Now that bareudp allows BIG TCP too, run the same checks over bareudp as for vxlan and geneve.
bareudp only works in external mode, so attach the tunnel metadata to all packets sent through the device with a tc tunnel_key action on egress. The device uses ethertype ipv4 with multiproto, so that both IPv4 and IPv6 traffic can go through it. Its MTU does not account for the encapsulation, so lower it to leave room for the IPv6 and UDP headers, otherwise the encapsulated packets would be fragmented. Assisted-by: LLM Signed-off-by: Haishuang Yan <[email protected]> --- .../testing/selftests/net/big_tcp_tunnels.sh | 52 +++++++++++++++---- 1 file changed, 43 insertions(+), 9 deletions(-) diff --git a/tools/testing/selftests/net/big_tcp_tunnels.sh b/tools/testing/selftests/net/big_tcp_tunnels.sh index cc0875e52fb9..2c841b4b79a5 100755 --- a/tools/testing/selftests/net/big_tcp_tunnels.sh +++ b/tools/testing/selftests/net/big_tcp_tunnels.sh @@ -1,7 +1,7 @@ #!/usr/bin/env bash # SPDX-License-Identifier: GPL-2.0 # -# Testing for IPv4 and IPv6 BIG TCP over VXLAN and GENEVE tunnels. +# Testing for IPv4 and IPv6 BIG TCP over VXLAN, GENEVE and bareudp tunnels. source "$(dirname "$0")/lib.sh" @@ -53,6 +53,21 @@ setup() { DEFAULT_TCP_MIN_TSO_SEGS=$(ip netns exec "$CLIENT_NS" sysctl -n net.ipv4.tcp_min_tso_segs) } +# Create a bareudp device. bareudp only works in external mode: attach the +# tunnel metadata to all packets sent through the device. Its MTU does not +# account for the encapsulation either, so leave room for IPv6 and UDP +# headers. +# $1: netns, $2: device, $3: local underlay address, $4: remote one +setup_bareudp() { + ip -netns "$1" link add "$2" type bareudp \ + dstport 6635 ethertype ipv4 multiproto && + ip -netns "$1" link set "$2" mtu 1452 && + tc -netns "$1" qdisc add dev "$2" clsact && + tc -netns "$1" filter add dev "$2" egress matchall \ + action tunnel_key set src_ip "$3" dst_ip "$4" id 0 ttl 64 || + { echo "Failed to set up bareudp device $2" >&2; return 1; } +} + setup_tunnel() { if [ "$2" = 4 ]; then SERVER_IP="$SERVER_IP4" @@ -64,26 +79,40 @@ setup_tunnel() { echo "Setting up ${1^^} over IPv6, veth tx csum offload $3" fi - if [ "$1" = vxlan ]; then + case "$1" in + vxlan) ip -netns "$CLIENT_NS" link add tun0 type vxlan \ id 5001 remote "$SERVER_IP" local "$CLIENT_IP" dev link0 dstport 4789 - else + ;; + geneve) ip -netns "$CLIENT_NS" link add tun0 type geneve \ id 5001 remote "$SERVER_IP" - fi + ;; + bareudp) + setup_bareudp "$CLIENT_NS" tun0 "$CLIENT_IP" "$SERVER_IP" || + return 1 + ;; + esac ip -netns "$CLIENT_NS" link set tun0 up ip -netns "$CLIENT_NS" addr replace "$CLIENT_IP4_TUN/24" dev tun0 ip -netns "$CLIENT_NS" addr replace "$CLIENT_IP6_TUN/112" dev tun0 nodad ip -netns "$CLIENT_NS" link set tun0 \ gso_max_size 196608 gso_ipv4_max_size 196608 \ gro_max_size 196608 gro_ipv4_max_size 196608 - if [ "$1" = vxlan ]; then + case "$1" in + vxlan) ip -netns "$SERVER_NS" link add tun1 type vxlan \ id 5001 remote "$CLIENT_IP" local "$SERVER_IP" dev link1 dstport 4789 - else + ;; + geneve) ip -netns "$SERVER_NS" link add tun1 type geneve \ id 5001 remote "$CLIENT_IP" - fi + ;; + bareudp) + setup_bareudp "$SERVER_NS" tun1 "$SERVER_IP" "$CLIENT_IP" || + return 1 + ;; + esac ip -netns "$SERVER_NS" link set tun1 up ip -netns "$SERVER_NS" addr replace "$SERVER_IP4_TUN/24" dev tun1 ip -netns "$SERVER_NS" addr replace "$SERVER_IP6_TUN/112" dev tun1 nodad @@ -112,7 +141,7 @@ do_test() { local packets_threshold="$PACKETS_THRESHOLD" # When tx csum offload is off, software GSO is performed before passing the - # packet to veth. Check BIG TCP packets inside the VXLAN tunnel to verify + # packet to veth. Check BIG TCP packets inside the tunnel to verify # the software checksum path: if the checksum code is broken, these packets # will be dropped. if [ "$3" = on ]; then @@ -192,6 +221,11 @@ if ! iptables --version &> /dev/null; then exit "$ksft_skip" fi +if ! tc -V &> /dev/null; then + echo "SKIP: Could not run test without tc tool" + exit "$ksft_skip" +fi + if ! ethtool --version &> /dev/null; then echo "SKIP: Could not run test without ethtool tool" exit "$ksft_skip" @@ -205,7 +239,7 @@ fi WORKDIR=$(mktemp -d) trap cleanup EXIT setup -for tunnel in vxlan geneve; do +for tunnel in vxlan geneve bareudp; do for tun_family in 4 6; do for traffic_family in 4 6; do for csum_offload in on off; do -- 2.43.0
