On Tue, Aug 12, 2025 at 11:23:17AM +0200, Paolo Abeni wrote:
> On 8/5/25 11:46 AM, Hangbin Liu wrote:
> @@ -0,0 +1,95 @@
> > +#!/bin/bash
> > +# SPDX-License-Identifier: GPL-2.0
> > +#
> > +# Test if a bond interface works with lacp_active=off.
> > +
> > +# shellcheck disable=SC2034
> > +REQUIRE_MZ=no
> > +NUM_NETIFS=0
> > +lib_dir=$(dirname "$0")
> > +# shellcheck disable=SC1091
> > +source "$lib_dir"/../../../net/forwarding/lib.sh
> > +
> > +check_port_state()
> > +{
> > + local netns=$1
> > + local port=$2
> > + local state=$3
> > +
> > + ip -n "${netns}" -d -j link show "$port" | \
> > + jq -e
> > ".[].linkinfo.info_slave_data.ad_actor_oper_port_state_str |
> > index(\"${state}\") != null" > /dev/null
> > +}
> > +
> > +trap cleanup EXIT
> > +setup_ns c_ns s_ns
> > +defer cleanup_all_ns
> > +
> > +# shellcheck disable=SC2154
> > +ip -n "${c_ns}" link add eth0 type veth peer name eth0 netns "${s_ns}"
> > +ip -n "${c_ns}" link add eth1 type veth peer name eth1 netns "${s_ns}"
> > +ip -n "${s_ns}" link set eth0 up
> > +ip -n "${s_ns}" link set eth1 up
> > +ip -n "${c_ns}" link add bond0 type bond mode 802.3ad lacp_active off
> > lacp_rate fast
> > +ip -n "${c_ns}" link set eth0 master bond0
> > +ip -n "${c_ns}" link set eth1 master bond0
> > +ip -n "${c_ns}" link set bond0 up
> > +
> > +# 1. The passive side shouldn't send LACPDU.
> > +RET=0
> > +client_mac=$(cmd_jq "ip -j -n ${c_ns} link show bond0" ".[].address")
> > +# Wait for the first LACPDU due to state change.
> > +sleep 5
> > +timeout 62 ip netns exec "${c_ns}" tcpdump --immediate-mode -c 1 -i eth0 \
> > + -nn -l -vvv ether proto 0x8809 2> /dev/null > /tmp/client_init.out
> > +grep -q "System $client_mac" /tmp/client_init.out && RET=1
> > +log_test "802.3ad" "init port pkt lacp_active off"
> > +
> > +# 2. The passive side should not have the 'active' flag.
> > +RET=0
> > +check_port_state "${c_ns}" "eth0" "active" && RET=1
> > +log_test "802.3ad" "port state lacp_active off"
> > +
> > +# Set up the switch side with active mode.
> > +ip -n "${s_ns}" link set eth0 down
> > +ip -n "${s_ns}" link set eth1 down
> > +ip -n "${s_ns}" link add bond0 type bond mode 802.3ad lacp_active on
> > lacp_rate fast
> > +ip -n "${s_ns}" link set eth0 master bond0
> > +ip -n "${s_ns}" link set eth1 master bond0
> > +ip -n "${s_ns}" link set bond0 up
> > +# Make sure the negotiation finished
> > +sleep 5
>
> Minor nit: I guess the above sleep time depends on some kernel constant,
> but it's not obvious to me if the minimum time is mandated by the RFC,
> nor how long is such interval.
We need to make sure the lacp negotiation finished. There is no definition
in IEEE standard.
>
> A comment explaining the rationale behind such sleep will help, and
> possibly a loop with smaller minimal wait and periodic checks for the
> expected condition up to a significantly higher timeout could make the
> test both faster on average and more robust.
I will use tc rules to catch pkts and see if we can reduce some time.
Thanks
Hangbin
