This adds support for the Ainol AW1, an A20-based 7" tablet from Ainol.
The following board-specific features are supported:
* LCD panel
* Backlight
* USB OTG
* Buttons
* Touchscreen (doesn't work without non-free firmware)
* Accelerometer
* Battery
The following are untested:
* Audio output
* Audio speakers
* USB via SPCI connector
The following are not supported:
* Wi-Fi
* Bluetooth
* NAND
* Audio via SPCI connector
Signed-off-by: Paul Kocialkowski <cont...@paulk.fr>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/sun7i-a20-ainol-aw1.dts | 358 ++++++++++++++++++++++++++++++
2 files changed, 359 insertions(+)
create mode 100644 arch/arm/boot/dts/sun7i-a20-ainol-aw1.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 9f7133b6fba0..03bfacebfdbd 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -929,6 +929,7 @@ dtb-$(CONFIG_MACH_SUN6I) += \
sun6i-a31s-sinovoip-bpi-m2.dtb \
sun6i-a31s-yones-toptech-bs1078-v2.dtb
dtb-$(CONFIG_MACH_SUN7I) += \
+ sun7i-a20-ainol-aw1.dtb \
sun7i-a20-bananapi.dtb \
sun7i-a20-bananapi-m1-plus.dtb \
sun7i-a20-bananapro.dtb \
diff --git a/arch/arm/boot/dts/sun7i-a20-ainol-aw1.dts
b/arch/arm/boot/dts/sun7i-a20-ainol-aw1.dts
new file mode 100644
index 000000000000..697586991aea
--- /dev/null
+++ b/arch/arm/boot/dts/sun7i-a20-ainol-aw1.dts
@@ -0,0 +1,358 @@
+/*
+ * Copyright 2018 Paul Kocialkowski <cont...@paulk.fr>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun7i-a20.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+ model = "Ainol AW1";
+ compatible = "ainol,ainol-aw1", "allwinner,sun7i-a20";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pinctrl-names = "default";
+ pinctrl-0 = <&backlight_enable_pin>;
+ pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
+ brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
+ default-brightness-level = <5>;
+ enable-gpios = <&pio 7 7 GPIO_ACTIVE_HIGH>; /* PH7 */
+ };
+
+ panel: panel {
+ compatible = "innolux,at070tn92";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-supply = <&panel_power>;
+ backlight = <&backlight>;
+
+ port@0 {
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ panel_input: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&tcon0_out_panel>;
+ };
+ };
+ };
+
+ panel_power: panel_power {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&panel_power_pin>;
+ regulator-name = "panel-power";
+ regulator-min-microvolt = <10400000>;
+ regulator-max-microvolt = <10400000>;
+ gpio = <&pio 7 8 GPIO_ACTIVE_HIGH>; /* PH8 */
+ enable-active-high;
+ regulator-boot-on;
+ };
+};
+
+&codec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&codec_pa_pin>;
+ allwinner,pa-gpios = <&pio 7 15 GPIO_ACTIVE_HIGH>; /* PH15 */
+ status = "okay";
+};
+
+&cpu0 {
+ cpu-supply = <®_dcdc2>;
+};
+
+&de {
+ status = "okay";
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+
+ axp209: pmic@34 {
+ reg = <0x34>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins_a>;
+ status = "okay";
+
+ lis3dh: accelerometer@18 {
+ compatible = "st,lis3dh-accel";
+ reg = <0x18>;
+ vdd-supply = <®_vcc3v3>;
+ vddio-supply = <®_vcc3v3>;
+ st,drdy-int-pin = <1>;
+ };
+};
+
+&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins_a>;
+ status = "okay";
+ clock-frequency = <400000>; /* 400 KHz required for GSL1680. */
+
+ gsl1680: touchscreen@40 {
+ compatible = "silead,gsl1680";
+ reg = <0x40>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&touchscreen_power_pin>;
+ interrupt-parent = <&pio>;
+ interrupts = <7 21 IRQ_TYPE_EDGE_FALLING>; /* EINT21 (PH21) */
+ power-gpios = <&pio 7 20 GPIO_ACTIVE_HIGH>; /* PH20 */
+ firmware-name = "gsl1680-ainol-aw1.fw";
+ touchscreen-size-x = <480>;
+ touchscreen-size-y = <800>;
+ touchscreen-swapped-x-y;
+ touchscreen-inverted-y;
+ silead,max-fingers = <5>;
+ };
+};
+
+&lradc {
+ vref-supply = <®_vcc3v0>;
+ status = "okay";
+
+ button@571 {
+ label = "Volume Up";
+ linux,code = <KEY_VOLUMEUP>;
+ channel = <0>;
+ voltage = <571428>;
+ };
+
+ button@761 {
+ label = "Volume Down";
+ linux,code = <KEY_VOLUMEDOWN>;
+ channel = <0>;
+ voltage = <761904>;
+ };
+
+ button@952 {
+ label = "Home";
+ linux,code = <KEY_HOME>;
+ channel = <0>;
+ voltage = <952380>;
+ };
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
+ cd-inverted;
+ status = "okay";
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&otg_sram {
+ status = "okay";
+};
+
+&pio {
+ panel_power_pin: panel_power_pin@0 {
+ pins = "PH8";
+ function = "gpio_out";
+ };
+
+ backlight_enable_pin: backlight_enable_pin@0 {
+ pins = "PH7";
+ function = "gpio_out";
+ };
+
+ touchscreen_power_pin: touchscreen_power_pin@0 {
+ pins = "PH20";
+ function = "gpio_out";
+ };
+
+ codec_pa_pin: codec_pa_pin@0 {
+ pins = "PH15";
+ function = "gpio_out";
+ };
+
+ usb0_id_detect_pin: usb0_id_detect_pin@0 {
+ pins = "PH4";
+ function = "gpio_in";
+ bias-pull-up;
+ };
+
+ usb0_vbus_pin: usb0_vbus_pin@0 {
+ pins = "PB9";
+ function = "gpio_out";
+ };
+
+ usb1_vbus_pin: usb1_vbus_pin@0 {
+ pins = "PH6";
+ function = "gpio_out";
+ };
+
+ usb2_vbus_pin: usb2_vbus_pin@0 {
+ pins = "PH3";
+ function = "gpio_out";
+ };
+};
+
+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm0_pins_a>;
+ status = "okay";
+};
+
+&tcon0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&lcd_rgb666_pins>;
+ status = "okay";
+};
+
+&tcon0_out {
+ tcon0_out_panel: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&panel_input>;
+ };
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&usb_otg {
+ dr_mode = "otg";
+ status = "okay";
+};
+
+&usbphy {
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb0_id_detect_pin>;
+ usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
+ usb0_vbus_power-supply = <&usb_power_supply>;
+ usb0_vbus-supply = <®_usb0_vbus>;
+ usb1_vbus-supply = <®_usb1_vbus>;
+ usb2_vbus-supply = <®_usb2_vbus>;
+ status = "okay";
+};
+
+#include "axp209.dtsi"
+
+&battery_power_supply {
+ status = "okay";
+};
+
+®_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1450000>;
+ regulator-name = "vdd-cpu";
+};
+
+®_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-int-dll";
+};
+
+®_ldo1 {
+ regulator-name = "vdd-rtc";
+};
+
+®_ldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "avcc";
+};
+
+®_usb0_vbus {
+ pinctrl-0 = <&usb0_vbus_pin>;
+ status = "okay";
+};
+
+®_usb1_vbus {
+ pinctrl-0 = <&usb1_vbus_pin>;
+ status = "okay";
+};
+
+®_usb2_vbus {
+ pinctrl-0 = <&usb2_vbus_pin>;
+ status = "okay";
+};
+
+&usb_power_supply {
+ status = "okay";
+};
--
2.16.3
