I'm seeing a similar usb timeout message here
with an HP 5200C usb scanner, e.g:
usb_control/bulk_msg: timeout
usb_control/bulk_msg: timeout
usb_control/bulk_msg: timeout
My config:
AMD-K6 450 on ASUS P5 mb
256 MB RAM, Ali chipset
Red Hat 7.0 updated, kernel 2.4.1-ac8
jjs
John Cavan wrote:
> Hi,
>
> Just got a D-Link USB radio (R100) and I'm seeing lots of timeouts with
> it. I've seen this through the last few 2.4.1+ and -ac+ kernels.
>
> Current config:
>
> Dual P3-500 w/ 512mb of RAM
> Tyan Tiger 133 mobo with VIA chipset, onboard USB
> Kernel 2.4.1-ac9 compiled with egcs-1.1.2
>
> The only thing funky is that three devices are sharing an interrupt:
>
> CPU0 CPU1
> 0: 216690 219652 IO-APIC-edge timer
> 1: 3564 3816 IO-APIC-edge keyboard
> 2: 0 0 XT-PIC cascade
> 3: 7 20 IO-APIC-edge serial
> 5: 1017 1135 IO-APIC-level EMU10K1
> 8: 0 1 IO-APIC-edge rtc
> 11: 22978 22756 IO-APIC-level aic7xxx, eth0, usb-uhci
> 12: 64220 63272 IO-APIC-edge PS/2 Mouse
> 14: 12132 12810 IO-APIC-edge ide0
> 15: 3 10 IO-APIC-edge ide1
> NMI: 436327 436327
> LOC: 436151 436128
> ERR: 0
>
> The ethernet card is a 3Com 3c905, the SCSI card is Adaptec 7892B (19160
> card). No problems with either as far as I can tell, but one of these
> modules may not be playing nice with interrupt sharing.
>
> The messages:
>
> usb.c: registered new driver usbdevfs
> usb.c: registered new driver hub
> usb-uhci.c: $Revision: 1.251 $ time 17:33:47 Feb 9 2001
> usb-uhci.c: High bandwidth mode enabled
> usb-uhci.c: USB UHCI at I/O 0xd400, IRQ 11
> usb-uhci.c: Detected 2 ports
> usb.c: new USB bus registered, assigned bus number 1
> usb_control/bulk_msg: timeout
> usb.c: USB device not accepting new address=2 (error=-110)
> usb.c: USB device 3 (vend/prod 0x4b4/0x1002) is not claimed by any
> active driver.
> usb_control/bulk_msg: timeout
> usb.c: error getting string descriptor 0 (error=-110)
> usb_control/bulk_msg: timeout
> usb.c: error getting string descriptor 0 (error=-110)
> usb_control/bulk_msg: timeout
> usb.c: error getting string descriptor 0 (error=-110)
> usb_control/bulk_msg: timeout
> usb.c: error getting string descriptor 0 (error=-110)
> usb_control/bulk_msg: timeout
> usb_control/bulk_msg: timeout
> usb_control/bulk_msg: timeout
> usb_control/bulk_msg: timeout
> usb_control/bulk_msg: timeout
> -
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to [EMAIL PROTECTED]
> Please read the FAQ at http://www.tux.org/lkml/
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [EMAIL PROTECTED]
Please read the FAQ at http://www.tux.org/lkml/
