Hi Stefan,
Thank you for the patch.
I have few nits below.
On 1/31/19 9:23 AM, Stefan Mavrodiev wrote:
This adds the devicetree bindings for charge led indicator found
on most of X-Powers AXP20X PMICs.
Signed-off-by: Stefan Mavrodiev <[email protected]>
---
.../devicetree/bindings/leds/leds-axp20x.txt | 74 +++++++++++++++++++
1 file changed, 74 insertions(+)
create mode 100644 Documentation/devicetree/bindings/leds/leds-axp20x.txt
diff --git a/Documentation/devicetree/bindings/leds/leds-axp20x.txt
b/Documentation/devicetree/bindings/leds/leds-axp20x.txt
new file mode 100644
index 000000000000..73fae22ffe29
--- /dev/null
+++ b/Documentation/devicetree/bindings/leds/leds-axp20x.txt
@@ -0,0 +1,74 @@
+Device Tree Bindings for LED support on X-Powers PMIC
+
+Most of the X-Powers PMICs have integrated battery charger with LED indicator.
+The output is open-drain, so the state is either high-Z or output-low. The
+driver is subnode of AXP20X MFD driver, since it uses shared bus with all
s/is subnode/is a subnode/
+other cells.
+The LED can be controlled either manually or automatic. Then in automatic
s/or automatic/or automatically/
+(controlled by the charger) there are two indication modes:
+
+Mode-A
+======
+- output-low: Charging
+- high-Z Not charging
+- 1Hz flashing: Abnormal alarm
+- 4Hz flashing Overvoltage alarm
+
+Mode-B
+======
+- output-low: Battery full
+- high-Z Not charging
+- 1Hz flashing: Charging
+- 4Hz flashing Overvoltage or abnormal alarm
+
+The control and the mode can be changed from sysfs.
+
+For AXP20X MFD bindings see:
+Documentation/devicetree/bindings/mfd/axp20x.txt
+
+Required properties:
+- compatible : Must be "x-powers,axp20x-led"
+
+Supported common leds properties, see ./common.txt for more information:
s/leds/LED/
Please remove ", see ./common.txt for more information" in favor
of references indicated below.
+- label : sets LED label. If omitted, dt device node is used
Please change it to:
- label : See Documentation/devicetree/bindings/leds/common.txt
+- linux,default-trigger : See
+- default-state:
- linux,default-trigger : See
Documentation/devicetree/bindings/leds/common.txt
+
+Optional properties:
+- x-powers,charger-mode: 0 for Mode-A, 1 for Mode-B
+ If omitted, then the control is set to manual mode.
+ On invalid value, Mode-A is used.
+
+
+Example:
+
+ axp803: pmic@3a3 {
+ compatible = "x-powers,axp803";
+
+ ...
+
+ axp20x-led {
s/axp20x-led/led@0/
+ compatible = "x-powers,axp20x-led";
+ status = "okay";
+
+ label = "axp20x:yellow:chgled";
+ linux,default-trigger = "timer";
+ default-state = "on";
+ };
+ };
+
+or
+
+ axp803: pmic@3a3 {
+ compatible = "x-powers,axp803";
+
+ ...
+
+ axp20x-led {
s/axp20x-led/led@0/
+ compatible = "x-powers,axp20x-led";
+ status = "okay";
+
+ label = "axp20x:yellow:chgled";
+ x-powers,charger-mode = "mode-b";
+ };
+ };
--
Best regards,
Jacek Anaszewski
