Once the boot CPU has been prepared or a new secondary CPU has been
brought up, use ICC_PMR_EL1 to mask interrupts on that CPU and clear
PSR.I bit.
Since ICC_PMR_EL1 is initialized at CPU bringup, avoid overwriting
it in the GICv3 driver.
Signed-off-by: Julien Thierry <julien.thie...@arm.com>
Suggested-by: Daniel Thompson <daniel.thomp...@linaro.org>
Cc: Catalin Marinas <catalin.mari...@arm.com>
Cc: Will Deacon <will.dea...@arm.com>
Cc: James Morse <james.mo...@arm.com>
Cc: Marc Zyngier <marc.zyng...@arm.com>
---
arch/arm64/kernel/smp.c | 27 +++++++++++++++++++++++++++
drivers/irqchip/irq-gic-v3.c | 8 +++++++-
2 files changed, 34 insertions(+), 1 deletion(-)
diff --git a/arch/arm64/kernel/smp.c b/arch/arm64/kernel/smp.c
index 8dc9dde..e495360 100644
--- a/arch/arm64/kernel/smp.c
+++ b/arch/arm64/kernel/smp.c
@@ -35,6 +35,7 @@
#include <linux/smp.h>
#include <linux/seq_file.h>
#include <linux/irq.h>
+#include <linux/irqchip/arm-gic-v3.h>
#include <linux/percpu.h>
#include <linux/clockchips.h>
#include <linux/completion.h>
@@ -175,6 +176,25 @@ int __cpu_up(unsigned int cpu, struct task_struct *idle)
return ret;
}
+static void init_gic_priority_masking(void)
+{
+ u32 gic_sre = gic_read_sre();
+ u32 cpuflags;
+
+ if (WARN_ON(!(gic_sre & ICC_SRE_EL1_SRE)))
+ return;
+
+ WARN_ON(!irqs_disabled());
+
+ gic_write_pmr(GIC_PRIO_IRQOFF);
+
+ cpuflags = read_sysreg(daif);
+
+ /* We can only unmask PSR.I if we can take aborts */
+ if (!(cpuflags & PSR_A_BIT))
+ write_sysreg(cpuflags & ~PSR_I_BIT, daif);
+}
+
/*
* This is the secondary CPU boot entry. We're using this CPUs
* idle thread stack, but a set of temporary page tables.
@@ -211,6 +231,9 @@ asmlinkage notrace void secondary_start_kernel(void)
*/
check_local_cpu_capabilities();
+ if (system_supports_irq_prio_masking())
+ init_gic_priority_masking();
+
if (cpu_ops[cpu]->cpu_postboot)
cpu_ops[cpu]->cpu_postboot();
@@ -421,6 +444,10 @@ void __init smp_prepare_boot_cpu(void)
* and/or scheduling is enabled.
*/
apply_boot_alternatives();
+
+ /* Conditionally switch to GIC PMR for interrupt masking */
+ if (system_supports_irq_prio_masking())
+ init_gic_priority_masking();
}
static u64 __init of_get_cpu_mpidr(struct device_node *dn)
diff --git a/drivers/irqchip/irq-gic-v3.c b/drivers/irqchip/irq-gic-v3.c
index dbf5247..7f0b2e8 100644
--- a/drivers/irqchip/irq-gic-v3.c
+++ b/drivers/irqchip/irq-gic-v3.c
@@ -414,6 +414,9 @@ static u32 gic_get_pribits(void)
static bool gic_has_group0(void)
{
u32 val;
+ u32 old_pmr;
+
+ old_pmr = gic_read_pmr();
/*
* Let's find out if Group0 is under control of EL3 or not by
@@ -429,6 +432,8 @@ static bool gic_has_group0(void)
gic_write_pmr(BIT(8 - gic_get_pribits()));
val = gic_read_pmr();
+ gic_write_pmr(old_pmr);
+
return val != 0;
}
@@ -590,7 +595,8 @@ static void gic_cpu_sys_reg_init(void)
group0 = gic_has_group0();
/* Set priority mask register */
- write_gicreg(DEFAULT_PMR_VALUE, ICC_PMR_EL1);
+ if (!gic_prio_masking_enabled())
+ write_gicreg(DEFAULT_PMR_VALUE, ICC_PMR_EL1);
/*
* Some firmwares hand over to the kernel with the BPR changed from
--
1.9.1
