Hi Andrew,
Hi Len,

after booting 2.6.24-rc4-mm1 (2.6.24-rc4-190-g94545ba, otoh, boots just
fine) on my asus laptop, the machine reboots after claiming that
"Critical temperature reached (255 C)." However, the degrees number
is kinda hinting at 0xff all-ones field. Will try dump_stack in
acpi_thermal_critical() to checkout the call path. For now here's the 
netconsole bootlog:

[    0.000000] Linux version 2.6.24-rc4-mm1 ([EMAIL PROTECTED]) (gcc version 
4.2.3 20071123 (prerelease) (Debian 4.2.2-4)) #7 SMP PREEMPT Sun Dec 9 08:27:26 
CET 2007
[    0.000000] BIOS-provided physical RAM map:
[    0.000000]  BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[    0.000000]  BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[    0.000000]  BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[    0.000000]  BIOS-e820: 0000000000100000 - 000000001ff40000 (usable)
[    0.000000]  BIOS-e820: 000000001ff40000 - 000000001ff50000 (ACPI data)
[    0.000000]  BIOS-e820: 000000001ff50000 - 0000000020000000 (ACPI NVS)
[    0.000000] 511MB LOWMEM available.
[    0.000000] Zone PFN ranges:
[    0.000000]   DMA             0 ->     4096
[    0.000000]   Normal       4096 ->   130880
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[1] active PFN ranges
[    0.000000]     0:        0 ->   130880
[    0.000000] DMI 2.3 present.
[    0.000000] ACPI: RSDP 000F5DF0, 0014 (r0 ACPIAM)
[    0.000000] ACPI: RSDT 1FF40000, 002C (r1 A M I  OEMRSDT   6000423 MSFT      
 97)
[    0.000000] ACPI: FACP 1FF40200, 0081 (r1 A M I  OEMFACP   6000423 MSFT      
 97)
[    0.000000] ACPI: DSDT 1FF40400, 628D (r1  1ABSP 1ABSP001        1 MSFT  
2000001)
[    0.000000] ACPI: FACS 1FF50000, 0040
[    0.000000] ACPI: OEMB 1FF50040, 0053 (r1 A M I  OEMBIOS   6000423 MSFT      
 97)
[    0.000000] ACPI: PM-Timer IO Port: 0x408
[    0.000000] Allocating PCI resources starting at 30000000 (gap: 
20000000:e0000000)
[    0.000000] swsusp: Registered nosave memory region: 000000000009f000 - 
00000000000a0000
[    0.000000] swsusp: Registered nosave memory region: 00000000000a0000 - 
00000000000e0000
[    0.000000] swsusp: Registered nosave memory region: 00000000000e0000 - 
0000000000100000
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total 
pages: 129475
[    0.000000] Kernel command line: root=/dev/hda1 vga=0 nmi_watchdog=1 [EMAIL 
PROTECTED]/,@192.168.45.26/
[    0.000000] Found and enabled local APIC!
[    0.000000] Enabling fast FPU save and restore... done.
[    0.000000] Enabling unmasked SIMD FPU exception support... done.
[    0.000000] Initializing CPU#0
[    0.000000] CPU 0 irqstacks, hard=c0451000 soft=c0449000
[    0.000000] PID hash table entries: 2048 (order: 11, 8192 bytes)
[    0.000000] Detected 1500.114 MHz processor.
[   50.138075] Console: colour VGA+ 80x25
[   50.138080] console [tty0] enabled
[   50.140479] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[   50.140882] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[   50.160065] Memory: 513364k/523520k available (2049k kernel code, 9712k 
reserved, 1113k data, 172k init, 0k highmem)
[   50.160147] virtual kernel memory layout:
[   50.160148]     fixmap  : 0xfffb5000 - 0xfffff000   ( 296 kB)
[   50.160150]     vmalloc : 0xe0800000 - 0xfffb3000   ( 503 MB)
[   50.160151]     lowmem  : 0xc0000000 - 0xdff40000   ( 511 MB)
[   50.160153]       .init : 0xc041b000 - 0xc0446000   ( 172 kB)
[   50.160154]       .data : 0xc030067f - 0xc0416ca8   (1113 kB)
[   50.160156]       .text : 0xc0100000 - 0xc030067f   (2049 kB)
[   50.160549] Checking if this processor honours the WP bit even in supervisor 
mode... Ok.
[   50.160705] SLUB: Genslabs=11, HWalign=64, Order=0-1, MinObjects=4, CPUs=1, 
Nodes=1
[   50.220728] Calibrating delay using timer specific routine.. 3003.73 
BogoMIPS (lpj=1501865)
[   50.220857] Security Framework initialized
[   50.220934] Mount-cache hash table entries: 512
[   50.221174] CPU: L1 I cache: 32K, L1 D cache: 32K
[   50.221273] CPU: L2 cache: 1024K
[   50.221338] Intel machine check architecture supported.
[   50.221398] Intel machine check reporting enabled on CPU#0.
[   50.221459] Compat vDSO mapped to ffffe000.
[   50.221524] Checking 'hlt' instruction... OK.
[   50.225022] SMP alternatives: switching to UP code
[   50.225766] Freeing SMP alternatives: 11k freed
[   50.225823] ACPI: Core revision 20070126
[   50.229623] ACPI: setting ELCR to 0200 (from 0c30)
[   50.734915] CPU0: Intel(R) Pentium(R) M processor 1500MHz stepping 05
[   50.735059] SMP motherboard not detected.
[   50.836119] Brought up 1 CPUs
[   50.836305] khelper used greatest stack depth: 3352 bytes left
[   50.836463] net_namespace: 108 bytes
[   50.837167] NET: Registered protocol family 16
[   50.837466] ACPI: bus type pci registered
[   50.838812] PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=2
[   50.838872] PCI: Using configuration type 1
[   50.838928] Setting up standard PCI resources
[   50.850451] khelper used greatest stack depth: 3280 bytes left
[   50.851263] khelper used greatest stack depth: 3112 bytes left
[   50.857186] ACPI: EC: non-query interrupt received, switching to interrupt 
mode
[   50.858465] ACPI: Interpreter enabled
[   50.858524] ACPI: (supports S0 S3 S4 S5)
[   50.858760] ACPI: Using PIC for interrupt routing
[   50.868377] ACPI: EC: GPE = 0x1c, I/O: command/status = 0x66, data = 0x62
[   50.868445] ACPI: EC: driver started in interrupt mode
[   50.868555] ACPI: PCI Root Bridge [PCI0] (0000:00)
[   50.869056] PCI: Enabled i801 SMBus device
[   50.869117] PCI quirk: region 0400-047f claimed by ICH4 ACPI/GPIO/TCO
[   50.869179] PCI quirk: region 0500-053f claimed by ICH4 GPIO
[   50.869806] PCI: Transparent bridge - 0000:00:1e.0
[   50.873140] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12)
[   50.873851] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *11 12)
[   50.874535] ACPI: PCI Interrupt Link [LNKC] (IRQs *4 10 12)
[   50.875034] ACPI: PCI Interrupt Link [LNKD] (IRQs *5 6 10)
[   50.875537] ACPI: PCI Interrupt Link [LNKE] (IRQs 6 11) *0, disabled.
[   50.876080] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 7) *0, disabled.
[   50.876623] ACPI: PCI Interrupt Link [LNKG] (IRQs 4 7) *0, disabled.
[   50.877169] ACPI: PCI Interrupt Link [LNKH] (IRQs 4 6 *10 12)
[   50.877640] Linux Plug and Play Support v0.97 (c) Adam Belay
[   50.877738] pnp: PnP ACPI init
[   50.877803] ACPI: bus type pnp registered
[   50.883974] pnp: PnP ACPI: found 15 devices
[   50.884035] ACPI: ACPI bus type pnp unregistered
[   50.884094] PnPBIOS: Disabled by ACPI PNP
[   50.884329] usbcore: registered new interface driver usbfs
[   50.884441] usbcore: registered new interface driver hub
[   50.884552] usbcore: registered new device driver usb
[   50.884777] PCI: Using ACPI for IRQ routing
[   50.884834] PCI: If a device doesn't work, try "pci=routeirq".  If it helps, 
post a report
[   50.884927] PCI: Cannot allocate resource region 4 of device 0000:00:1f.3
[   50.893004] Time: tsc clocksource has been installed.
[   50.895050] system 00:09: ioport range 0x480-0x48f has been reserved
[   50.895112] system 00:09: ioport range 0x5c0-0x5cf has been reserved
[   50.895176] system 00:0a: ioport range 0x4d0-0x4d1 has been reserved
[   50.895242] system 00:0c: iomem range 0xffc00000-0xffefffff has been reserved
[   50.895309] system 00:0d: ioport range 0x540-0x55f has been reserved
[   50.895370] system 00:0d: ioport range 0x400-0x47f has been reserved
[   50.895435] system 00:0d: ioport range 0x480-0x48f has been reserved
[   50.895496] system 00:0d: ioport range 0x500-0x53f has been reserved
[   50.895557] system 00:0d: ioport range 0x4c0-0x4cf has been reserved
[   50.895617] system 00:0d: iomem range 0xfec00000-0xfec00fff has been reserved
[   50.895680] system 00:0d: iomem range 0xfee00000-0xfee00fff has been reserved
[   50.895746] system 00:0e: iomem range 0x0-0x9ffff could not be reserved
[   50.895807] system 00:0e: iomem range 0xc0000-0xdffff could not be reserved
[   50.895869] system 00:0e: iomem range 0xe0000-0xfffff could not be reserved
[   50.895931] system 00:0e: iomem range 0x100000-0x1fffffff could not be 
reserved
[   50.896004] system 00:0e: iomem range 0x0-0x0 could not be reserved
[   50.926541] PCI: Bridge: 0000:00:01.0
[   50.926598]   IO window: d000-dfff
[   50.926655]   MEM window: ff800000-ff8fffff
[   50.926713]   PREFETCH window: ce900000-de9fffff
[   50.926786] PCI: Bus 3, cardbus bridge: 0000:02:01.0
[   50.926843]   IO window: 00001400-000014ff
[   50.926901]   IO window: 00001800-000018ff
[   50.926960]   PREFETCH window: 34000000-37ffffff
[   50.927020]   MEM window: 38000000-3bffffff
[   50.927079] PCI: Bus 7, cardbus bridge: 0000:02:01.1
[   50.927136]   IO window: 00001c00-00001cff
[   50.927194]   IO window: 00002000-000020ff
[   50.927252]   PREFETCH window: 3c000000-3fffffff
[   50.927313]   MEM window: 40000000-43ffffff
[   50.927375] PCI: Bridge: 0000:00:1e.0
[   50.927430]   IO window: disabled.
[   50.927488]   MEM window: ff900000-ff9fffff
[   50.927547]   PREFETCH window: dea00000-deafffff
[   50.927631] PCI: Enabling device 0000:02:01.0 (0000 -> 0003)
[   50.927999] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
[   50.928064] ACPI: PCI Interrupt 0000:02:01.0[A] -> Link [LNKB] -> GSI 11 
(level, low) -> IRQ 11
[   50.928527] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
[   50.928587] ACPI: PCI Interrupt 0000:02:01.1[B] -> Link [LNKA] -> GSI 11 
(level, low) -> IRQ 11
[   50.928756] NET: Registered protocol family 2
[   50.937028] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[   50.937394] TCP established hash table entries: 16384 (order: 5, 131072 
bytes)
[   50.937603] TCP bind hash table entries: 16384 (order: 6, 393216 bytes)
[   50.938109] TCP: Hash tables configured (established 16384 bind 16384)
[   50.938171] TCP reno registered
[   50.943908] khelper used greatest stack depth: 3100 bytes left
[   50.945348] Installing knfsd (copyright (C) 1996 [EMAIL PROTECTED]).
[   50.945635] io scheduler noop registered (default)
[   50.946705] ACPI: AC Adapter [AC] (on-line)
[   50.947312] ACPI: Battery Slot [BAT0] (battery absent)
[   50.947441] ACPI: Battery Slot [BAT1] (battery absent)
[   50.947808] input: Power Button (FF) as /class/input/input0
[   50.947869] ACPI: Power Button (FF) [PWRF]
[   50.948032] input: Lid Switch as /class/input/input1
[   50.948146] ACPI: Lid Switch [LID]
[   50.948294] input: Sleep Button (CM) as /class/input/input2
[   50.948359] ACPI: Sleep Button (CM) [SLPB]
[   50.948511] input: Power Button (CM) as /class/input/input3
[   50.948571] ACPI: Power Button (CM) [PWRB]
[   50.948749] ACPI: Invalid PBLK length [7]
[   50.949640] ACPI: CPU0 (power states: C1[C1] C2[C2])
[   50.962860] ACPI: Critical trip point
[   50.962918] Critical temperature reached (255 C), shutting down.
[   50.962988] ACPI: Thermal Zone [THRM] (255 C)
[   50.963137] Asus Laptop ACPI Extras version 0.30
[   50.963335]   M6N model detected, supported
[   50.964168] isapnp: Scanning for PnP cards...
[   51.320980] isapnp: No Plug & Play device found
[   51.358289] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing 
disabled
[   51.358586] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a NS16550A
[   51.359209] ACPI: PCI Interrupt 0000:00:1f.6[B] -> Link [LNKB] -> GSI 11 
(level, low) -> IRQ 11
[   51.359375] ACPI: PCI interrupt for device 0000:00:1f.6 disabled
[   51.359565] tg3.c:v3.86 (November 9, 2007)
[   51.359635] ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [LNKB] -> GSI 11 
(level, low) -> IRQ 11
[   51.388900] eth0: Tigon3 [partno(BCM95788A50) rev 3003 PHY(5705)] 
(PCI:33MHz:32-bit) 10/100/1000Base-T Ethernet 00:11:2f:00:71:33
[   51.389234] eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] WireSpeed[0] 
TSOcap[1]
[   51.389304] eth0: dma_rwctrl[763f0000] dma_mask[32-bit]
[   51.389386] netconsole: local port 6665
[   51.389442] netconsole: local IP 192.168.45.67
[   51.389500] netconsole: interface eth0
[   51.389555] netconsole: remote port 6666
[   51.389611] netconsole: remote IP 192.168.45.26
[   51.389669] netconsole: remote ethernet address ff:ff:ff:ff:ff:ff
[   51.389729] netconsole: device eth0 not up yet, forcing it
[   53.278349] tg3: eth0: Link is up at 100 Mbps, full duplex.
[   53.278409] tg3: eth0: Flow control is on for TX and on for RX.
[   53.281188] console [netcon0] enabled
[   53.293588] netconsole: network logging started
[   53.293647] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[   53.293720] ide: Assuming 33MHz system bus speed for PIO modes; override 
with idebus=xx
[   53.293894] ICH4: IDE controller (0x8086:0x24ca rev 0x03) at  PCI slot 
0000:00:1f.1
[   53.293971] PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
[   53.294419] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 4
[   53.294486] ACPI: PCI Interrupt 0000:00:1f.1[A] -> Link [LNKC] -> GSI 4 
(level, low) -> IRQ 4
[   53.294670] ICH4: not 100% native mode: will probe irqs later
[   53.294750]     ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, 
hdb:pio
[   53.294924]     ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, 
hdd:pio
[   54.169666] hda: IC25N060ATMR04-0, ATA DISK drive
[   55.503664] hdc: TOSHIBA ODD-DVD SD-R6372, ATAPI CD/DVD-ROM drive
[   55.504886] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[   55.527065] ide1 at 0x170-0x177,0x376 on irq 15
[   55.538103] hda: max request size: 512KiB
[   55.538432] hda: 117210240 sectors (60011 MB) w/7884KiB Cache, 
CHS=16383/255/63, UDMA(100)
[   55.539013] hda: cache flushes supported
[   55.539119]  hda: hda1 hda2 hda3
[   55.553931] hdc: ATAPI 24X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, 
UDMA(33)
[   55.554381] Uniform CD-ROM driver Revision: 3.20
[   55.560575] ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 10
[   55.560642] ACPI: PCI Interrupt 0000:00:1d.7[D] -> Link [LNKH] -> GSI 10 
(level, low) -> IRQ 10
[   55.560836] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[   55.560974] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus 
number 1
[   55.564994] ehci_hcd 0000:00:1d.7: debug port 1
[   55.565074] ehci_hcd 0000:00:1d.7: irq 10, io mem 0xffaffc00
[   55.574449] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 
2004
[   55.574763] usb usb1: configuration #1 chosen from 1 choice
[   55.574888] hub 1-0:1.0: USB hub found
[   55.574951] hub 1-0:1.0: 6 ports detected
[   55.675460] usb usb1: New USB device found, idVendor=0000, idProduct=0000
[   55.675523] usb usb1: New USB device strings: Mfr=3, Product=2, 
SerialNumber=1
[   55.675606] usb usb1: Product: EHCI Host Controller
[   55.675664] usb usb1: Manufacturer: Linux 2.6.24-rc4-mm1 ehci_hcd
[   55.675735] usb usb1: SerialNumber: 0000:00:1d.7
[   55.830303] usbcore: registered new interface driver usbserial
[   55.830365] drivers/usb/serial/usb-serial.c: USB Serial Driver core
[   55.830476] drivers/usb/serial/usb-serial.c: USB Serial support registered 
for Keyspan - (without firmware)
[   55.830595] drivers/usb/serial/usb-serial.c: USB Serial support registered 
for Keyspan 1 port adapter
[   55.830714] drivers/usb/serial/usb-serial.c: USB Serial support registered 
for Keyspan 2 port adapter
[   55.830835] drivers/usb/serial/usb-serial.c: USB Serial support registered 
for Keyspan 4 port adapter
[   55.830961] usbcore: registered new interface driver keyspan
[   55.831022] drivers/usb/serial/keyspan.c: v1.1.5:Keyspan USB to Serial 
Converter Driver
[   55.831212] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f12:PS2M] at 0x60,0x64 
irq 1,12
[   55.833451] i8042.c: Detected active multiplexing controller, rev 1.1.
[   55.835365] serio: i8042 KBD port at 0x60,0x64 irq 1
[   55.835428] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[   55.835498] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[   55.835559] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[   55.835629] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[   55.835866] mice: PS/2 mouse device common for all mice
[   55.836284] cpuidle: using governor ladder
[   55.951618] input: AT Translated Set 2 keyboard as /class/input/input4
[   56.836635] cpuidle: using governor menu
[   56.836763] Advanced Linux Sound Architecture Driver Version 1.0.15 (Tue Nov 
20 19:16:42 2007 UTC).
[   56.836955] ACPI: PCI Interrupt 0000:00:1f.5[B] -> Link [LNKB] -> GSI 11 
(level, low) -> IRQ 11
[   56.838502] Marking TSC unstable due to: TSC halts in idle.
[   56.838572] Time: acpi_pm clocksource has been installed.
[   57.646804] intel8x0_measure_ac97_clock: measured 50509 usecs
[   57.646867] intel8x0: clocking to 48000
[   57.647364] ALSA device list:
[   57.647421]   #0: Intel 82801DB-ICH4 with STAC9750,51 at irq 11
[   57.647552] TCP cubic registered
[   57.647648] NET: Registered protocol family 1
[   57.647738] NET: Registered protocol family 17
[   57.647988] RPC: Registered udp transport module.
[   57.648048] RPC: Registered tcp transport module.
[   57.648200] Testing NMI watchdog ... OK.
[   57.668313] Using IPI No-Shortcut mode
[   57.733562] kjournald starting.  Commit interval 5 seconds
[   57.733643] EXT3-fs: mounted filesystem with ordered data mode.
[   57.733729] VFS: Mounted root (ext3 filesystem) readonly.
[   57.733969] Freeing unused kernel memory: 172k freed
[   57.800235] khelper used greatest stack depth: 2648 bytes left
[   58.980087] stty used greatest stack depth: 2640 bytes left
[   59.600742] mount used greatest stack depth: 2140 bytes left
[   60.959463] ACPI: Critical trip point
[   60.959542] Critical temperature reached (255 C), shutting down.
[   62.925991] Real Time Clock Driver v1.12ac
[   63.082557] Linux agpgart interface v0.103
[   63.128504] agpgart: suspend/resume problematic: resume with 3D/DRI active 
may lockup X.Org
[   63.128508] on some chipset/BIOS combos (see DEBUG_AGP_PM in intel-agp.c)
[   63.128718] agpgart: Detected an Intel 855PM Chipset.
[   63.143091] agpgart: AGP aperture is 256M @ 0xe0000000
[   63.166109] USB Universal Host Controller Interface driver v3.0
[   63.166282] ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [LNKA] -> GSI 11 
(level, low) -> IRQ 11
[   63.166490] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[   63.166607] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus 
number 2
[   63.167403] uhci_hcd 0000:00:1d.0: irq 11, io base 0x0000e800
[   63.167652] usb usb2: configuration #1 chosen from 1 choice
[   63.167757] hub 2-0:1.0: USB hub found
[   63.167820] hub 2-0:1.0: 2 ports detected
[   63.237339] Shutdown: hda
[   63.268462] usb usb2: New USB device found, idVendor=0000, idProduct=0000
[   63.268537] usb usb2: New USB device strings: Mfr=3, Product=2, 
SerialNumber=1
[   63.268629] usb usb2: Product: UHCI Host Controller
[   63.268687] usb usb2: Manufacturer: Linux 2.6.24-rc4-mm1 uhci_hcd
[   63.268760] usb usb2: SerialNumber: 0000:00:1d.0
[   63.269225] ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 5
[   63.269292] ACPI: PCI Interrupt 0000:00:1d.1[B] -> Link [LNKD] -> GSI 5 
(level, low) -> IRQ 5
[   63.269496] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[   63.269603] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus 
number 3
[   63.269709] uhci_hcd 0000:00:1d.1: irq 5, io base 0x0000e880
[   63.269944] usb usb3: configuration #1 chosen from 1 choice
[   63.270049] hub 3-0:1.0: USB hub found
[   63.270111] hub 3-0:1.0: 2 ports detected
[   63.370377] usb usb3: New USB device found, idVendor=0000, idProduct=0000
[   63.370450] usb usb3: New USB device strings: Mfr=3, Product=2, 
SerialNumber=1
[   63.370536] usb usb3: Product: UHCI Host Controller
[   63.370595] usb usb3: Manufacturer: Linux 2.6.24-rc4-mm1 uhci_hcd
[   63.370667] usb usb3: SerialNumber: 0000:00:1d.1
[   63.370772] ACPI: PCI Interrupt 0000:00:1d.2[C] -> Link [LNKC] -> GSI 4 
(level, low) -> IRQ 4
[   63.370967] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[   63.371072] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus 
number 4
[   63.371177] uhci_hcd 0000:00:1d.2: irq 4, io base 0x0000ec00
[   63.371413] usb usb4: configuration #1 chosen from 1 choice
[   63.371517] hub 4-0:1.0: USB hub found
[   63.371579] hub 4-0:1.0: 2 ports detected
[   63.472261] usb usb4: New USB device found, idVendor=0000, idProduct=0000
[   63.472325] usb usb4: New USB device strings: Mfr=3, Product=2, 
SerialNumber=1
[   63.472409] usb usb4: Product: UHCI Host Controller
[   63.472467] usb usb4: Manufacturer: Linux 2.6.24-rc4-mm1 uhci_hcd
[   63.472540] usb usb4: SerialNumber: 0000:00:1d.2
[   63.475203] usb 2-2: new low speed USB device using uhci_hcd and address 2
[   63.639154] usb 2-2: configuration #1 chosen from 1 choice
[   63.642112] usb 2-2: New USB device found, idVendor=046d, idProduct=c016
[   63.642176] usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[   63.642253] usb 2-2: Product: Optical USB Mouse
[   63.642311] usb 2-2: Manufacturer: Logitech
[   63.709809] Disabling non-boot CPUs ...
[   63.709884] Power down.
[   63.709944] acpi_power_off called
-- 
Regards/Gruß,
    Boris.

Attachment: config-2.6.24-rc4-mm1.bz2
Description: Binary data

Reply via email to