Tony,
On 04/02/19 20:00, Tony Lindgren wrote:
> * Roger Quadros <[email protected]> [190204 15:54]:
>> +static int sysc_enable_pruss(struct sysc *sysc)
>> +{
>> + int i;
>> + u32 reg;
>> + bool ready;
>> +
>> + /* configure for Smart Idle & Smart Standby */
>> + reg = sysc_read(sysc, sysc->offsets[SYSC_SYSCONFIG]);
>> + reg &= ~(SYSC_PRUSS_STANDBY_MASK | SYSC_PRUSS_IDLE_MASK);
>> + reg |= SYSC_PRUSS_STANDBY_SMART | SYSC_IDLE_SMART;
>> + sysc_write(sysc, sysc->offsets[SYSC_SYSCONFIG], reg);
>
> I think you can get rid of the SYSC_PRUSS_ defines here
> if you define the bits for it in struct sysc_regbits. The
> idle modes are SYSC_IDLE_* defines we already have in
> include/dt-bindings/bus/ti-sysc.h.
>
> My guess is these will just become generic sysc_enable()
> and sysc_disable() functions :)
>
> If you need module specific handling, you could add function
> pointers for enable and disable to struct sysc_capabilities.
OK. I'll move all this to a generic handler then.
>
>> @@ -649,6 +693,9 @@ static int __maybe_unused sysc_runtime_suspend(struct
>> device *dev)
>> goto idled;
>> }
>>
>> + if (ddata->cap->type == TI_SYSC_PRUSS)
>> + sysc_disable_pruss(ddata);
>> +
>> for (i = 0; i < ddata->nr_clocks; i++) {
>> if (IS_ERR_OR_NULL(ddata->clocks[i]))
>> continue;
>
> Ideally this would be just unconditional call to generic
> sysc_disable() here for non-legacy mode. Then if module
> specific enable and disable are there, sysc_enable() and
> disable() can call them.
OK.
>
>> +static const struct sysc_regbits sysc_regbits_pruss = {
>> + .midle_shift = -ENODEV,
>> + .clkact_shift = -ENODEV,
>> + .sidle_shift = -ENODEV,
>> + .enwkup_shift = -ENODEV,
>> + .srst_shift = -ENODEV,
>> + .autoidle_shift = -ENODEV,
>> + .dmadisable_shift = -ENODEV,
>> + .emufree_shift = -ENODEV,
>> +};
>
> So it seems you should populate at least midle_shift and sidle_shift
> bits here as in PRUSS_SYSCFG. I think STANDBY_MODE offset should go
> into the .midle_shift as it mentions initiator in TRM, and IDLE_MODE
> offset should go into .sidle_shift. So this might be really just using
> sysc_regbits_omap4_simple except it has an additional STANDBY_INIT
> bit which you could add for struct sysc_regbits if we don't have
> something similar already.
Got it.
>
>> @@ -1702,6 +1772,10 @@ static int sysc_probe(struct platform_device *pdev)
>>
>> INIT_DELAYED_WORK(&ddata->idle_work, ti_sysc_idle);
>>
>> + /* FIXME: how to ensure PRUSS stays enabled? */
>> + if (ddata->cap->type == TI_SYSC_PRUSS)
>> + goto skip_pm_put;
>> +
This was my bad. I forgot to move the pm_runtime_enable/get from the old
pruss_soc_bus.c to pruss.c :). It work after than and this hack is not required.
>> /* At least earlycon won't survive without deferred idle */
>> if (ddata->cfg.quirks & (SYSC_QUIRK_NO_IDLE_ON_INIT |
>> SYSC_QUIRK_NO_RESET_ON_INIT)) {
>
> Hmm so do you need to specify ti,no-idle-on-init or what's
> the logic needed here?
I was using "ti,no-reset-on-init" but that was because sysc_reset() was
returning error
due to missing syss mask. That can be fixed like so.
diff --git a/drivers/bus/ti-sysc.c b/drivers/bus/ti-sysc.c
index 5b9c81a..f5f2000 100644
--- a/drivers/bus/ti-sysc.c
+++ b/drivers/bus/ti-sysc.c
@@ -941,6 +941,7 @@ static int sysc_reset(struct sysc *ddata)
int val;
if (ddata->legacy_mode || offset < 0 ||
+ ddata->cap->regbits->srst_shift == -ENODEV ||
ddata->cfg.quirks & SYSC_QUIRK_NO_RESET_ON_INIT)
return 0;
>
>> diff --git a/include/dt-bindings/bus/ti-sysc.h
>> b/include/dt-bindings/bus/ti-sysc.h
>> index 8ec78e8..7138384 100644
>> --- a/include/dt-bindings/bus/ti-sysc.h
>> +++ b/include/dt-bindings/bus/ti-sysc.h
>> @@ -17,17 +17,6 @@
>>
>> #define SYSC_DRA7_MCAN_ENAWAKEUP (1 << 4)
>>
>> -/* SYSCONFIG specific to PRUSS */
>> -#define SYSC_PRUSS_SUB_MWAIT (1 << 5)
>> -#define SYSC_PRUSS_STANDBY_INIT (1 << 4)
>> -
>> -#define SYSC_PRUSS_STANDBY_FORCE (0 << 2)
>> -#define SYSC_PRUSS_STANDBY_NO (1 << 2)
>> -#define SYSC_PRUSS_STANDBY_SMART (2 << 2)
>> -#define SYSC_PRUSS_STANDBY_MASK (3 << 2)
>> -
>> -#define SYSC_PRUSS_IDLE_MASK 3
>> -
>> /* SYSCONFIG STANDBYMODE/MIDLEMODE/SIDLEMODE supported by hardware */
>> #define SYSC_IDLE_FORCE 0
>> #define SYSC_IDLE_NO 1
>
> I suggest you make this series independent of the
> rest of the PRUSS patches as we can add this
> separately. So no need to define these bits at all
> AFAIK.
OK. Thanks.
cheers,
-roger
>
> Regards,
>
> Tony
>
--
Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki.
Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki
