Add support for active discharge for USB power switches.
Signed-off-by: pascal paillet <[email protected]>
---
drivers/regulator/stpmic1_regulator.c | 68 ++++++++++++++++++++++++++++-------
1 file changed, 55 insertions(+), 13 deletions(-)
diff --git a/drivers/regulator/stpmic1_regulator.c
b/drivers/regulator/stpmic1_regulator.c
index 41128c4..f090614 100644
--- a/drivers/regulator/stpmic1_regulator.c
+++ b/drivers/regulator/stpmic1_regulator.c
@@ -177,11 +177,19 @@ enum {
.disable = regulator_disable_regmap,
};
+static const struct regulator_ops stpmic1_boost_regul_ops = {
+ .is_enabled = regulator_is_enabled_regmap,
+ .enable = regulator_enable_regmap,
+ .disable = regulator_disable_regmap,
+ .set_over_current_protection = stpmic1_set_icc,
+};
+
static const struct regulator_ops stpmic1_switch_regul_ops = {
.is_enabled = regulator_is_enabled_regmap,
.enable = regulator_enable_regmap,
.disable = regulator_disable_regmap,
.set_over_current_protection = stpmic1_set_icc,
+ .set_active_discharge = regulator_set_active_discharge_regmap,
};
#define REG_LDO(ids, base) { \
@@ -282,7 +290,44 @@ enum {
.supply_name = #base, \
}
-#define REG_SWITCH(ids, base, reg, mask, val) { \
+#define REG_BOOST(ids, base) { \
+ .name = #ids, \
+ .id = STPMIC1_##ids, \
+ .n_voltages = 1, \
+ .ops = &stpmic1_boost_regul_ops, \
+ .type = REGULATOR_VOLTAGE, \
+ .owner = THIS_MODULE, \
+ .min_uV = 0, \
+ .fixed_uV = 5000000, \
+ .enable_reg = BST_SW_CR, \
+ .enable_mask = BOOST_ENABLED, \
+ .enable_val = BOOST_ENABLED, \
+ .disable_val = 0, \
+ .enable_time = PMIC_ENABLE_TIME_US, \
+ .supply_name = #base, \
+}
+
+#define REG_VBUS_OTG(ids, base) { \
+ .name = #ids, \
+ .id = STPMIC1_##ids, \
+ .n_voltages = 1, \
+ .ops = &stpmic1_switch_regul_ops, \
+ .type = REGULATOR_VOLTAGE, \
+ .owner = THIS_MODULE, \
+ .min_uV = 0, \
+ .fixed_uV = 5000000, \
+ .enable_reg = BST_SW_CR, \
+ .enable_mask = USBSW_OTG_SWITCH_ENABLED, \
+ .enable_val = USBSW_OTG_SWITCH_ENABLED, \
+ .disable_val = 0, \
+ .enable_time = PMIC_ENABLE_TIME_US, \
+ .supply_name = #base, \
+ .active_discharge_reg = BST_SW_CR, \
+ .active_discharge_mask = VBUS_OTG_DISCHARGE, \
+ .active_discharge_on = VBUS_OTG_DISCHARGE, \
+}
+
+#define REG_SW_OUT(ids, base) { \
.name = #ids, \
.id = STPMIC1_##ids, \
.n_voltages = 1, \
@@ -291,12 +336,15 @@ enum {
.owner = THIS_MODULE, \
.min_uV = 0, \
.fixed_uV = 5000000, \
- .enable_reg = (reg), \
- .enable_mask = (mask), \
- .enable_val = (val), \
+ .enable_reg = BST_SW_CR, \
+ .enable_mask = SWIN_SWOUT_ENABLED, \
+ .enable_val = SWIN_SWOUT_ENABLED, \
.disable_val = 0, \
.enable_time = PMIC_ENABLE_TIME_US, \
.supply_name = #base, \
+ .active_discharge_reg = BST_SW_CR, \
+ .active_discharge_mask = SW_OUT_DISCHARGE, \
+ .active_discharge_on = SW_OUT_DISCHARGE, \
}
static const struct stpmic1_regulator_cfg stpmic1_regulator_cfgs[] = {
@@ -376,23 +424,17 @@ enum {
.mask_reset_mask = BIT(6),
},
[STPMIC1_BOOST] = {
- .desc = REG_SWITCH(BOOST, boost, BST_SW_CR,
- BOOST_ENABLED,
- BOOST_ENABLED),
+ .desc = REG_BOOST(BOOST, boost),
.icc_reg = BUCKS_ICCTO_CR,
.icc_mask = BIT(6),
},
[STPMIC1_VBUS_OTG] = {
- .desc = REG_SWITCH(VBUS_OTG, pwr_sw1, BST_SW_CR,
- USBSW_OTG_SWITCH_ENABLED,
- USBSW_OTG_SWITCH_ENABLED),
+ .desc = REG_VBUS_OTG(VBUS_OTG, pwr_sw1),
.icc_reg = BUCKS_ICCTO_CR,
.icc_mask = BIT(4),
},
[STPMIC1_SW_OUT] = {
- .desc = REG_SWITCH(SW_OUT, pwr_sw2, BST_SW_CR,
- SWIN_SWOUT_ENABLED,
- SWIN_SWOUT_ENABLED),
+ .desc = REG_SW_OUT(SW_OUT, pwr_sw2),
.icc_reg = BUCKS_ICCTO_CR,
.icc_mask = BIT(5),
},
--
1.9.1
