On Fri, Jul 20, 2018 at 07:02:37PM +0530, Balakrishna Godavarthi wrote:
> This patch enables regulators for the Qualcomm Bluetooth wcn3990
> controller.
>
> Signed-off-by: Balakrishna Godavarthi <bgoda...@codeaurora.org>
> Reviewed-by: Rob Herring <r...@kernel.org>
> ---
> Changes in v10:
> * added entry for regulator currents
>
> Changes in v9:
> * updated with latest reg handle and names.
> * updated max-speed definition.
>
> Changes in v8:
> * Separated the optional entries between two chips
>
> Changes in v7:
> * no change.
>
> Changes in v6:
>
> * Changed the oper-speed to max-speed.
>
> Changes in v5:
>
> * Added entry for oper-speed and init-speed.
>
> ---
> .../bindings/net/qualcomm-bluetooth.txt | 42 ++++++++++++++++++-
> 1 file changed, 40 insertions(+), 2 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/net/qualcomm-bluetooth.txt
> b/Documentation/devicetree/bindings/net/qualcomm-bluetooth.txt
> index 0ea18a53cc29..ca04c4981048 100644
> --- a/Documentation/devicetree/bindings/net/qualcomm-bluetooth.txt
> +++ b/Documentation/devicetree/bindings/net/qualcomm-bluetooth.txt
> @@ -10,12 +10,34 @@ device the slave device is attached to.
> Required properties:
> - compatible: should contain one of the following:
> * "qcom,qca6174-bt"
> + * "qcom,wcn3990-bt"
> +
> +Optional properties for compatible string qcom,qca6174-bt:
>
> -Optional properties:
> - enable-gpios: gpio specifier used to enable chip
> - clocks: clock provided to the controller (SUSCLK_32KHZ)
>
> -Example:
> +Optional properties for compatible string qcom,wcn3990-bt:
> +
> + - vddio-supply: Bluetooth wcn3990 VDD_IO supply regulator handle.
> + - vddxo-supply: Bluetooth wcn3990 VDD_XO supply regulator handle.
> + - vddrf-supply: Bluetooth wcn3990 VDD_RF supply regulator handle.
> + - vddch0-supply: Bluetooth wcn3990 VDD_CH0 supply regulator handle.
> +
> + - If WCN3990 is connected to platform where RPMH PMIC processor is used
> + then the load values will be 1uA. if it is connected to platform where RPM
> + PMIC processor is used then load value will be 10000 uA.
> + if it is connected to different platform, where current values are fixed
> + as in data sheet then below property are not required.
Please provide details why these magic values are needed for RPMh and
RPM PMICs.
For RPMh it looks like a value of 1uA would cause the regulator to
enter idle mode:
static int rpmh_regulator_vrm_set_load(struct regulator_dev *rdev, int load_uA)
{
struct rpmh_vreg *vreg = rdev_get_drvdata(rdev);
unsigned int mode;
if (load_uA >= vreg->hw_data->hpm_min_load_uA)
mode = REGULATOR_MODE_NORMAL;
else
mode = REGULATOR_MODE_IDLE;
return rpmh_regulator_vrm_set_mode(rdev, mode);
}
https://patchwork.kernel.org/patch/10524299/
Is that really intended and if so why? It might make sense to save
power when really in idle mode, but I assume you somehow have to tell
the regulator to switch to normal mode when BT is used.
I also commented about this on patch "[7/7] Bluetooth: hci_qca: Add
support for Qualcomm Bluetooth chip wcn3990". I suggest to center the
discussion here and reply with a link to the other patch.
