Hi Frieder, Thanks for migrating the fsl-quadspi.c driver on the new SPI framework. This patch is using dynamic LUT approach to create the LUT at run time instead of fixed static LUT as being used in current driver present at mtd/spi-nor/fsl-quadspi.c. I have pushed the changes for dynamic LUT on mtd/spi-nor/fsl-quadspi.c and v10 has been in review stage.
Request you to please add 'signed-off' mentioned in those patches in this patch, patchwork link is https://patchwork.ozlabs.org/patch/896534/ Thanks Yogesh Gaur -----Original Message----- From: Frieder Schrempf [mailto:frieder.schre...@exceet.de] Sent: Wednesday, May 30, 2018 6:45 PM To: linux-...@lists.infradead.org; boris.brezil...@bootlin.com; linux-...@vger.kernel.org Cc: dw...@infradead.org; computersforpe...@gmail.com; marek.va...@gmail.com; rich...@nod.at; miquel.ray...@bootlin.com; broo...@kernel.org; David Wolfe <david.wo...@nxp.com>; Fabio Estevam <fabio.este...@nxp.com>; Prabhakar Kushwaha <prabhakar.kushw...@nxp.com>; Yogesh Narayan Gaur <yogeshnarayan.g...@nxp.com>; Han Xu <han...@nxp.com>; Frieder Schrempf <frieder.schre...@exceet.de>; linux-kernel@vger.kernel.org Subject: [PATCH 03/11] spi: Add a driver for the Freescale/NXP QuadSPI controller This driver is derived from the SPI NOR driver at mtd/spi-nor/fsl-quadspi.c. It uses the new SPI memory interface of the SPI framework to issue flash memory operations to up to four connected flash chips (2 buses with 2 CS each). The controller does not support generic SPI messages. Signed-off-by: Frieder Schrempf <frieder.schre...@exceet.de> --- drivers/spi/Kconfig | 11 + drivers/spi/Makefile | 1 + drivers/spi/spi-fsl-qspi.c | 929 ++++++++++++++++++++++++++++++++++++++++ 3 files changed, 941 insertions(+) diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig index e62ac32..6de0df5 100644 --- a/drivers/spi/Kconfig +++ b/drivers/spi/Kconfig @@ -251,6 +251,17 @@ config SPI_FSL_LPSPI help This enables Freescale i.MX LPSPI controllers in master mode. +config SPI_FSL_QSPI + tristate "Freescale QSPI controller" + depends on ARCH_MXC || SOC_LS1021A || ARCH_LAYERSCAPE || COMPILE_TEST + depends on HAS_IOMEM + help + This enables support for the Quad SPI controller in master mode. + Up to four flash chips can be connected on two buses with two + chipselects each. + This controller does not support generic SPI messages. It only + supports the high-level SPI memory interface. + config SPI_GPIO tristate "GPIO-based bitbanging SPI Master" depends on GPIOLIB || COMPILE_TEST diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile index cb1f437..a8f7fda 100644 --- a/drivers/spi/Makefile +++ b/drivers/spi/Makefile @@ -43,6 +43,7 @@ obj-$(CONFIG_SPI_FSL_DSPI) += spi-fsl-dspi.o obj-$(CONFIG_SPI_FSL_LIB) += spi-fsl-lib.o obj-$(CONFIG_SPI_FSL_ESPI) += spi-fsl-espi.o obj-$(CONFIG_SPI_FSL_LPSPI) += spi-fsl-lpspi.o +obj-$(CONFIG_SPI_FSL_QSPI) += spi-fsl-qspi.o obj-$(CONFIG_SPI_FSL_SPI) += spi-fsl-spi.o obj-$(CONFIG_SPI_GPIO) += spi-gpio.o obj-$(CONFIG_SPI_IMG_SPFI) += spi-img-spfi.o diff --git a/drivers/spi/spi-fsl-qspi.c b/drivers/spi/spi-fsl-qspi.c new file mode 100644 index 0000000..c16d070 --- /dev/null +++ b/drivers/spi/spi-fsl-qspi.c @@ -0,0 +1,929 @@ +// SPDX-License-Identifier: GPL-2.0+ + +/* + * Freescale QuadSPI driver. + * + * Copyright (C) 2013 Freescale Semiconductor, Inc. + * Copyright (C) 2018 Bootlin + * Copyright (C) 2018 Exceet Electronics GmbH + * + * Transition to SPI MEM interface: + * Author: + * Boris Brezillion <boris.brezil...@bootlin.com> + * Frieder Schrempf <frieder.schre...@exceet.de> + * + * Based on the original fsl-quadspi.c spi-nor driver: + * Author: Freescale Semiconductor, Inc. + */ + +#include <linux/bitops.h> +#include <linux/clk.h> +#include <linux/completion.h> +#include <linux/delay.h> +#include <linux/err.h> +#include <linux/errno.h> +#include <linux/interrupt.h> +#include <linux/io.h> +#include <linux/jiffies.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/mutex.h> +#include <linux/of.h> +#include <linux/of_device.h> +#include <linux/platform_device.h> +#include <linux/pm_qos.h> +#include <linux/sizes.h> + +#include <linux/spi/spi.h> +#include <linux/spi/spi-mem.h> + +/* + * The driver only uses one single LUT entry, that is updated on + * each call of exec_op(). Index 0 is preset at boot with a basic + * read operation, so let's use the last entry (15). + */ +#define SEQID_LUT 15 + +/* Registers used by the driver */ +#define QUADSPI_MCR 0x00 +#define QUADSPI_MCR_RESERVED_MASK (0xF << 16) +#define QUADSPI_MCR_MDIS_MASK BIT(14) +#define QUADSPI_MCR_CLR_TXF_MASK BIT(11) +#define QUADSPI_MCR_CLR_RXF_MASK BIT(10) +#define QUADSPI_MCR_DDR_EN_MASK BIT(7) +#define QUADSPI_MCR_END_CFG_MASK (0x3 << 2) +#define QUADSPI_MCR_SWRSTHD_MASK BIT(1) +#define QUADSPI_MCR_SWRSTSD_MASK BIT(0) + +#define QUADSPI_IPCR 0x08 +#define QUADSPI_IPCR_SEQID_SHIFT 24 + +#define QUADSPI_BUF3CR 0x1c +#define QUADSPI_BUF3CR_ALLMST_MASK BIT(31) +#define QUADSPI_BUF3CR_ADATSZ_SHIFT 8 +#define QUADSPI_BUF3CR_ADATSZ_MASK (0xFF << QUADSPI_BUF3CR_ADATSZ_SHIFT) + +#define QUADSPI_BFGENCR 0x20 +#define QUADSPI_BFGENCR_SEQID_SHIFT 12 + +#define QUADSPI_BUF0IND 0x30 +#define QUADSPI_BUF1IND 0x34 +#define QUADSPI_BUF2IND 0x38 +#define QUADSPI_SFAR 0x100 + +#define QUADSPI_SMPR 0x108 +#define QUADSPI_SMPR_DDRSMP_MASK (7 << 16) +#define QUADSPI_SMPR_FSDLY_MASK BIT(6) +#define QUADSPI_SMPR_FSPHS_MASK BIT(5) +#define QUADSPI_SMPR_HSENA_MASK BIT(0) + +#define QUADSPI_RBCT 0x110 +#define QUADSPI_RBCT_WMRK_MASK 0x1F +#define QUADSPI_RBCT_RXBRD_USEIPS BIT(8) + +#define QUADSPI_TBDR 0x154 + +#define QUADSPI_SR 0x15c +#define QUADSPI_SR_IP_ACC_MASK BIT(1) +#define QUADSPI_SR_AHB_ACC_MASK BIT(2) + +#define QUADSPI_FR 0x160 +#define QUADSPI_FR_TFF_MASK BIT(0) + +#define QUADSPI_SPTRCLR 0x16c +#define QUADSPI_SPTRCLR_IPPTRC BIT(8) +#define QUADSPI_SPTRCLR_BFPTRC BIT(0) + +#define QUADSPI_SFA1AD 0x180 +#define QUADSPI_SFA2AD 0x184 +#define QUADSPI_SFB1AD 0x188 +#define QUADSPI_SFB2AD 0x18c +#define QUADSPI_RBDR(x) (0x200 + ((x) * 4)) + +#define QUADSPI_LUTKEY 0x300 +#define QUADSPI_LUTKEY_VALUE 0x5AF05AF0 + +#define QUADSPI_LCKCR 0x304 +#define QUADSPI_LCKER_LOCK BIT(0) +#define QUADSPI_LCKER_UNLOCK BIT(1) + +#define QUADSPI_RSER 0x164 +#define QUADSPI_RSER_TFIE BIT(0) + +#define QUADSPI_LUT_BASE 0x310 +#define QUADSPI_LUT_OFFSET (SEQID_LUT * 4 * 4) +#define QUADSPI_LUT_REG(idx) (QUADSPI_LUT_BASE + \ + QUADSPI_LUT_OFFSET + (idx) * 4) + +/* Instruction set for the LUT register */ +#define LUT_STOP 0 +#define LUT_CMD 1 +#define LUT_ADDR 2 +#define LUT_DUMMY 3 +#define LUT_MODE 4 +#define LUT_MODE2 5 +#define LUT_MODE4 6 +#define LUT_FSL_READ 7 +#define LUT_FSL_WRITE 8 +#define LUT_JMP_ON_CS 9 +#define LUT_ADDR_DDR 10 +#define LUT_MODE_DDR 11 +#define LUT_MODE2_DDR 12 +#define LUT_MODE4_DDR 13 +#define LUT_FSL_READ_DDR 14 +#define LUT_FSL_WRITE_DDR 15 +#define LUT_DATA_LEARN 16 + +/* + * The PAD definitions for LUT register. + * + * The pad stands for the number of IO lines [0:3]. + * For example, the quad read needs four IO lines, + * so you should use LUT_PAD(4). + */ +#define LUT_PAD(x) (fls(x) - 1) + +/* + * Macro for constructing the LUT entries with the following + * register layout: + * + * --------------------------------------------------- + * | INSTR1 | PAD1 | OPRND1 | INSTR0 | PAD0 | OPRND0 | + * --------------------------------------------------- + */ +#define LUT_DEF(idx, ins, pad, opr) \ + ((((ins) << 10) | ((pad) << 8) | (opr)) << (((idx) % 2) * 16)) + +/* Controller needs driver to swap endianness */ +#define QUADSPI_QUIRK_SWAP_ENDIAN BIT(0) + +/* Controller needs 4x internal clock */ +#define QUADSPI_QUIRK_4X_INT_CLK BIT(1) + +/* + * TKT253890, the controller needs the driver to fill the txfifo with + * 16 bytes at least to trigger a data transfer, even though the extra + * data won't be transferred. + */ +#define QUADSPI_QUIRK_TKT253890 BIT(2) + +/* TKT245618, the controller cannot wake up from wait mode */ +#define QUADSPI_QUIRK_TKT245618 BIT(3) + +enum fsl_qspi_devtype { + FSL_QUADSPI_VYBRID, + FSL_QUADSPI_IMX6SX, + FSL_QUADSPI_IMX7D, + FSL_QUADSPI_IMX6UL, + FSL_QUADSPI_LS1021A, + FSL_QUADSPI_LS2080A, +}; + +struct fsl_qspi_devtype_data { + enum fsl_qspi_devtype devtype; + unsigned int rxfifo; + unsigned int txfifo; + unsigned int ahb_buf_size; + unsigned int quirks; +}; + +static const struct fsl_qspi_devtype_data vybrid_data = { + .devtype = FSL_QUADSPI_VYBRID, + .rxfifo = SZ_128, + .txfifo = SZ_64, + .ahb_buf_size = SZ_1K, + .quirks = QUADSPI_QUIRK_SWAP_ENDIAN, +}; + +static const struct fsl_qspi_devtype_data imx6sx_data = { + .devtype = FSL_QUADSPI_IMX6SX, + .rxfifo = SZ_128, + .txfifo = SZ_512, + .ahb_buf_size = SZ_1K, + .quirks = QUADSPI_QUIRK_4X_INT_CLK | QUADSPI_QUIRK_TKT245618, }; + +static const struct fsl_qspi_devtype_data imx7d_data = { + .devtype = FSL_QUADSPI_IMX7D, + .rxfifo = SZ_512, + .txfifo = SZ_512, + .ahb_buf_size = SZ_1K, + .quirks = QUADSPI_QUIRK_TKT253890 | QUADSPI_QUIRK_4X_INT_CLK, }; + +static const struct fsl_qspi_devtype_data imx6ul_data = { + .devtype = FSL_QUADSPI_IMX6UL, + .rxfifo = SZ_128, + .txfifo = SZ_512, + .ahb_buf_size = SZ_1K, + .quirks = QUADSPI_QUIRK_TKT253890 | QUADSPI_QUIRK_4X_INT_CLK, }; + +static const struct fsl_qspi_devtype_data ls1021a_data = { + .devtype = FSL_QUADSPI_LS1021A, + .rxfifo = SZ_128, + .txfifo = SZ_64, + .ahb_buf_size = SZ_1K, + .quirks = 0, +}; + +static const struct fsl_qspi_devtype_data ls2080a_data = { + .devtype = FSL_QUADSPI_LS2080A, + .rxfifo = SZ_128, + .txfifo = SZ_64, + .ahb_buf_size = SZ_1K, + .quirks = QUADSPI_QUIRK_TKT253890, +}; + +struct fsl_qspi { + void __iomem *iobase; + void __iomem *ahb_addr; + u32 memmap_phy; + struct clk *clk, *clk_en; + struct device *dev; + struct completion c; + const struct fsl_qspi_devtype_data *devtype_data; + bool big_endian; + struct mutex lock; + struct pm_qos_request pm_qos_req; + int selected; +}; + +static inline int needs_swap_endian(struct fsl_qspi *q) { + return q->devtype_data->quirks & QUADSPI_QUIRK_SWAP_ENDIAN; } + +static inline int needs_4x_clock(struct fsl_qspi *q) { + return q->devtype_data->quirks & QUADSPI_QUIRK_4X_INT_CLK; } + +static inline int needs_fill_txfifo(struct fsl_qspi *q) { + return q->devtype_data->quirks & QUADSPI_QUIRK_TKT253890; } + +static inline int needs_wakeup_wait_mode(struct fsl_qspi *q) { + return q->devtype_data->quirks & QUADSPI_QUIRK_TKT245618; } + +/* + * An IC bug makes it necessary to rearrange the 32-bit data. + * Later chips, such as IMX6SLX, have fixed this bug. + */ +static inline u32 fsl_qspi_endian_xchg(struct fsl_qspi *q, u32 a) { + return needs_swap_endian(q) ? __swab32(a) : a; } + +/* + * R/W functions for big- or little-endian registers: + * The QSPI controller's endianness is independent of + * the CPU core's endianness. So far, although the CPU + * core is little-endian the QSPI controller can use + * big-endian or little-endian. + */ +static void qspi_writel(struct fsl_qspi *q, u32 val, void __iomem +*addr) { + if (q->big_endian) + iowrite32be(val, addr); + else + iowrite32(val, addr); +} + +static u32 qspi_readl(struct fsl_qspi *q, void __iomem *addr) { + if (q->big_endian) + return ioread32be(addr); + else + return ioread32(addr); +} + +static irqreturn_t fsl_qspi_irq_handler(int irq, void *dev_id) { + struct fsl_qspi *q = dev_id; + u32 reg; + + /* clear interrupt */ + reg = qspi_readl(q, q->iobase + QUADSPI_FR); + qspi_writel(q, reg, q->iobase + QUADSPI_FR); + + if (reg & QUADSPI_FR_TFF_MASK) + complete(&q->c); + + dev_dbg(q->dev, "QUADSPI_FR : 0x%.8x:0x%.8x\n", 0, reg); + return IRQ_HANDLED; +} + +static int fsl_qspi_check_buswidth(struct fsl_qspi *q, u8 width) { + switch (width) { + case 1: + case 2: + case 4: + return 0; + } + + return -ENOTSUPP; +} + +static bool fsl_qspi_supports_op(struct spi_mem *mem, + const struct spi_mem_op *op) +{ + struct fsl_qspi *q = spi_controller_get_devdata(mem->spi->master); + int ret; + + ret = fsl_qspi_check_buswidth(q, op->cmd.buswidth); + + if (op->addr.nbytes) + ret |= fsl_qspi_check_buswidth(q, op->addr.buswidth); + + if (op->dummy.nbytes) + ret |= fsl_qspi_check_buswidth(q, op->dummy.buswidth); + + if (op->data.nbytes) + ret |= fsl_qspi_check_buswidth(q, op->data.buswidth); + + if (ret) + return false; + + /* + * The number of instructions needed for the op, needs + * to fit into a single LUT entry. + */ + if (op->addr.nbytes + + (op->dummy.nbytes ? 1:0) + + (op->data.nbytes ? 1:0) > 6) + return false; + + /* Max 64 dummy clock cycles supported */ + if (op->dummy.nbytes * 8 / op->dummy.buswidth > 64) + return false; + + /* Max data length, check controller limits and alignment */ + if (op->data.dir == SPI_MEM_DATA_IN && + (op->data.nbytes > q->devtype_data->ahb_buf_size || + (op->data.nbytes > q->devtype_data->rxfifo - 4 && + !IS_ALIGNED(op->data.nbytes, 8)))) + return false; + + if (op->data.dir == SPI_MEM_DATA_OUT && + op->data.nbytes > q->devtype_data->txfifo) + return false; + + return true; +} + +static void fsl_qspi_prepare_lut(struct fsl_qspi *q, + const struct spi_mem_op *op) +{ + void __iomem *base = q->iobase; + u32 lutval[4] = {}; + int lutidx = 1, i; + + lutval[0] |= LUT_DEF(0, LUT_CMD, LUT_PAD(op->cmd.buswidth), + op->cmd.opcode); + + /* + * For some unknown reason, using LUT_ADDR doesn't work in some + * cases (at least with only one byte long addresses), so + * let's use LUT_MODE to write the address bytes one by one + */ + for (i = 0; i < op->addr.nbytes; i++) { + u8 addrbyte = op->addr.val >> (8 * (op->addr.nbytes - i - 1)); + + lutval[lutidx / 2] |= LUT_DEF(lutidx, LUT_MODE, + LUT_PAD(op->addr.buswidth), + addrbyte); + lutidx++; + } + + if (op->dummy.nbytes) { + lutval[lutidx / 2] |= LUT_DEF(lutidx, LUT_DUMMY, + LUT_PAD(op->dummy.buswidth), + op->dummy.nbytes * 8 / + op->dummy.buswidth); + lutidx++; + } + + if (op->data.nbytes) { + lutval[lutidx / 2] |= LUT_DEF(lutidx, + op->data.dir == SPI_MEM_DATA_IN ? + LUT_FSL_READ : LUT_FSL_WRITE, + LUT_PAD(op->data.buswidth), + 0); + lutidx++; + } + + lutval[lutidx / 2] |= LUT_DEF(lutidx, LUT_STOP, 0, 0); + + /* unlock LUT */ + qspi_writel(q, QUADSPI_LUTKEY_VALUE, q->iobase + QUADSPI_LUTKEY); + qspi_writel(q, QUADSPI_LCKER_UNLOCK, q->iobase + QUADSPI_LCKCR); + + /* fill LUT */ + for (i = 0; i < ARRAY_SIZE(lutval); i++) + qspi_writel(q, lutval[i], base + QUADSPI_LUT_REG(i)); + + /* lock LUT */ + qspi_writel(q, QUADSPI_LUTKEY_VALUE, q->iobase + QUADSPI_LUTKEY); + qspi_writel(q, QUADSPI_LCKER_LOCK, q->iobase + QUADSPI_LCKCR); } + +static int fsl_qspi_clk_prep_enable(struct fsl_qspi *q) { + int ret; + + ret = clk_prepare_enable(q->clk_en); + if (ret) + return ret; + + ret = clk_prepare_enable(q->clk); + if (ret) { + clk_disable_unprepare(q->clk_en); + return ret; + } + + if (needs_wakeup_wait_mode(q)) + pm_qos_add_request(&q->pm_qos_req, PM_QOS_CPU_DMA_LATENCY, 0); + + return 0; +} + +static void fsl_qspi_clk_disable_unprep(struct fsl_qspi *q) { + if (needs_wakeup_wait_mode(q)) + pm_qos_remove_request(&q->pm_qos_req); + + clk_disable_unprepare(q->clk); + clk_disable_unprepare(q->clk_en); +} + +static void fsl_qspi_select_mem(struct fsl_qspi *q, struct spi_device +*spi) { + unsigned long rate = spi->max_speed_hz; + int ret, i; + u32 map_addr; + + if (q->selected == spi->chip_select) + return; + + /* + * In HW there can be a maximum of four chips on two buses with + * two chip selects on each bus. We use four chip selects in SW + * to differentiate between the four chips. + * We use the SFA1AD, SFA2AD, SFB1AD, SFB2AD registers to select + * the chip we want to access. + */ + for (i = 0; i < 4; i++) { + if (i < spi->chip_select) + map_addr = q->memmap_phy; + else + map_addr = q->memmap_phy + + 2 * q->devtype_data->ahb_buf_size; + + qspi_writel(q, map_addr, q->iobase + QUADSPI_SFA1AD + (i * 4)); + } + + if (needs_4x_clock(q)) + rate *= 4; + + fsl_qspi_clk_disable_unprep(q); + + ret = clk_set_rate(q->clk, rate); + if (ret) + return; + + ret = fsl_qspi_clk_prep_enable(q); + if (ret) + return; + + q->selected = spi->chip_select; +} + +static void fsl_qspi_read_ahb(struct fsl_qspi *q, const struct +spi_mem_op *op) { + static int seq; + + /* + * We want to avoid needing to invalidate the cache by issueing + * a reset to the AHB and Serial Flash domain, as this needs + * time. So we change the address on each read to trigger an + * actual read operation on the flash. The actual address for + * the flash memory is set by programming the LUT. + */ + memcpy_fromio(op->data.buf.in, + q->ahb_addr + + (seq * q->devtype_data->ahb_buf_size), + op->data.nbytes); + + seq = seq ? 0 : 1; +} + +static void fsl_qspi_fill_txfifo(struct fsl_qspi *q, + const struct spi_mem_op *op) +{ + void __iomem *base = q->iobase; + int i; + + for (i = 0; i < op->data.nbytes; i += 4) { + u32 val = 0; + + memcpy(&val, op->data.buf.out + i, + min_t(unsigned int, op->data.nbytes - i, 4)); + + val = fsl_qspi_endian_xchg(q, val); + qspi_writel(q, val, base + QUADSPI_TBDR); + } + + if (needs_fill_txfifo(q)) { + for (; i < 16; i += 4) + qspi_writel(q, 0, base + QUADSPI_TBDR); + } +} + +static void fsl_qspi_read_rxfifo(struct fsl_qspi *q, + const struct spi_mem_op *op) +{ + void __iomem *base = q->iobase; + int i; + u8 *buf = op->data.buf.in; + + for (i = 0; i < op->data.nbytes; i += 4) { + u32 val = qspi_readl(q, base + QUADSPI_RBDR(i / 4)); + + val = fsl_qspi_endian_xchg(q, val); + + memcpy(buf + i, &val, + min_t(unsigned int, op->data.nbytes - i, 4)); + } +} + +static int fsl_qspi_do_op(struct fsl_qspi *q, const struct spi_mem_op +*op) { + void __iomem *base = q->iobase; + int err = 0; + + init_completion(&q->c); + + /* + * Always start the sequence at the same index since we update + * the LUT at each exec_op() call. And also specify the DATA + * length, since it's has not been specified in the LUT. + */ + qspi_writel(q, op->data.nbytes | + (SEQID_LUT << QUADSPI_IPCR_SEQID_SHIFT), + base + QUADSPI_IPCR); + + /* Wait for the interrupt. */ + if (!wait_for_completion_timeout(&q->c, msecs_to_jiffies(1000))) + err = -ETIMEDOUT; + + if (!err && op->data.nbytes && op->data.dir == SPI_MEM_DATA_IN) + fsl_qspi_read_rxfifo(q, op); + + return err; +} + +static int fsl_qspi_exec_op(struct spi_mem *mem, const struct +spi_mem_op *op) { + struct fsl_qspi *q = spi_controller_get_devdata(mem->spi->master); + void __iomem *base = q->iobase; + int err = 0; + + mutex_lock(&q->lock); + + /* wait for the controller being ready */ + do { + u32 status; + + status = qspi_readl(q, base + QUADSPI_SR); + if (status & + (QUADSPI_SR_IP_ACC_MASK | QUADSPI_SR_AHB_ACC_MASK)) { + udelay(1); + dev_dbg(q->dev, "The controller is busy, 0x%x\n", + status); + continue; + } + break; + } while (1); + + fsl_qspi_select_mem(q, mem->spi); + + qspi_writel(q, q->memmap_phy, base + QUADSPI_SFAR); + + qspi_writel(q, + qspi_readl(q, base + QUADSPI_MCR) | + QUADSPI_MCR_CLR_RXF_MASK | QUADSPI_MCR_CLR_TXF_MASK, + base + QUADSPI_MCR); + + qspi_writel(q, QUADSPI_SPTRCLR_BFPTRC | QUADSPI_SPTRCLR_IPPTRC, + base + QUADSPI_SPTRCLR); + + fsl_qspi_prepare_lut(q, op); + + /* + * If we have large chunks of data, we read them through the AHB bus + * by accessing the mapped memory. In all other cases we use + * IP commands to access the flash. + */ + if (op->data.nbytes > (q->devtype_data->rxfifo - 4) && + op->data.dir == SPI_MEM_DATA_IN) { + fsl_qspi_read_ahb(q, op); + } else { + qspi_writel(q, + QUADSPI_RBCT_WMRK_MASK | QUADSPI_RBCT_RXBRD_USEIPS, + base + QUADSPI_RBCT); + + if (op->data.nbytes && op->data.dir == SPI_MEM_DATA_OUT) + fsl_qspi_fill_txfifo(q, op); + + err = fsl_qspi_do_op(q, op); + } + + mutex_unlock(&q->lock); + + return err; +} + +static int fsl_qspi_adjust_op_size(struct spi_mem *mem, struct +spi_mem_op *op) { + struct fsl_qspi *q = spi_controller_get_devdata(mem->spi->master); + + if (op->data.dir == SPI_MEM_DATA_OUT) { + if (op->data.nbytes > q->devtype_data->txfifo) + op->data.nbytes = q->devtype_data->txfifo; + } else { + if (op->data.nbytes > q->devtype_data->ahb_buf_size) + op->data.nbytes = q->devtype_data->ahb_buf_size; + else if (op->data.nbytes > (q->devtype_data->rxfifo - 4)) + op->data.nbytes = ALIGN_DOWN(op->data.nbytes, 8); + } + + return 0; +} + +static int fsl_qspi_default_setup(struct fsl_qspi *q) { + void __iomem *base = q->iobase; + u32 reg; + int ret; + + /* disable and unprepare clock to avoid glitch pass to controller */ + fsl_qspi_clk_disable_unprep(q); + + /* the default frequency, we will change it later if necessary. */ + ret = clk_set_rate(q->clk, 66000000); + if (ret) + return ret; + + ret = fsl_qspi_clk_prep_enable(q); + if (ret) + return ret; + + /* Reset the module */ + qspi_writel(q, QUADSPI_MCR_SWRSTSD_MASK | QUADSPI_MCR_SWRSTHD_MASK, + base + QUADSPI_MCR); + udelay(1); + + /* Disable the module */ + qspi_writel(q, QUADSPI_MCR_MDIS_MASK | QUADSPI_MCR_RESERVED_MASK, + base + QUADSPI_MCR); + + reg = qspi_readl(q, base + QUADSPI_SMPR); + qspi_writel(q, reg & ~(QUADSPI_SMPR_FSDLY_MASK + | QUADSPI_SMPR_FSPHS_MASK + | QUADSPI_SMPR_HSENA_MASK + | QUADSPI_SMPR_DDRSMP_MASK), base + QUADSPI_SMPR); + + /* We only use the buffer3 for AHB read */ + qspi_writel(q, 0, base + QUADSPI_BUF0IND); + qspi_writel(q, 0, base + QUADSPI_BUF1IND); + qspi_writel(q, 0, base + QUADSPI_BUF2IND); + + qspi_writel(q, SEQID_LUT << QUADSPI_BFGENCR_SEQID_SHIFT, + q->iobase + QUADSPI_BFGENCR); + qspi_writel(q, QUADSPI_RBCT_WMRK_MASK, base + QUADSPI_RBCT); + qspi_writel(q, QUADSPI_BUF3CR_ALLMST_MASK | + ((q->devtype_data->ahb_buf_size / 8) << + QUADSPI_BUF3CR_ADATSZ_SHIFT), + base + QUADSPI_BUF3CR); + + q->selected = -1; + + /* Enable the module */ + qspi_writel(q, QUADSPI_MCR_RESERVED_MASK | QUADSPI_MCR_END_CFG_MASK, + base + QUADSPI_MCR); + + /* clear all interrupt status */ + qspi_writel(q, 0xffffffff, q->iobase + QUADSPI_FR); + + /* enable the interrupt */ + qspi_writel(q, QUADSPI_RSER_TFIE, q->iobase + QUADSPI_RSER); + + return 0; +} + +static const char *fsl_qspi_get_name(struct spi_mem *mem) { + struct fsl_qspi *q = spi_controller_get_devdata(mem->spi->master); + struct device *dev = &mem->spi->dev; + const char *name; + + /* + * In order to keep mtdparts compatible with the old MTD driver at + * mtd/spi-nor/fsl-quadspi.c, we set a custom name derived from the + * platform_device of the controller. + */ + if (of_get_available_child_count(q->dev->of_node) == 1) + name = dev_name(q->dev); + else + name = devm_kasprintf(dev, GFP_KERNEL, + "%s-%d", dev_name(q->dev), + mem->spi->chip_select); + + if (!name) { + dev_err(dev, "failed to get memory for custom flash name\n"); + return dev_name(q->dev); + } + + return name; +} + +static const struct spi_controller_mem_ops fsl_qspi_mem_ops = { + .adjust_op_size = fsl_qspi_adjust_op_size, + .supports_op = fsl_qspi_supports_op, + .exec_op = fsl_qspi_exec_op, + .get_name = fsl_qspi_get_name, +}; + +static int fsl_qspi_probe(struct platform_device *pdev) { + struct spi_controller *ctlr; + struct device *dev = &pdev->dev; + struct device_node *np = dev->of_node; + struct resource *res; + struct fsl_qspi *q; + int ret; + + ctlr = spi_alloc_master(&pdev->dev, sizeof(*q)); + if (!ctlr) + return -ENOMEM; + + ctlr->mode_bits = SPI_RX_DUAL | SPI_RX_QUAD | + SPI_TX_DUAL | SPI_TX_QUAD; + + q = spi_controller_get_devdata(ctlr); + q->dev = dev; + q->devtype_data = of_device_get_match_data(dev); + if (!q->devtype_data) { + ret = -ENODEV; + goto err_put_ctrl; + } + + platform_set_drvdata(pdev, q); + + /* find the resources */ + res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "QuadSPI"); + q->iobase = devm_ioremap_resource(dev, res); + if (IS_ERR(q->iobase)) { + ret = PTR_ERR(q->iobase); + goto err_put_ctrl; + } + + q->big_endian = of_property_read_bool(np, "big-endian"); + + res = platform_get_resource_byname(pdev, IORESOURCE_MEM, + "QuadSPI-memory"); + q->ahb_addr = devm_ioremap_resource(dev, res); + if (IS_ERR(q->ahb_addr)) { + ret = PTR_ERR(q->ahb_addr); + goto err_put_ctrl; + } + + q->memmap_phy = res->start; + + /* find the clocks */ + q->clk_en = devm_clk_get(dev, "qspi_en"); + if (IS_ERR(q->clk_en)) { + ret = PTR_ERR(q->clk_en); + goto err_put_ctrl; + } + + q->clk = devm_clk_get(dev, "qspi"); + if (IS_ERR(q->clk)) { + ret = PTR_ERR(q->clk); + goto err_put_ctrl; + } + + ret = fsl_qspi_clk_prep_enable(q); + if (ret) { + dev_err(dev, "can not enable the clock\n"); + goto err_put_ctrl; + } + + /* find the irq */ + ret = platform_get_irq(pdev, 0); + if (ret < 0) { + dev_err(dev, "failed to get the irq: %d\n", ret); + goto err_disable_clk; + } + + ret = devm_request_irq(dev, ret, + fsl_qspi_irq_handler, 0, pdev->name, q); + if (ret) { + dev_err(dev, "failed to request irq: %d\n", ret); + goto err_disable_clk; + } + + mutex_init(&q->lock); + + ctlr->bus_num = -1; + ctlr->num_chipselect = 4; + ctlr->mem_ops = &fsl_qspi_mem_ops; + + fsl_qspi_default_setup(q); + + ctlr->dev.of_node = np; + + ret = spi_register_controller(ctlr); + if (ret) + goto err_destroy_mutex; + + return 0; + +err_destroy_mutex: + mutex_destroy(&q->lock); + +err_disable_clk: + fsl_qspi_clk_disable_unprep(q); + +err_put_ctrl: + spi_controller_put(ctlr); + + dev_err(dev, "Freescale QuadSPI probe failed\n"); + return ret; +} + +static int fsl_qspi_remove(struct platform_device *pdev) { + struct fsl_qspi *q = platform_get_drvdata(pdev); + + /* disable the hardware */ + qspi_writel(q, QUADSPI_MCR_MDIS_MASK, q->iobase + QUADSPI_MCR); + qspi_writel(q, 0x0, q->iobase + QUADSPI_RSER); + + fsl_qspi_clk_disable_unprep(q); + + mutex_destroy(&q->lock); + + if (q->ahb_addr) + iounmap(q->ahb_addr); + + return 0; +} + +static int fsl_qspi_suspend(struct platform_device *pdev, pm_message_t +state) { + return 0; +} + +static int fsl_qspi_resume(struct platform_device *pdev) { + struct fsl_qspi *q = platform_get_drvdata(pdev); + + fsl_qspi_default_setup(q); + + return 0; +} + +static const struct of_device_id fsl_qspi_dt_ids[] = { + { .compatible = "fsl,vf610-qspi", .data = &vybrid_data, }, + { .compatible = "fsl,imx6sx-qspi", .data = &imx6sx_data, }, + { .compatible = "fsl,imx7d-qspi", .data = &imx7d_data, }, + { .compatible = "fsl,imx6ul-qspi", .data = &imx6ul_data, }, + { .compatible = "fsl,ls1021a-qspi", .data = &ls1021a_data, }, + { .compatible = "fsl,ls2080a-qspi", .data = &ls2080a_data, }, + { /* sentinel */ } +}; +MODULE_DEVICE_TABLE(of, fsl_qspi_dt_ids); + +static struct platform_driver fsl_qspi_driver = { + .driver = { + .name = "fsl-quadspi", + .of_match_table = fsl_qspi_dt_ids, + }, + .probe = fsl_qspi_probe, + .remove = fsl_qspi_remove, + .suspend = fsl_qspi_suspend, + .resume = fsl_qspi_resume, +}; +module_platform_driver(fsl_qspi_driver); + +MODULE_DESCRIPTION("Freescale QuadSPI Controller Driver"); +MODULE_AUTHOR("Freescale Semiconductor Inc."); MODULE_AUTHOR("Boris +Brezillion <boris.brezil...@bootlin.com>"); MODULE_AUTHOR("Frieder +Schrempf <frieder.schre...@exceet.de>"); MODULE_LICENSE("GPL v2"); -- 2.7.4
