Add support for the Zodiac Inflight Innovations CFU1
board (VF610-based).
Cc: Shawn Guo <shawn...@kernel.org>
Cc: Fabio Estevam <fabio.este...@nxp.com>
Cc: cphe...@gmail.com
Cc: linux-arm-ker...@lists.infradead.org
Cc: devicet...@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Fabio Estevam <fabio.este...@nxp.com>
Signed-off-by: Andrew Lunn <and...@lunn.ch>
Signed-off-by: Andrey Smirnov <andrew.smir...@gmail.com>
---
Changes since [v1]:
- Fixed DT warning when compiling with W=1
- Collected Reviewed-by from Fabio
[v1] lkml.kernel.org/r/20180719005941.10458-1-andrew.smir...@gmail.com
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/vf610-zii-cfu1.dts | 305 +++++++++++++++++++++++++++
2 files changed, 306 insertions(+)
create mode 100644 arch/arm/boot/dts/vf610-zii-cfu1.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index e331b2c16539..85797819fdd9 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -569,6 +569,7 @@ dtb-$(CONFIG_SOC_VF610) += \
vf610-cosmic.dtb \
vf610m4-cosmic.dtb \
vf610-twr.dtb \
+ vf610-zii-cfu1.dtb \
vf610-zii-dev-rev-b.dtb \
vf610-zii-dev-rev-c.dtb \
vf610-zii-ssmb-spu3.dtb
diff --git a/arch/arm/boot/dts/vf610-zii-cfu1.dts
b/arch/arm/boot/dts/vf610-zii-cfu1.dts
new file mode 100644
index 000000000000..37777cf22e67
--- /dev/null
+++ b/arch/arm/boot/dts/vf610-zii-cfu1.dts
@@ -0,0 +1,305 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+
+/*
+ * Copyright (C) 2018 Zodiac Inflight Innovations
+ */
+
+/dts-v1/;
+#include "vf610.dtsi"
+
+/ {
+ model = "ZII VF610 CFU1 Board";
+ compatible = "zii,vf610cfu1", "zii,vf610dev", "fsl,vf610";
+
+ chosen {
+ stdout-path = &uart0;
+ };
+
+ memory@80000000 {
+ reg = <0x80000000 0x20000000>;
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+ pinctrl-0 = <&pinctrl_leds_debug>;
+ pinctrl-names = "default";
+
+ led-debug {
+ label = "zii:green:debug1";
+ gpios = <&gpio2 18 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ max-brightness = <1>;
+ };
+
+ led-fail {
+ label = "zii:red:fail";
+ gpios = <&gpio3 12 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ max-brightness = <1>;
+ };
+
+ led-status {
+ label = "zii:green:status";
+ gpios = <&gpio3 13 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ max-brightness = <1>;
+ };
+
+ led-debug-a {
+ label = "zii:green:debug_a";
+ gpios = <&gpio3 14 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ max-brightness = <1>;
+ };
+
+ led-debug-b {
+ label = "zii:green:debug_b";
+ gpios = <&gpio3 15 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ max-brightness = <1>;
+ };
+ };
+
+ reg_vcc_3v3_mcu: regulator-vcc-3v3-mcu {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_3v3_mcu";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+};
+
+&adc0 {
+ vref-supply = <®_vcc_3v3_mcu>;
+ status = "okay";
+};
+
+&adc1 {
+ vref-supply = <®_vcc_3v3_mcu>;
+ status = "okay";
+};
+
+&dspi1 {
+ bus-num = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_dspi1>;
+ status = "okay";
+
+ m25p128@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "m25p128", "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <50000000>;
+
+ partition@0 {
+ label = "m25p128-0";
+ reg = <0x0 0x01000000>;
+ };
+ };
+};
+
+&edma0 {
+ status = "okay";
+};
+
+&edma1 {
+ status = "okay";
+};
+
+&esdhc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_esdhc0>;
+ bus-width = <8>;
+ non-removable;
+ no-1-8-v;
+ keep-power-in-suspend;
+ status = "okay";
+};
+
+&esdhc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_esdhc1>;
+ bus-width = <4>;
+ status = "okay";
+};
+
+&fec1 {
+ phy-mode = "rmii";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_fec1>;
+ status = "okay";
+
+ fixed-link {
+ speed = <100>;
+ full-duplex;
+ };
+
+ mdio1: mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+
+ switch0: switch0@0 {
+ compatible = "marvell,mv88e6085";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_switch>;
+ reg = <0>;
+ eeprom-length = <512>;
+ interrupt-parent = <&gpio3>;
+ interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ reset-gpios = <&gpio3 11 GPIO_ACTIVE_LOW>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ label = "eth_cu_1000_1";
+ };
+
+ port@1 {
+ reg = <1>;
+ label = "eth_cu_1000_2";
+ };
+
+ port@2 {
+ reg = <2>;
+ label = "eth_cu_1000_3";
+ };
+
+ port@6 {
+ reg = <6>;
+ label = "cpu";
+ ethernet = <&fec1>;
+
+ fixed-link {
+ speed = <100>;
+ full-duplex;
+ };
+ };
+ };
+ };
+ };
+};
+
+&i2c0 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c0>;
+ status = "okay";
+
+ pca9554@22 {
+ compatible = "nxp,pca9554";
+ reg = <0x22>;
+ gpio-controller;
+ };
+
+ lm75@48 {
+ compatible = "national,lm75";
+ reg = <0x48>;
+ };
+
+ at24c04@52 {
+ compatible = "atmel,24c04";
+ reg = <0x52>;
+ label = "nvm";
+ };
+
+ at24c04@54 {
+ compatible = "atmel,24c04";
+ reg = <0x54>;
+ label = "nameplate";
+ };
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart0>;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_dspi1: dspi1grp {
+ fsl,pins = <
+ VF610_PAD_PTD5__DSPI1_CS0 0x1182
+ VF610_PAD_PTC6__DSPI1_SIN 0x1181
+ VF610_PAD_PTC7__DSPI1_SOUT 0x1182
+ VF610_PAD_PTC8__DSPI1_SCK 0x1182
+ >;
+ };
+
+ pinctrl_esdhc0: esdhc0grp {
+ fsl,pins = <
+ VF610_PAD_PTC0__ESDHC0_CLK 0x31ef
+ VF610_PAD_PTC1__ESDHC0_CMD 0x31ef
+ VF610_PAD_PTC2__ESDHC0_DAT0 0x31ef
+ VF610_PAD_PTC3__ESDHC0_DAT1 0x31ef
+ VF610_PAD_PTC4__ESDHC0_DAT2 0x31ef
+ VF610_PAD_PTC5__ESDHC0_DAT3 0x31ef
+ VF610_PAD_PTD23__ESDHC0_DAT4 0x31ef
+ VF610_PAD_PTD22__ESDHC0_DAT5 0x31ef
+ VF610_PAD_PTD21__ESDHC0_DAT6 0x31ef
+ VF610_PAD_PTD20__ESDHC0_DAT7 0x31ef
+ >;
+ };
+
+ pinctrl_esdhc1: esdhc1grp {
+ fsl,pins = <
+ VF610_PAD_PTA24__ESDHC1_CLK 0x31ef
+ VF610_PAD_PTA25__ESDHC1_CMD 0x31ef
+ VF610_PAD_PTA26__ESDHC1_DAT0 0x31ef
+ VF610_PAD_PTA27__ESDHC1_DAT1 0x31ef
+ VF610_PAD_PTA28__ESDHC1_DATA2 0x31ef
+ VF610_PAD_PTA29__ESDHC1_DAT3 0x31ef
+ >;
+ };
+
+ pinctrl_fec1: fec1grp {
+ fsl,pins = <
+ VF610_PAD_PTA6__RMII_CLKIN 0x30d1
+ VF610_PAD_PTC9__ENET_RMII1_MDC 0x30fe
+ VF610_PAD_PTC10__ENET_RMII1_MDIO 0x30d3
+ VF610_PAD_PTC11__ENET_RMII1_CRS 0x30d1
+ VF610_PAD_PTC12__ENET_RMII1_RXD1 0x30d1
+ VF610_PAD_PTC13__ENET_RMII1_RXD0 0x30d1
+ VF610_PAD_PTC14__ENET_RMII1_RXER 0x30d1
+ VF610_PAD_PTC15__ENET_RMII1_TXD1 0x30d2
+ VF610_PAD_PTC16__ENET_RMII1_TXD0 0x30d2
+ VF610_PAD_PTC17__ENET_RMII1_TXEN 0x30d2
+ >;
+ };
+
+ pinctrl_i2c0: i2c0grp {
+ fsl,pins = <
+ VF610_PAD_PTB14__I2C0_SCL 0x37ff
+ VF610_PAD_PTB15__I2C0_SDA 0x37ff
+ >;
+ };
+
+ pinctrl_leds_debug: pinctrl-leds-debug {
+ fsl,pins = <
+ VF610_PAD_PTD3__GPIO_82 0x31c2
+ VF610_PAD_PTE3__GPIO_108 0x31c2
+ VF610_PAD_PTE4__GPIO_109 0x31c2
+ VF610_PAD_PTE5__GPIO_110 0x31c2
+ VF610_PAD_PTE6__GPIO_111 0x31c2
+ >;
+ };
+
+ pinctrl_switch: switch-grp {
+ fsl,pins = <
+ VF610_PAD_PTB28__GPIO_98 0x3061
+ VF610_PAD_PTE2__GPIO_107 0x1042
+ >;
+ };
+
+ pinctrl_uart0: uart0grp {
+ fsl,pins = <
+ VF610_PAD_PTB10__UART0_TX 0x21a2
+ VF610_PAD_PTB11__UART0_RX 0x21a1
+ >;
+ };
+};
--
2.17.1
