From: George Guo <[email protected]> Add loongarch.conf to configure QEMU's LoongArch virtual machine (VM) with a la464 CPU, enable the 8250 serial console, and set the kernel image to vmlinux.efi. Extend vmtest.sh to recognise loongarch64 as a supported target and map it to the 'loongarch' kernel arch name.
QEMU's LoongArch VM provides no ACPI tables and relies on FDT to describe hardware. Without 'earlycon' on the kernel command line, the FDT is not scanned for a console UART, no output reaches the console, and vmtest.sh's console log stays empty causing the test to always fail. Add 'earlycon' to KERNEL_CMDLINE in loongarch.conf. QEMU's LoongArch VM has no i8042 PS/2 controller. When PNP detection finds nothing, i8042_init() falls back to probing the ports directly. On LoongArch the I/O ports are memory-mapped, and the i8042 port addresses are not backed by any device on the VM, so i8042_flush() takes a page fault and the kernel panics: i8042: PNP: No PS/2 controller found. i8042: Probing ports directly. CPU 0 Unable to handle kernel paging request at virtual address ffff800000008064 ERA: i8042_flush+0x50/0x198 RA: i8042_init+0x2a8/0x35c Kernel panic - not syncing: Attempted to kill init! Disable SERIO_I8042 and its dependents (KEYBOARD_ATKBD, MOUSE_PS2) in the QEMU_KCONFIG fragment to prevent the driver from being built. All three options are scoped to loongarch.conf; no other architecture is affected. Wrap the QEMU invocation in run_qemu() with timeout(1) using a local time limit so the test always terminates, even when QEMU does not exit on its own. This is useful for every architecture; on LoongArch, for example, QEMU provides no EFI runtime services and machine_restart() falls through to an idle loop after kexec, so QEMU would never exit otherwise. Co-developed-by: Kexin Liu <[email protected]> Signed-off-by: Kexin Liu <[email protected]> Signed-off-by: George Guo <[email protected]> --- tools/testing/selftests/kho/loongarch.conf | 11 +++++++++++ tools/testing/selftests/kho/vmtest.sh | 22 +++++++++++++++------- 2 files changed, 26 insertions(+), 7 deletions(-) create mode 100644 tools/testing/selftests/kho/loongarch.conf diff --git a/tools/testing/selftests/kho/loongarch.conf b/tools/testing/selftests/kho/loongarch.conf new file mode 100644 index 000000000000..e45fe1014cf3 --- /dev/null +++ b/tools/testing/selftests/kho/loongarch.conf @@ -0,0 +1,11 @@ +QEMU_CMD="qemu-system-loongarch64 -M virt -cpu la464" +QEMU_KCONFIG=" +CONFIG_SERIAL_8250=y +CONFIG_SERIAL_8250_CONSOLE=y +CONFIG_SPARSEMEM_MANUAL=y +# CONFIG_KEYBOARD_ATKBD is not set +# CONFIG_MOUSE_PS2 is not set +# CONFIG_SERIO_I8042 is not set +" +KERNEL_IMAGE="vmlinux.efi" +KERNEL_CMDLINE="console=ttyS0 earlycon kho_scratch=16M,16M,16M" diff --git a/tools/testing/selftests/kho/vmtest.sh b/tools/testing/selftests/kho/vmtest.sh index 0014bd76e88d..de6aa59cf5a0 100755 --- a/tools/testing/selftests/kho/vmtest.sh +++ b/tools/testing/selftests/kho/vmtest.sh @@ -21,7 +21,7 @@ Options: -d) path to the kernel build directory -j) number of jobs for compilation, similar to -j in make -t) run test for target_arch, requires CROSS_COMPILE set - supported targets: aarch64, x86_64 + supported targets: aarch64, x86_64, loongarch64 -h) display this help EOF } @@ -111,12 +111,19 @@ function run_qemu() { cmdline="$cmdline kho=on panic=-1" - $qemu_cmd -m 1G -smp 2 -no-reboot -nographic -nodefaults \ - -accel kvm -accel hvf -accel tcg \ - -serial file:"$serial" \ - -append "$cmdline" \ - -kernel "$kernel" \ - -initrd "$initrd" + local qemu_args=( + -m 1G -smp 2 -no-reboot -nographic -nodefaults + -accel kvm -accel hvf -accel tcg + -serial file:"$serial" + -append "$cmdline" + -kernel "$kernel" + -initrd "$initrd" + ) + + # Bound the QEMU run so the test always terminates, even when QEMU + # does not exit on its own (e.g. no EFI runtime services after kexec). + local qemu_timeout=60 + timeout "$qemu_timeout" $qemu_cmd "${qemu_args[@]}" || true grep "KHO restore succeeded" "$serial" &> /dev/null || fail "KHO failed" } @@ -127,6 +134,7 @@ function target_to_arch() { case $target in aarch64) echo "arm64" ;; x86_64) echo "x86" ;; + loongarch64) echo "loongarch" ;; *) skip "architecture $target is not supported" esac } -- 2.53.0
