On Fri, Mar 02, 2018 at 09:20:40AM +0530, Manivannan Sadhasivam wrote:
> Add gpio nodes for Actions Semi S900 SoC.
> 
> Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasi...@linaro.org>
> ---
>  .../devicetree/bindings/gpio/actions,owl-gpio.txt  | 95 
> ++++++++++++++++++++++
>  1 file changed, 95 insertions(+)
>  create mode 100644 
> Documentation/devicetree/bindings/gpio/actions,owl-gpio.txt
> 
> diff --git a/Documentation/devicetree/bindings/gpio/actions,owl-gpio.txt 
> b/Documentation/devicetree/bindings/gpio/actions,owl-gpio.txt
> new file mode 100644
> index 000000000000..d2939ca6cfaf
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/gpio/actions,owl-gpio.txt
> @@ -0,0 +1,95 @@
> +* Actions Semi OWL GPIO controller bindings
> +
> +The GPIOs are organized as individual banks/ports with variable number
> +of GPIOs. Each bank is represented as an individual GPIO controller.
> +
> +Required properties:
> +- compatible            : Should be "actions,s900-gpio"
> +- reg                   : Address and range of the GPIO controller registers.
> +- gpio-controller       : Marks the device node as a GPIO controller.
> +- #gpio-cells           : Should be <2>. The first cell is the gpio number
> +                          and the second cell is used to specify optional
> +                          parameters.
> +- interrupt-controller  : Marks the device node as an interrupt controller.
> +- #interrupt-cells      : Specifies the number of cells needed to encode an
> +                          interrupt.  Shall be set to 2.  The first cell
> +                          defines the interrupt number, the second encodes
> +                          the trigger flags described in
> +                          bindings/interrupt-controller/interrupts.txt
> +
> +Optional properties:
> +- gpio-ranges           : Mapping between GPIO and pinctrl
> +
> +Note: Each GPIO port should have an alias correctly numbered in "aliases"
> +node.

Why? Please don't use aliases for gpios.

> +
> +Examples:
> +
> +aliases {
> +        gpio0 = &gpioa;
> +        gpio1 = &gpiob;
> +        gpio2 = &gpioc;
> +        gpio3 = &gpiod;
> +        gpio4 = &gpioe;
> +        gpio5 = &gpiof;
> +};
> +
> +       gpioa: gpioa@e01b0000 {

Use generic node names (gpio).

> +               compatible = "actions,s900-gpio";
> +               reg = <0x0 0xe01b0000 0x0 0x1000>;
> +               gpio-controller;
> +               #gpio-cells = <2>;
> +               gpio-ranges = <&pinctrl 0 0 32>;
> +               interrupt-controller;
> +               #interrupt-cells = <2>;
> +       };
> +
> +       gpiob: gpiob@e01b0000 {

Ah, but your are duplicating addresses here which you shouldn't do 
either. These should be all one node if you can avoid overlapping.

> +               compatible = "actions,s900-gpio";
> +               reg = <0x0 0xe01b0000 0x0 0x1000>;
> +               gpio-controller;
> +               #gpio-cells = <2>;
> +               gpio-ranges = <&pinctrl 0 32 32>;
> +               interrupt-controller;
> +               #interrupt-cells = <2>;
> +       };
> +
> +       gpioc: gpioc@e01b0000 {
> +               compatible = "actions,s900-gpio";
> +               reg = <0x0 0xe01b0000 0x0 0x1000>;
> +               gpio-controller;
> +               #gpio-cells = <2>;
> +               gpio-ranges = <&pinctrl 0 64 12>;
> +               interrupt-controller;
> +               #interrupt-cells = <2>;
> +       };
> +
> +       gpiod: gpiod@e01b0000 {
> +               compatible = "actions,s900-gpio";
> +               reg = <0x0 0xe01b0000 0x0 0x1000>;
> +               gpio-controller;
> +               #gpio-cells = <2>;
> +               gpio-ranges = <&pinctrl 0 76 30>;
> +               interrupt-controller;
> +               #interrupt-cells = <2>;
> +       };
> +
> +       gpioe: gpioe@e01b0000 {
> +               compatible = "actions,s900-gpio";
> +               reg = <0x0 0xe01b0000 0x0 0x1000>;
> +               gpio-controller;
> +               #gpio-cells = <2>;
> +               gpio-ranges = <&pinctrl 0 106 32>;
> +               interrupt-controller;
> +               #interrupt-cells = <2>;
> +       };
> +
> +       gpiof: gpiof@e01b0000 {
> +               compatible = "actions,s900-gpio";
> +               reg = <0x0 0xe01b0000 0x0 0x1000>;
> +               gpio-controller;
> +               #gpio-cells = <2>;
> +               gpio-ranges = <&pinctrl 0 138 8>;
> +               interrupt-controller;
> +               #interrupt-cells = <2>;
> +       };
> -- 
> 2.14.1
> 

Reply via email to