This is a nice improvement, a few remaining questions inline.
On Mon, Jun 25, 2018 at 07:10:10PM +0530, Balakrishna Godavarthi wrote:
> In function qca_setup, we set initial and operating speeds for Qualcomm
> Bluetooth SoC's. This block of code is common across different
> Qualcomm Bluetooth SoC's. Instead of duplicating the code, created
> a wrapper function to set the speeds. So that future coming SoC's
> can use these wrapper functions to set speeds.
>
> Signed-off-by: Balakrishna Godavarthi <[email protected]>
> ---
> Changes in v8:
> * common function to set INIT and operating speeds.
> * moved hardware flow control to qca_set_speed().
>
> Changes in v7:
> * initial patch
> * created wrapper functions for init and operating speeds.
> ---
> drivers/bluetooth/hci_qca.c | 89 +++++++++++++++++++++++++++----------
> 1 file changed, 65 insertions(+), 24 deletions(-)
>
> diff --git a/drivers/bluetooth/hci_qca.c b/drivers/bluetooth/hci_qca.c
> index fe62420ef838..38b7dbe6c897 100644
> --- a/drivers/bluetooth/hci_qca.c
> +++ b/drivers/bluetooth/hci_qca.c
> @@ -119,6 +119,11 @@ struct qca_data {
> u64 votes_off;
> };
>
> +enum qca_speed_type {
> + QCA_INIT_SPEED = 1,
> + QCA_OPER_SPEED
> +};
> +
> struct qca_serdev {
> struct hci_uart serdev_hu;
> struct gpio_desc *bt_en;
> @@ -923,6 +928,60 @@ static inline void host_set_baudrate(struct hci_uart
> *hu, unsigned int speed)
> hci_uart_set_baudrate(hu, speed);
> }
>
> +static unsigned int qca_get_speed(struct hci_uart *hu,
> + enum qca_speed_type speed_type)
> +{
> + unsigned int speed = 0;
> +
> + if (speed_type == QCA_INIT_SPEED) {
> + if (hu->init_speed)
> + speed = hu->init_speed;
> + else if (hu->proto->init_speed)
> + speed = hu->proto->init_speed;
> + } else {
> + if (hu->oper_speed)
> + speed = hu->oper_speed;
> + else if (hu->proto->oper_speed)
> + speed = hu->proto->oper_speed;
> + }
> +
> + return speed;
> +}
> +
> +static int qca_set_speed(struct hci_uart *hu, enum qca_speed_type speed_type)
> +{
> + unsigned int speed, qca_baudrate;
> + int ret;
> +
> + if (speed_type == QCA_INIT_SPEED) {
> + speed = qca_get_speed(hu, QCA_INIT_SPEED);
> + if (speed)
> + host_set_baudrate(hu, speed);
> + else
> + bt_dev_err(hu->hdev, "Init speed should be non zero");
The check for 'speed == 0' is done in multiple places. From this
code I deduce that it is expected that both INIT and OPER speed are
set to non-zero values. What happens if either of them is zero? Is the
driver still operational?
> + return 0;
> + }
> +
> + speed = qca_get_speed(hu, QCA_OPER_SPEED);
> + if (!speed) {
> + bt_dev_err(hu->hdev, "operating speed should be non zero");
> + return 0;
> + }
> +
> + qca_baudrate = qca_get_baudrate_value(speed);
> + bt_dev_info(hu->hdev, "Set UART speed to %d", speed);
> + ret = qca_set_baudrate(hu->hdev, qca_baudrate);
> + if (ret) {
> + bt_dev_err(hu->hdev, "Failed to change the baudrate (%d)", ret);
> + return ret;
> + }
> +
> + host_set_baudrate(hu, speed);
> +
> + return ret;
> +}
In the discussion on "[v7,8/8] Bluetooth: hci_qca: Add support for
Qualcomm Bluetooth chip wcn3990" you mentioned the possbility to move
the hci_uart_set_flow_control() calls into _set_speed(). This seemed
interesting but finally it isn't done in this series. Did you
encounter that it is not feasible/desirable for some reason?
> +
> static int qca_setup(struct hci_uart *hu)
> {
> struct hci_dev *hdev = hu->hdev;
> @@ -937,35 +996,17 @@ static int qca_setup(struct hci_uart *hu)
> clear_bit(STATE_IN_BAND_SLEEP_ENABLED, &qca->flags);
>
> /* Setup initial baudrate */
> - speed = 0;
> - if (hu->init_speed)
> - speed = hu->init_speed;
> - else if (hu->proto->init_speed)
> - speed = hu->proto->init_speed;
> -
> - if (speed)
> - host_set_baudrate(hu, speed);
> + qca_set_speed(hu, QCA_INIT_SPEED);
>
> /* Setup user speed if needed */
> - speed = 0;
> - if (hu->oper_speed)
> - speed = hu->oper_speed;
> - else if (hu->proto->oper_speed)
> - speed = hu->proto->oper_speed;
> + ret = qca_set_speed(hu, QCA_OPER_SPEED);
> + if (ret)
> + return ret;
>
> - if (speed) {
> + speed = qca_get_speed(hu, QCA_OPER_SPEED);
> + if (speed)
> qca_baudrate = qca_get_baudrate_value(speed);
Is the check here necessary? qca_get_baudrate_value() returns
QCA_BAUDRATE_115200 for a zero speed.
