Hi Bjorn,

On 5/23/2018 10:50 AM, Bjorn Andersson wrote:
> Migrate the MSS remoteproc driver to use the newly extracted helper
> functions.
> 
> Signed-off-by: Bjorn Andersson <bjorn.anders...@linaro.org>
> ---
>  drivers/remoteproc/Kconfig         |   4 +
>  drivers/remoteproc/qcom_q6v5_pil.c | 157 +++--------------------------
>  2 files changed, 19 insertions(+), 142 deletions(-)
> 
> diff --git a/drivers/remoteproc/Kconfig b/drivers/remoteproc/Kconfig
> index d51d155cf8bd..2316908e9788 100644
> --- a/drivers/remoteproc/Kconfig
> +++ b/drivers/remoteproc/Kconfig
> @@ -116,6 +116,10 @@ config QCOM_Q6V5_PIL
>       depends on RPMSG_QCOM_GLINK_SMEM || RPMSG_QCOM_GLINK_SMEM=n
>       depends on QCOM_SYSMON || QCOM_SYSMON=n
>       select MFD_SYSCON
> +     select QCOM_Q6V5_COMMON

 The below three are duplicate.

> +     select QCOM_RPROC_COMMON
> +     select QCOM_SCM
> +     select QCOM_Q6V5_COMMON
>       select QCOM_RPROC_COMMON
>       select QCOM_SCM

<..>

> @@ -946,16 +934,10 @@ static int q6v5_stop(struct rproc *rproc)
>  
>       qproc->running = false;
>  
> -     qcom_smem_state_update_bits(qproc->state,
> -                                 BIT(qproc->stop_bit), BIT(qproc->stop_bit));
> -
> -     ret = wait_for_completion_timeout(&qproc->stop_done,
> -                                       msecs_to_jiffies(5000));
> -     if (ret == 0)
> +     ret = qcom_q6v5_request_stop(&qproc->q6v5);
> +     if (ret == -ETIMEDOUT)
>               dev_err(qproc->dev, "timed out on wait\n");
>  
> -     qcom_smem_state_update_bits(qproc->state, BIT(qproc->stop_bit), 0);
> -
>       q6v5proc_halt_axi_port(qproc, qproc->halt_map, qproc->halt_q6);
>       q6v5proc_halt_axi_port(qproc, qproc->halt_map, qproc->halt_modem);
>       q6v5proc_halt_axi_port(qproc, qproc->halt_map, qproc->halt_nc);
> @@ -976,9 +958,8 @@ static int q6v5_stop(struct rproc *rproc)
>  
>       q6v5_reset_assert(qproc);
>  
> -     disable_irq(qproc->handover_irq);
> -
> -     if (!qproc->proxy_unvoted) {
> +     ret = qcom_q6v5_unprepare(&qproc->q6v5);
> +     if (ret) {
>               q6v5_clk_disable(qproc->dev, qproc->proxy_clks,
>                                qproc->proxy_clk_count);
>               q6v5_regulator_disable(qproc, qproc->proxy_regs,

 Nit, can qcom_msa_handover api be used instead here ?

 Rest all looks good,
    reviewed-by: Sricharan R <sricha...@codeaurora.org>

Regards,
 Sricharan

-- 
"QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of 
Code Aurora Forum, hosted by The Linux Foundation

---
This email has been checked for viruses by Avast antivirus software.
https://www.avast.com/antivirus

Reply via email to