Hi Mark, > -----Original Message----- > From: Mark Rutland [mailto:mark.rutl...@arm.com] > Sent: Thursday, February 01, 2018 2:33 AM > To: Jolly Shah <jol...@xilinx.com> > Cc: ard.biesheu...@linaro.org; mi...@kernel.org; > gre...@linuxfoundation.org; m...@codeblueprint.co.uk; > sudeep.ho...@arm.com; hkallwe...@gmail.com; keesc...@chromium.org; > dmitry.torok...@gmail.com; michal.si...@xilinx.com; robh...@kernel.org; > linux-arm-ker...@lists.infradead.org; linux-kernel@vger.kernel.org; > devicet...@vger.kernel.org; Rajan Vaja <raj...@xilinx.com> > Subject: Re: [PATCH v3 2/4] drivers: firmware: xilinx: Add ZynqMP firmware > driver > > On Thu, Feb 01, 2018 at 01:23:48AM +0000, Jolly Shah wrote: > > Hi Mark, > > Thanks for the review, > > > > > -----Original Message----- > > > From: Mark Rutland [mailto:mark.rutl...@arm.com] > > > Sent: Wednesday, January 31, 2018 10:20 AM > > > To: Jolly Shah <jol...@xilinx.com> > > > Cc: ard.biesheu...@linaro.org; mi...@kernel.org; > > > gre...@linuxfoundation.org; m...@codeblueprint.co.uk; > > > sudeep.ho...@arm.com; hkallwe...@gmail.com; keesc...@chromium.org; > > > dmitry.torok...@gmail.com; michal.si...@xilinx.com; > > > robh...@kernel.org; linux-arm-ker...@lists.infradead.org; > > > linux-kernel@vger.kernel.org; devicet...@vger.kernel.org; Jolly Shah > > > <jol...@xilinx.com>; Rajan Vaja <raj...@xilinx.com> > > > Subject: Re: [PATCH v3 2/4] drivers: firmware: xilinx: Add ZynqMP > > > firmware driver > > > > > > On Wed, Jan 24, 2018 at 03:21:12PM -0800, Jolly Shah wrote: > > > > This patch is adding communication layer with firmware. > > > > Firmware driver provides an interface to firmware APIs. > > > > Interface APIs can be used by any driver to communicate to > > > > PMUFW(Platform Management Unit). All requests go through ATF. > > > > > > > +/** > > > > + * zynqmp_pm_set_wakeup_source - PM call to specify the wakeup > source > > > > + * while suspended > > > > + * @target: Node ID of the targeted PU or subsystem > > > > + * @wakeup_node:Node ID of the wakeup peripheral > > > > + * @enable: Enable or disable the specified peripheral as wake > source > > > > + * > > > > + * Return: Returns status, either success or error+reason > > > > + */ > > > > +static int zynqmp_pm_set_wakeup_source(const u32 target, > > > > + const u32 wakeup_node, > > > > + const u32 enable) > > > > +{ > > > > + return invoke_pm_fn(PM_SET_WAKEUP_SOURCE, target, > > > > + wakeup_node, enable, 0, NULL); } > > > > > > I see many functions take a "Node ID" parameter, but these don't > > > appear to be in any DT binding, and drivers (other than the debugfs > > > driver) > aren't using them. > > > > > > What's the plan for making use of these? Where are the node IDs > > > going to come from in practice? > > > > > Node ids are defined in firmware.h. Node id refers to targeted > PU/subsystem/peripheral for required action. > > Ok. What I was asking was how a node id would be associated with particular > peripheral instances (which are presumably going to be nodes in the DT). > > e.g. if I have > > device@foo { > compatible = "xlnx,some-device"; > reg = <0xf00 0x100>; > ... > }; > > ... how does the kernel know which node id(s) the device is associated with? > > I assume that those will need something like a xlnx,eemi-node-id property. > > [...] >
ZynqMP Power domain driver has node-ids defines under pd-id properties.(RFC patch below) https://patchwork.kernel.org/patch/10150683/ Individual driver can have phandle to it. For example, power-domains { pd_xx: pd_xx { #power-domain-cells = <0x0>; pd-id = <0x7>; }; pd_yy: pd_yy { #power-domain-cells = <0x0>; pd-id = <0xf>; }; }; device: dev@ffe00000 { compatible = "dev"; reg = <0x0 0xFFE00000 0x0 0x20000>; pd-handle = <&pd_xx>; }; > > > > +/** > > > > + * zynqmp_pm_pinctrl_request - Request Pin from firmware > > > > + * @pin: Pin number to request > > > > + * > > > > > > No DT binding for the pinctrl bits? > > > > > > [...] > > It doesn't require any bindings. Calling drivers will have DT binding for > > pins they > use. > > For those drivers to be able to refer to the EEMI FW as a pin controller, > we'll > need a pinctrl node in the DT (and hence a binding). > This is just an interface driver. There is a separate pinctrl and clock driver who will use these APIs to communicate with PMU(Platform Management Unit). Those driver has required DT nodes and bindings to use these APIs. For example, Clock driver bindings are mentioned below: https://patchwork.kernel.org/patch/10150703/ > > > > +/** > > > > + * zynqmp_pm_clock_enable - Enable the clock for given id > > > > + * @clock_id: ID of the clock to be enabled > > > > + * > > > > > > Likewise for the clocks? > > > > > It doesn't require bindings too. > > As with pinctrl, for drivers to be able to refer to these clocks, we'll need > a clock > node in the DT (and hence a binding). > > Thanks, > Mark.
