On Tue, Oct 16, 2018 at 02:27:20PM +0900, Kunihiko Hayashi wrote:
> Add DT bindings for PCIe controller implemented in UniPhier SoCs when
> configured in Root Complex (host) mode. This controller is based on
> the DesignWare PCIe core.
>
> Signed-off-by: Kunihiko Hayashi <[email protected]>
> Reviewed-by: Rob Herring <[email protected]>
> ---
> .../devicetree/bindings/pci/uniphier-pcie.txt | 81
> ++++++++++++++++++++++
> 1 file changed, 81 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/pci/uniphier-pcie.txt
>
> diff --git a/Documentation/devicetree/bindings/pci/uniphier-pcie.txt
> b/Documentation/devicetree/bindings/pci/uniphier-pcie.txt
> new file mode 100644
> index 0000000..46a2754
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/pci/uniphier-pcie.txt
> @@ -0,0 +1,81 @@
> +Socionext UniPhier PCIe host controller bindings
> +
> +This describes the devicetree bindings for PCIe host controller implemented
> +on Socionext UniPhier SoCs.
> +
> +UniPhier PCIe host controller is based on the Synopsys DesignWare PCI core.
> +It shares common functions with the PCIe DesignWare core driver and inherits
> +common properties defined in
> +Documentation/devicetree/bindings/pci/designware-pcie.txt.
> +
> +Required properties:
> +- compatible: Should be "socionext,uniphier-pcie".
> +- reg: Specifies offset and length of the register set for the device.
> + According to the reg-names, appropriate register sets are required.
> +- reg-names: Must include the following entries:
> + "dbi" - controller configuration registers
> + "link" - SoC-specific glue layer registers
> + "config" - PCIe configuration space
> +- clocks: A phandle to the clock gate for PCIe glue layer including
> + the host controller.
> +- resets: A phandle to the reset line for PCIe glue layer including
> + the host controller.
> +- interrupts: A list of interrupt specifiers. According to the
> + interrupt-names, appropriate interrupts are required.
> +- interrupt-names: Must include the following entries:
> + "dma" - DMA interrupt
> + "msi" - MSI interrupt
> +
> +Optional properties:
> +- phys: A phandle to generic PCIe PHY. According to the phy-names,
> appropriate
> + phys are required.
> +- phy-names: Must be "pcie-phy".
> +
> +Required sub-node:
> +- legacy-interrupt-controller: Specifies interrupt controller for legacy PCI
> + interrupts.
> +
> +Required properties for legacy-interrupt-controller:
> +- interrupt-controller: identifies the node as an interrupt controller.
> +- #interrupt-cells: specifies the number of cells needed to encode an
> + interrupt source. The value must be 1.
> +- interrupt-parent: Phandle to the parent interrupt controller.
> +- interrupts: An interrupt specifier for legacy interrupt.
> +
> +Example:
> +
> + pcie: pcie@66000000 {
> + compatible = "socionext,uniphier-pcie", "snps,dw-pcie";
> + status = "disabled";
> + reg-names = "dbi", "link", "config";
> + reg = <0x66000000 0x1000>, <0x66010000 0x10000>,
> + <0x2fff0000 0x10000>;
> + #address-cells = <3>;
> + #size-cells = <2>;
> + clocks = <&sys_clk 24>;
> + resets = <&sys_rst 24>;
> + num-lanes = <1>;
> + num-viewport = <1>;
> + bus-range = <0x0 0xff>;
> + device_type = "pci";
> + ranges =
> + /* downstream I/O */
> + <0x81000000 0 0x00000000 0x2ffe0000 0 0x00010000
> + /* non-prefetchable memory */
> + 0x82000000 0 0x00000000 0x20000000 0 0x0ffe0000>;
> + #interrupt-cells = <1>;
> + interrupt-names = "dma", "msi";
> + interrupts = <0 224 4>, <0 225 4>;
> + interrupt-map-mask = <0 0 0 7>;
> + interrupt-map = <0 0 0 1 &pcie_intc 1>, /* INTA */
> + <0 0 0 2 &pcie_intc 2>, /* INTB */
> + <0 0 0 3 &pcie_intc 3>, /* INTC */
> + <0 0 0 4 &pcie_intc 4>; /* INTD */
This is not correct and we must fix this concept for all DWC based host
bridges bindings. We are mapping INTX to inputs [0,1,2,3] of the host
bridge interrupt controllers and the binding should reflect that.
This should be the correct mapping:
interrupt-map = <0 0 0 1 &pcie_intc 0>, /* INTA */
<0 0 0 2 &pcie_intc 1>, /* INTB */
<0 0 0 3 &pcie_intc 2>, /* INTC */
<0 0 0 4 &pcie_intc 3>; /* INTD */
Lorenzo
> +
> + pcie_intc: legacy-interrupt-controller {
> + interrupt-controller;
> + #interrupt-cells = <1>;
> + interrupt-parent = <&gic>;
> + interrupts = <0 226 4>;
> + };
> + };
> --
> 2.7.4
>
