Hi,
On Wed, 27 Dec 2017 23:47:23 +0200
Sakari Ailus <sakari.ai...@iki.fi> wrote:
> Hi Yong,
>
> On Thu, Dec 21, 2017 at 10:49:35AM +0800, Yong wrote:
> > Hi,
> >
> > On Tue, 19 Dec 2017 13:53:28 +0200
> > Sakari Ailus <sakari.ai...@iki.fi> wrote:
> >
> > > Hi Yong,
> > >
> > > On Thu, Jul 27, 2017 at 01:01:36PM +0800, Yong Deng wrote:
> > > > Add binding documentation for Allwinner V3s CSI.
> > > >
> > > > Signed-off-by: Yong Deng <yong.d...@magewell.com>
> > >
> > > DT bindings should precede the driver.
> >
> > OK.
> >
> > >
> > > > ---
> > > > .../devicetree/bindings/media/sun6i-csi.txt | 49
> > > > ++++++++++++++++++++++
> > > > 1 file changed, 49 insertions(+)
> > > > create mode 100644
> > > > Documentation/devicetree/bindings/media/sun6i-csi.txt
> > > >
> > > > diff --git a/Documentation/devicetree/bindings/media/sun6i-csi.txt
> > > > b/Documentation/devicetree/bindings/media/sun6i-csi.txt
> > > > new file mode 100644
> > > > index 0000000..f8d83f6
> > > > --- /dev/null
> > > > +++ b/Documentation/devicetree/bindings/media/sun6i-csi.txt
> > > > @@ -0,0 +1,49 @@
> > > > +Allwinner V3s Camera Sensor Interface
> > > > +------------------------------
> > > > +
> > > > +Required properties:
> > > > + - compatible: value must be "allwinner,sun8i-v3s-csi"
> > >
> > > What are sun6i and sun8i? Is this device first present in sun6i SoCs,
> > > whereas you have only defined bindings for sun8i?
> >
> > Yes, some sun6i SoCs has the almost same CSI module.
> > There is only V3s on my hand. So, I only tested it on V3s. But
> > some people work on the others.
>
> Ack.
>
> >
> > >
> > > > + - reg: base address and size of the memory-mapped region.
> > > > + - interrupts: interrupt associated to this IP
> > > > + - clocks: phandles to the clocks feeding the CSI
> > > > + * ahb: the CSI interface clock
> > > > + * mod: the CSI module clock
> > > > + * ram: the CSI DRAM clock
> > > > + - clock-names: the clock names mentioned above
> > > > + - resets: phandles to the reset line driving the CSI
> > > > +
> > > > +- ports: A ports node with endpoint definitions as defined in
> > > > + Documentation/devicetree/bindings/media/video-interfaces.txt.
> > >
> > > Please document mandatory and optional endpoint properties relevant for
> > > the
> > > hardware.
> >
> > I have added below commit in my v3:
> > Currently, the driver only support the parallel interface. So, a single port
> > node with one endpoint and parallel bus is supported.
>
> Please specify the exact properties that are relevant for the hardware. No
> references should be made to the driver, the bindings are entirely
> separate.
>
> Are the non-parallel (CSI-2?) and parallel bus on the same interface? If
> yes, they should probably use different endpoints, if not, then different
> ports.
>
> You could document the other bus or omit it now altogether, in which case
> you'd only detail the parallel bus properties here.
Thanks for your explication. I have misunderstood this.
>
> >
> > >
> > > > +
> > > > +Example:
> > > > +
> > > > + csi1: csi@01cb4000 {
> > > > + compatible = "allwinner,sun8i-v3s-csi";
> > > > + reg = <0x01cb4000 0x1000>;
> > > > + interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
> > > > + clocks = <&ccu CLK_BUS_CSI>,
> > > > + <&ccu CLK_CSI1_SCLK>,
> > > > + <&ccu CLK_DRAM_CSI>;
> > > > + clock-names = "ahb", "mod", "ram";
> > > > + resets = <&ccu RST_BUS_CSI>;
> > > > +
> > > > + port {
> > > > + #address-cells = <1>;
> > > > + #size-cells = <0>;
> > > > +
> > > > + /* Parallel bus endpoint */
> > > > + csi1_ep: endpoint {
> > > > + remote-endpoint = <&adv7611_ep>;
> > > > + bus-width = <16>;
> > > > + data-shift = <0>;
> > > > +
> > > > + /* If hsync-active/vsync-active are
> > > > missing,
> > > > + embedded BT.656 sync is used */
> > > > + hsync-active = <0>; /* Active low */
> > > > + vsync-active = <0>; /* Active low */
> > > > + data-active = <1>; /* Active high */
> > > > + pclk-sample = <1>; /* Rising */
> > > > + };
> > > > + };
> > > > + };
> > > > +
> > >
> > > --
> > > Kind regards,
> > >
> > > Sakari Ailus
> > > e-mail: sakari.ai...@iki.fi
> >
> >
> > Thanks,
> > Yong
>
> --
> Regards,
>
> Sakari Ailus
> e-mail: sakari.ai...@iki.fi
Thanks,
Yong
