Hey Ben, On Thu, Aug 27, 2020 at 03:34:33PM +0000, Ben Levinsky wrote: > Hi Michael, > > Thanks for comment. Maybe I missed some of the comments then? I had thought > that your comments were the following and that I had answered them in the > code: > V8 3/5: > - zynqmp_pm_set_rpu_mode: pass arg1 instead of 0 to zynqmp_pm_invoke_fn > This should be reflected in v9 3/5 > - update kernel docs for zynqmp_pm_set_rpu_mode > may have misunderstood the comment here. I updated the function and its > comments above the function so that there is no obsolete iocl_id or arg2 > mentioned > V8 5/5: > - " In the event that zynqmp_r5_probe() fails before zynqmp_r5_setup_mbox() > has run, this will be called on an uninitialized skb_queue. (Also > obviously an issue once mailboxes are made optional again)." > To remedy this I added logic in v9 in the zynqmp_r5_release() function so > that the driver checks if a pointer field in the struct is NULL or no before > discarding skb's > > Were there other comments?
Yeah, there were a few others on v9, you can see the email here: https://lore.kernel.org/linux-remoteproc/[email protected]/T/#m1b326e5f059712dd33bee1bcd47e3c0ae245055e It looks like the first comment regarding the compilation failure due to the lack of linux/types.h was addressed in v10, but none of the subsequent comments; perhaps you just overlooked them? Thanks, Michael > > With that being said, I will make sure the R51 case is more completely > covered. > > Thanks > Ben > > > > -----Original Message----- > > From: Michael Auchter <[email protected]> > > Sent: Thursday, August 27, 2020 6:48 AM > > To: Ben Levinsky <[email protected]> > > Cc: Stefano Stabellini <[email protected]>; Michal Simek > > <[email protected]>; [email protected]; > > [email protected]; Ed T. Mooring <[email protected]>; linux- > > [email protected]; [email protected]; Jiaying Liang > > <[email protected]>; [email protected]; linux-arm- > > [email protected] > > Subject: Re: [PATCH v9 0/5] Provide basic driver to control Arm R5 co- > > processor found on Xilinx ZynqMP > > > > Hey Ben, > > > > On Wed, Aug 26, 2020 at 06:58:05PM -0700, Ben Levinsky wrote: > > > v10: > > > - add include types.h to xlnx-zynqmp.h for compilation > > > > I appreciate the quick turnaround on v10, but it looks like much of my > > feedback on v9 went unacknowledged. > > > > Most concerning is the fact that loading firmware on to R5 1 is _still_ > > broken in v10 due to the incorrect TCM banks being used. > > > > Thanks, > > Michael > > > > > > > > Ben Levinsky (5): > > > firmware: xilinx: Add ZynqMP firmware ioctl enums for RPU > > > configuration. > > > firmware: xilinx: Add shutdown/wakeup APIs > > > firmware: xilinx: Add RPU configuration APIs > > > dt-bindings: remoteproc: Add documentation for ZynqMP R5 rproc > > > bindings > > > remoteproc: Add initial zynqmp R5 remoteproc driver > > > > > > .../xilinx,zynqmp-r5-remoteproc.yaml | 113 +++ > > > drivers/firmware/xilinx/zynqmp.c | 86 ++ > > > drivers/remoteproc/Kconfig | 10 + > > > drivers/remoteproc/Makefile | 1 + > > > drivers/remoteproc/zynqmp_r5_remoteproc.c | 898 > > ++++++++++++++++++ > > > include/linux/firmware/xlnx-zynqmp.h | 63 ++ > > > 6 files changed, 1171 insertions(+) > > > create mode 100644 > > Documentation/devicetree/bindings/remoteproc/xilinx,zynqmp-r5- > > remoteproc.yaml > > > create mode 100644 drivers/remoteproc/zynqmp_r5_remoteproc.c > > > > > > -- > > > 2.17.1 > > >
