- Adjust title markup;
- Adjust identation.
Signed-off-by: Mauro Carvalho Chehab <[email protected]>
---
.../{apds990x.txt => apds990x.rst} | 31 ++++++++++++++-----
Documentation/misc-devices/index.rst | 1 +
2 files changed, 25 insertions(+), 7 deletions(-)
rename Documentation/misc-devices/{apds990x.txt => apds990x.rst} (86%)
diff --git a/Documentation/misc-devices/apds990x.txt
b/Documentation/misc-devices/apds990x.rst
similarity index 86%
rename from Documentation/misc-devices/apds990x.txt
rename to Documentation/misc-devices/apds990x.rst
index 454d95d623b3..e2f75577f731 100644
--- a/Documentation/misc-devices/apds990x.txt
+++ b/Documentation/misc-devices/apds990x.rst
@@ -1,3 +1,6 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+======================
Kernel driver apds990x
======================
@@ -50,14 +53,18 @@ chip_id
power_state
RW - enable / disable chip. Uses counting logic
+
1 enables the chip
0 disables the chip
lux0_input
RO - measured lux value
+
sysfs_notify called when threshold interrupt occurs
lux0_sensor_range
- RO - lux0_input max value. Actually never reaches since sensor tends
+ RO - lux0_input max value.
+
+ Actually never reaches since sensor tends
to saturate much before that. Real max value varies depending
on the light spectrum etc.
@@ -68,7 +75,9 @@ lux0_rate_avail
RO - supported measurement rates
lux0_calibscale
- RW - calibration value. Set to neutral value by default.
+ RW - calibration value.
+
+ Set to neutral value by default.
Output results are multiplied with calibscale / calibscale_default
value.
@@ -76,16 +85,21 @@ lux0_calibscale_default
RO - neutral calibration value
lux0_thresh_above_value
- RW - HI level threshold value. All results above the value
+ RW - HI level threshold value.
+
+ All results above the value
trigs an interrupt. 65535 (i.e. sensor_range) disables the above
interrupt.
lux0_thresh_below_value
- RW - LO level threshold value. All results below the value
+ RW - LO level threshold value.
+
+ All results below the value
trigs an interrupt. 0 disables the below interrupt.
prox0_raw
RO - measured proximity value
+
sysfs_notify called when threshold interrupt occurs
prox0_sensor_range
@@ -93,11 +107,14 @@ prox0_sensor_range
prox0_raw_en
RW - enable / disable proximity - uses counting logic
- 1 enables the proximity
- 0 disables the proximity
+
+ - 1 enables the proximity
+ - 0 disables the proximity
prox0_reporting_mode
- RW - trigger / periodic. In "trigger" mode the driver tells two possible
+ RW - trigger / periodic.
+
+ In "trigger" mode the driver tells two possible
values: 0 or prox0_sensor_range value. 0 means no proximity,
1023 means proximity. This causes minimal number of interrupts.
In "periodic" mode the driver reports all values above
diff --git a/Documentation/misc-devices/index.rst
b/Documentation/misc-devices/index.rst
index d28e755a1595..a31c2ab8151f 100644
--- a/Documentation/misc-devices/index.rst
+++ b/Documentation/misc-devices/index.rst
@@ -15,6 +15,7 @@ fit into other categories.
:maxdepth: 2
ad525x_dpot
+ apds990x
bh1770glc
eeprom
c2port
--
2.25.4
