On Fri, Feb 15, 2019 at 01:50:08PM +0200, Stefan Mavrodiev wrote:
> This adds the devicetree bindings for charge led indicator found
> on most of X-Powers AXP20X PMICs.
>
> Signed-off-by: Stefan Mavrodiev <[email protected]>
> ---
> .../devicetree/bindings/leds/leds-axp20x.txt | 74 +++++++++++++++++++
> 1 file changed, 74 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/leds/leds-axp20x.txt
>
> diff --git a/Documentation/devicetree/bindings/leds/leds-axp20x.txt
> b/Documentation/devicetree/bindings/leds/leds-axp20x.txt
> new file mode 100644
> index 000000000000..5a83ad06796d
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/leds/leds-axp20x.txt
> @@ -0,0 +1,74 @@
> +Device Tree Bindings for LED support on X-Powers PMIC
> +
> +Most of the X-Powers PMICs have integrated battery charger with LED
> indicator.
> +The output is open-drain, so the state is either high-Z or output-low. The
> +driver is a subnode of AXP20X MFD driver, since it uses shared bus with all
> +other cells.
> +The LED can be controlled either manually or automatically. Then in automatic
> +(controlled by the charger) there are two indication modes:
> +
> +Mode-A
> +======
> +- output-low: Charging
> +- high-Z Not charging
> +- 1Hz flashing: Abnormal alarm
> +- 4Hz flashing Overvoltage alarm
> +
> +Mode-B
> +======
> +- output-low: Battery full
> +- high-Z Not charging
> +- 1Hz flashing: Charging
> +- 4Hz flashing Overvoltage or abnormal alarm
> +
> +The control and the mode can be changed from sysfs.
> +
> +For AXP20X MFD bindings see:
> +Documentation/devicetree/bindings/mfd/axp20x.txt
> +
> +Required properties:
> +- compatible : Must be "x-powers,axp20x-led"
> +
> +Supported common LED properties, see ./common.txt for more informationn
> +- label : See Documentation/devicetree/bindings/leds/common.txt
> +- linux,default-trigger : See
> Documentation/devicetree/bindings/leds/common.txt
> +- default-state: See Documentation/devicetree/bindings/leds/common.txt
> +
> +Optional properties:
> +- x-powers,charger-mode: 0 for Mode-A, 1 for Mode-B
> + If omitted, then the control is set to manual mode.
> + On invalid value, Mode-A is used.
> +
> +
> +Example:
> +
> + axp803: pmic@3a3 {
> + compatible = "x-powers,axp803";
> +
> + ...
> +
> + led@0 {
What's the 0 for? A unit address without a reg property is not valid.
> + compatible = "x-powers,axp20x-led";
> + status = "okay";
> +
> + label = "axp20x:yellow:chgled";
> + linux,default-trigger = "timer";
> + default-state = "on";
> + };
> + };
> +
> +or
> +
> + axp803: pmic@3a3 {
> + compatible = "x-powers,axp803";
> +
> + ...
> +
> + led@0 {
> + compatible = "x-powers,axp20x-led";
> + status = "okay";
> +
> + label = "axp20x:yellow:chgled";
> + x-powers,charger-mode = <1>;
> + };
> + };
> --
> 2.17.1
>
