On 11/19/20 6:56 PM, Peter Ujfalusi wrote:
> It is used to control several SOM level muxes to make sure that the correct
> signals are routed to the correct pin on the SOM <-> CPB connectors.
>
> Signed-off-by: Peter Ujfalusi <peter.ujfal...@ti.com>
> ---
Yes, there is indeed a I2C GPIO expander on SOM that's missing from DT
today. So this change looks good to me.
Reviewed-by: Vignesh Raghavendra <vigne...@ti.com>
Regards
Vignesh
> .../dts/ti/k3-j7200-common-proc-board.dts | 11 --------
> arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi | 26 +++++++++++++++++++
> 2 files changed, 26 insertions(+), 11 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
> b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
> index 6b3863108571..2721137d8943 100644
> --- a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
> +++ b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
> @@ -43,13 +43,6 @@ J721E_WKUP_IOPAD(0x0098, PIN_INPUT, 0) /* (L4)
> MCU_MDIO0_MDIO */
> };
>
> &main_pmx0 {
> - main_i2c0_pins_default: main-i2c0-pins-default {
> - pinctrl-single,pins = <
> - J721E_IOPAD(0xd4, PIN_INPUT_PULLUP, 0) /* (V3) I2C0_SCL
> */
> - J721E_IOPAD(0xd8, PIN_INPUT_PULLUP, 0) /* (W2) I2C0_SDA
> */
> - >;
> - };
> -
> main_i2c1_pins_default: main-i2c1-pins-default {
> pinctrl-single,pins = <
> J721E_IOPAD(0xdc, PIN_INPUT_PULLUP, 3) /* (U3)
> ECAP0_IN_APWM_OUT.I2C1_SCL */
> @@ -146,10 +139,6 @@ &cpsw_port1 {
> };
>
> &main_i2c0 {
> - pinctrl-names = "default";
> - pinctrl-0 = <&main_i2c0_pins_default>;
> - clock-frequency = <400000>;
> -
> exp1: gpio@20 {
> compatible = "ti,tca6416";
> reg = <0x20>;
> diff --git a/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi
> b/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi
> index fbd17d38f6b6..7b5e9aa0324e 100644
> --- a/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi
> @@ -48,6 +48,15 @@ J721E_WKUP_IOPAD(0x28, PIN_INPUT, 1) /* (A7)
> MCU_OSPI0_D7.MCU_HYPERBUS0_DQ7 */
> };
> };
>
> +&main_pmx0 {
> + main_i2c0_pins_default: main-i2c0-pins-default {
> + pinctrl-single,pins = <
> + J721E_IOPAD(0xd4, PIN_INPUT_PULLUP, 0) /* (V3) I2C0_SCL
> */
> + J721E_IOPAD(0xd8, PIN_INPUT_PULLUP, 0) /* (W2) I2C0_SDA
> */
> + >;
> + };
> +};
> +
> &hbmc {
> /* OSPI and HBMC are muxed inside FSS, Bootloader will enable
> * appropriate node based on board detection
> @@ -131,3 +140,20 @@ &mailbox0_cluster10 {
> &mailbox0_cluster11 {
> status = "disabled";
> };
> +
> +&main_i2c0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&main_i2c0_pins_default>;
> + clock-frequency = <400000>;
> +
> + exp_som: gpio@21 {
> + compatible = "ti,tca6408";
> + reg = <0x21>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + gpio-line-names = "USB2.0_MUX_SEL", "CANUART_MUX1_SEL0",
> + "CANUART_MUX2_SEL0", "CANUART_MUX_SEL1",
> + "UART/LIN_MUX_SEL",
> "TRC_D17/AUDIO_REFCLK_SEL",
> + "GPIO_LIN_EN", "CAN_STB";
> + };
> +};
>
