On Fri, Sep 14, 2018 at 05:18:34PM -0700, Rajat Jain wrote:
> Hi,
>
> This is to report what I think is a problem in the pinctrl-icelake
> driver. It seems that when trying to control GPIO pins GPP_A* and
> GPIO_B*, the driver ends up writing to incorrect PADCFG registers.
> I've reached this conclusion by putting debug prints in the driver,
> although this can be seen by the following commands too. Please let me
> know if something is wrong in my experiments. For example, when trying
> to control GPP_B8/ISH_I2C1_SCL, the driver ends up writing to
> GPP_A6/ESPI_RESETB registers.
>
> I want to control the pin GPP_B8 i.e. ISH_I2C1_SCL and drive it low or
> high. I looked at the driver code, and it tells me that I need to use
> pin number 16:
>
> static const struct pinctrl_pin_desc icllp_pins[] = {
> ....
> /* GPP_B */
> ....
> PINCTRL_PIN(16, "ISH_I2C1_SCL"),
> .....
>
> The pin number 16 is mapped to GPIO 224 as per the below output:
>
> localhost /sys/class/gpio # cat
> /sys/kernel/debug/pinctrl/INT3455\:00/gpio-ranges
> GPIO ranges handled:
> 0: INT3455:00 GPIOS [184 - 191] PINS [0 - 7]
> 32: INT3455:00 GPIOS [216 - 241] PINS [8 - 33]
> 64: INT3455:00 GPIOS [248 - 272] PINS [34 - 58]
> 96: INT3455:00 GPIOS [280 - 303] PINS [59 - 82]
> 128: INT3455:00 GPIOS [312 - 332] PINS [83 - 103]
> 160: INT3455:00 GPIOS [344 - 363] PINS [104 - 123]
> 192: INT3455:00 GPIOS [376 - 404] PINS [124 - 152]
> 224: INT3455:00 GPIOS [408 - 431] PINS [153 - 176]
> 256: INT3455:00 GPIOS [440 - 463] PINS [183 - 206]
> 288: INT3455:00 GPIOS [472 - 479] PINS [216 - 223]
> 320: INT3455:00 GPIOS [504 - 511] PINS [224 - 231]
> localhost /sys/class/gpio #
>
> So I did this:
>
> localhost /sys/class/gpio # ls
> export gpiochip184 unexport
> localhost /sys/class/gpio # cat gpiochip184/label
> INT3455:00
> localhost /sys/class/gpio # cat gpiochip184/ngpio
> 328
> localhost /sys/class/gpio # echo 224 > export
> localhost /sys/class/gpio # ls
> export gpio224 gpiochip184 unexport
> localhost /sys/class/gpio #
>
> Before trying to change the value, I decided to take a dump of the
> PADCFG of the pins before and after I tried to change it. Here is the
> dump I took before changing:
>
> localhost /sys/class/gpio # cat gpio224/active_low
> 0
> localhost /sys/class/gpio # cat gpio224/direction
> in
> localhost /sys/class/gpio # cat gpio224/edge
> none
> localhost /sys/class/gpio # cat gpio224/value
> 0
> localhost /sys/class/gpio #
> localhost /sys/class/gpio # cat
> /sys/kernel/debug/pinctrl/INT3455\:00/pins | grep
> "ISH_I2C1_SCL\|ESPI_RESETB"
> pin 16 (ISH_I2C1_SCL) GPIO 0x44000102 0x00000028 0x00000000 [ACPI]
> pin 40 (ESPI_RESETB) mode 1 0x44000700 0x0000003e 0x00000100 [ACPI]
> localhost /sys/class/gpio #
>
> Here is when I tried to change it and then dump the values again:
>
> localhost /sys/class/gpio # echo out > gpio224/direction
> localhost /sys/class/gpio # cat
> /sys/kernel/debug/pinctrl/INT3455\:00/pins | grep
> "ISH_I2C1_SCL\|ESPI_RESETB"
> pin 16 (ISH_I2C1_SCL) GPIO 0x44000200 0x00000028 0x00000000 [ACPI]
> pin 40 (ESPI_RESETB) mode 1 0x44000700 0x0000003e 0x00000100 [ACPI]
> localhost /sys/class/gpio #
>
> Note that things look good so far (the PADCFG DW0 for pin 16 is
> corrrectly changed).
> But now when I try to write the value, it is the PADCFG DW0 for pin 40
> that gets written to, while the pin16 value does not change:
>
> localhost /sys/class/gpio #
> localhost /sys/class/gpio # echo 1 > gpio224/value
> localhost /sys/class/gpio # cat
> /sys/kernel/debug/pinctrl/INT3455\:00/pins | grep
> "ISH_I2C1_SCL\|ESPI_RESETB"
> pin 16 (ISH_I2C1_SCL) GPIO 0x44000200 0x00000028 0x00000000 [ACPI]
> pin 40 (ESPI_RESETB) mode 1 0x44000701 0x0000003e 0x00000100 [ACPI]
> localhost /sys/class/gpio #
> localhost /sys/class/gpio #
> localhost /sys/class/gpio # echo 0 > gpio224/value
> localhost /sys/class/gpio # cat
> /sys/kernel/debug/pinctrl/INT3455\:00/pins | grep
> "ISH_I2C1_SCL\|ESPI_RESETB"
> pin 16 (ISH_I2C1_SCL) GPIO 0x44000200 0x00000028 0x00000000 [ACPI]
> pin 40 (ESPI_RESETB) mode 1 0x44000700 0x0000003e 0x00000100 [ACPI]
> localhost /sys/class/gpio #
> localhost /sys/class/gpio # echo 1 > gpio224/value
> localhost /sys/class/gpio # cat
> /sys/kernel/debug/pinctrl/INT3455\:00/pins | grep
> "ISH_I2C1_SCL\|ESPI_RESETB"
> pin 16 (ISH_I2C1_SCL) GPIO 0x44000200 0x00000028 0x00000000 [ACPI]
> pin 40 (ESPI_RESETB) mode 1 0x44000701 0x0000003e 0x00000100 [ACPI]
> localhost /sys/class/gpio #
> localhost /sys/class/gpio #
>
> I have also verified this using an oscilloscope on the external pin
> that the ISH_I2C1_SCL does not change. Also the gpio224/value stays
> stuck at 0.
>
> localhost /sys/class/gpio # cat gpio224/value
> 0
> localhost /sys/class/gpio #
>
> I failed to understand how could it be that the correct pin (16) is
> picked up when setting direction but incorrect pin (40) is picked up
> when setting value. I suspect some mux related call is being missed
> out while setting the value, may be? Can you please check this at your
> end?
Do you have schematics of the system? It could be that the ISH_I2C1_SCL
is just pulled low.
Can you try some other pin that you could measure and is wired a pin
header?
