Hi all,
This patch series implement a new dirty log tracking method for vfio dma.
Intention：
As we know, vfio live migration is an important and valuable feature, but there
are still many hurdles to solve, including migration of interrupt, device state,
DMA dirty log tracking, and etc.
For now, the only dirty log tracking interface is pinning. It has some
drawbacks:
1. Only smart vendor drivers are aware of this.
2. It's coarse-grained, the pinned-scope is generally bigger than what the
device actually access.
3. It can't track dirty continuously and precisely, vfio populates all
pinned-scope as dirty.
So it doesn't work well with iteratively dirty log handling.
About SMMU HTTU:
HTTU (Hardware Translation Table Update) is a feature of ARM SMMUv3, it can
update
access flag or/and dirty state of the TTD (Translation Table Descriptor) by
hardware.
With HTTU, stage1 TTD is classified into 3 types:
DBM bit AP[2](readonly bit)
1. writable_clean 1 1
2. writable_dirty 1 0
3. readonly 0 1
If HTTU_HD (manage dirty state) is enabled, smmu can change TTD from
writable_clean to
writable_dirty. Then software can scan TTD to sync dirty state into dirty
bitmap. With
this feature, we can track the dirty log of DMA continuously and precisely.
About this series:
Patch 1-3: Add feature detection for smmu HTTU and enable HTTU for smmu stage1
mapping.
And add feature detection for smmu BBML. We need to split block
mapping when
start dirty log tracking and merge page mapping when stop dirty log
tracking,
which requires break-before-make procedure. But it might
cause problems when the
TTD is alive. The I/O streams might not tolerate translation
faults. So BBML
should be used.
Patch 4-7: Add four interfaces (split_block, merge_page, sync_dirty_log and
clear_dirty_log)
in IOMMU layer, they are essential to implement dma dirty log
tracking for vfio.
We implement these interfaces for arm smmuv3.
Patch 8: Add HWDBM (Hardware Dirty Bit Management) device feature reporting
in IOMMU layer.
Patch9-11: Implement a new dirty log tracking method for vfio based on iommu
hwdbm. A new
ioctl operation named VFIO_DIRTY_LOG_MANUAL_CLEAR is added, which
can eliminate
some redundant dirty handling of userspace.
Optimizations TO Do:
1. We recognized that each smmu_domain (a vfio_container may has several
smmu_domain) has its
own stage1 mapping, and we must scan all these mapping to sync dirty state.
We plan to refactor
smmu_domain to support more than one smmu in one smmu_domain, then these
smmus can share a same
stage1 mapping.
2. We also recognized that scan TTD is a hotspot of performance. Recently, I
have implement a
SW/HW conbined dirty log tracking at MMU side [1], which can effectively
solve this problem.
This idea can be applied to smmu side too.
Thanks,
Keqian
[1]
https://lore.kernel.org/linux-arm-kernel/[email protected]/
jiangkunkun (11):
iommu/arm-smmu-v3: Add feature detection for HTTU
iommu/arm-smmu-v3: Enable HTTU for SMMU stage1 mapping
iommu/arm-smmu-v3: Add feature detection for BBML
iommu/arm-smmu-v3: Split block descriptor to a span of page
iommu/arm-smmu-v3: Merge a span of page to block descriptor
iommu/arm-smmu-v3: Scan leaf TTD to sync hardware dirty log
iommu/arm-smmu-v3: Clear dirty log according to bitmap
iommu/arm-smmu-v3: Add HWDBM device feature reporting
vfio/iommu_type1: Add HWDBM status maintanance
vfio/iommu_type1: Optimize dirty bitmap population based on iommu
HWDBM
vfio/iommu_type1: Add support for manual dirty log clear
drivers/iommu/arm/arm-smmu-v3/arm-smmu-v3.c | 138 ++++++-
drivers/iommu/arm/arm-smmu-v3/arm-smmu-v3.h | 14 +
drivers/iommu/io-pgtable-arm.c | 392 +++++++++++++++++++-
drivers/iommu/iommu.c | 227 ++++++++++++
drivers/vfio/vfio_iommu_type1.c | 235 +++++++++++-
include/linux/io-pgtable.h | 14 +
include/linux/iommu.h | 55 +++
include/uapi/linux/vfio.h | 28 +-
8 files changed, 1093 insertions(+), 10 deletions(-)
--
2.19.1
