Hello Sudeep,
Thanks for your comments.
On 6/14/2018 4:17 PM, Sudeep Holla wrote:
On 13/06/18 19:13, Taniya Das wrote:
Hello Sudeep,
Thanks for review comments.
On 6/13/2018 4:56 PM, Sudeep Holla wrote:
[...]
You are bit inconsistent on the wordings. Some places you refer this as
hardware engine. If so, please drop all references to firmware/FW. If
it's firmware then update accordingly.
It is a hardware engine which has a firmware to take care of the
managing the frequency request from OS. That is reason to refer it as a
firmware.
Yes I did guess that initially, but I failed to understand when
different bindings were posted to deal with devfreq and cpufreq with the
same firmware. Ideally if it's the firmware you are talking to, place
all these under /firmware node and align all those with single binding.
The OS is not aware of the firmware and OS only knows about the hardware
engine and has to put forward it's request to the hardware engine using
the "Perf" state register in both devfreq & cpufreq. So would it be
still required to put under the /firmware node?
Is there anything else that this firmware deals with ? If so all those
need to be put in one place.
We deal only with the CPU frequency and L3 frequency(devfreq).
+Properties:
+- compatible
+ Usage: required
+ Value type: <string>
+ Definition: must be "qcom,cpufreq-fw".
+
+* Property qcom,freq-domain
+Devices supporting freq-domain must set their "qcom,freq-domain"
property with
+phandle to a freq_domain_table in their DT node.
+
+* Frequency Domain Table Node
+
+This describes the frequency domain belonging to a device.
+This node can have following properties:
+
+- reg
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: Addresses and sizes for the memory of the perf
+ , lut and enable bases.
+ perf - indicates the base address for the desired
+ performance state to be set.
+ lut - indicates the look up table base address for the
+ cpufreq driver to read frequencies.
+ enable - indicates the enable register for firmware.
You still didn't answer my earlier question.
OS might touch one or 2 registers in lots of IP blocks. I am not sure
why those are any different from these. Are you trying to align with any
other bindings or specification. Are you trying to make this binding
generic here ? I understand if it was trying to generalize the firmware
interface, but you also state it's a hardware engine. So I fail to see
the need for such specificity here. Why not define the whole IP block
and the driver knows where to access these specific ones as they are
specific to this hardware block. In that way if you decide to add more
data, it's extensible easily without the need for patching DT.
Sorry Sudeep I missed replying to your earlier query.
The High level OS(HLOS) would require to access only these specific
registers from this IP block and just mapping the whole block(huge
region) is unnecessary from the OS point of View. As of now it is a
generic binding for all using this IP block to manage frequency
requests. The OS would only have to know the frequencies supported i.e
to read the lookup table registers and put across the OS request using
the performance state register.
I am not sure if you need to defining bindings to save OSPM IO mapping.
In-fact you may be adding more mapping unnecessarily. The mappings are
page aligned and spiting the registers and mapping them individually may
result in more mappings.
I just need to know the rational for such specific choice of registers.
I assume it's aligned to some other standard specifications like CPPC
though not identical.
I am not sure of the query but there is no other register that the OS is
required to use other than the ones defined here.
Eg. Suppose you need some information on power curve for EAS energy
model, I really hate to update DT for that or even do a mix with DT just
because f/w is no longer modifiable.
For now we are safe.
What do you mean by that ?
I meant here was currently there is no such known case where the f/w is
no longer modifiable and we need to extend device tree bindings.
It should be easily extensible is what I am
trying to say. You can add more info and alter the information in the
driver with compatibles if you keep the register info as minimum as
possible. For now, you have enable, set and lut registers. What if you
want to provide power numbers ?
Yes I do understand the intent of mapping the whole register space, but
as per the HW specs these 3 registers would be the only ones required
for now. I do not think this hardware engine has any information on the
power numbers.
--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation.
--
