0 0 15>;
> + };
> + };
> +
> uart_AO: serial@3000 {
> compatible = "amlogic,meson-gx-uart",
> "amlogic,meson-ao-uart";
> reg = <0x0 0x3000 0x0 0x18>;
