On Wed, Jan 30, 2013 at 02:30:47PM -0700, Troy Kisky wrote:
> On 1/30/2013 3:37 PM, Anson Huang wrote:
> >some of anatop's regulators(vppcpu, vddpu and vddsoc) have
> >register settings about LDO's step time, which will impact
> >the LDO ramp up speed, need to use set_voltage_time_sel
> >interface to add necessary delay everytime LDOs' voltage
> >is increased.
> >
> >offset 0x170:
> >bit [24-25]: vddcpu
> >bit [26-27]: vddpu
> >bit [28-29]: vddsoc
> >
> >field definition:
> >0'b00: 64 cycles of 24M clock;
> >0'b01: 128 cycles of 24M clock;
> >0'b02: 256 cycles of 24M clock;
> >0'b03: 512 cycles of 24M clock;
> >
> >Signed-off-by: Anson Huang <b20...@freescale.com>
> >---
> > drivers/regulator/anatop-regulator.c | 42
> > ++++++++++++++++++++++++++++++++++
> > 1 file changed, 42 insertions(+)
> >
> >diff --git a/drivers/regulator/anatop-regulator.c
> >b/drivers/regulator/anatop-regulator.c
> >index 8f39cac..a857b9c 100644
> >--- a/drivers/regulator/anatop-regulator.c
> >+++ b/drivers/regulator/anatop-regulator.c
> >@@ -31,12 +31,18 @@
> > #include <linux/regulator/driver.h>
> > #include <linux/regulator/of_regulator.h>
> >+#define LDO_RAMP_UP_UNIT_IN_CYCLES 64 /* 64 cycles per step */
> >+#define LDO_RAMP_UP_FREQ_IN_MHZ 24 /* cycle based on 24M OSC */
> >+
> > struct anatop_regulator {
> > const char *name;
> > u32 control_reg;
> > struct regmap *anatop;
> > int vol_bit_shift;
> > int vol_bit_width;
> >+ u32 delay_reg;
> >+ int delay_bit_shift;
> >+ int delay_bit_width;
> > int min_bit_val;
> > int min_voltage;
> > int max_voltage;
> >@@ -55,6 +61,33 @@ static int anatop_regmap_set_voltage_sel(struct
> >regulator_dev *reg,
> > return regulator_set_voltage_sel_regmap(reg, selector);
> > }
> >+static int anatop_regmap_set_voltage_time_sel(struct regulator_dev *reg,
> >+ unsigned int old_sel,
> >+ unsigned int new_sel)
> >+{
> >+ struct anatop_regulator *anatop_reg = rdev_get_drvdata(reg);
> >+ u32 val;
> >+ int ret = 0;
> >+
> >+ /* check whether need to care about LDO ramp up speed */
> >+ if (anatop_reg->delay_reg) {
> >+ /*
> >+ * the delay for LDO ramp up time is
> >+ * based on the register setting, we need
> >+ * to calculate how many steps LDO need to
> >+ * ramp up, and how much delay needed. (us)
> >+ */
> >+ regmap_read(anatop_reg->anatop, anatop_reg->delay_reg, &val);
> >+ val = (val >> anatop_reg->delay_bit_shift) &
> >+ ((1 << anatop_reg->delay_bit_width) - 1);
> >+ ret = new_sel > old_sel ? (new_sel - old_sel) *
>
> The (new_sel > old_sel) could be part of the above if.
>
> if (anatop_reg->delay_reg && new_sel > old_sel)
[Anson Huang]Good point, accepted. Please help review my v3 patch,thanks!
>
> >+ ((LDO_RAMP_UP_UNIT_IN_CYCLES << val) /
> >+ LDO_RAMP_UP_FREQ_IN_MHZ + 1) : 0;
> >+ }
> >+
> >+ return ret;
> >+}
> >+
> > static int anatop_regmap_get_voltage_sel(struct regulator_dev *reg)
> > {
> > struct anatop_regulator *anatop_reg = rdev_get_drvdata(reg);
> >@@ -67,6 +100,7 @@ static int anatop_regmap_get_voltage_sel(struct
> >regulator_dev *reg)
> > static struct regulator_ops anatop_rops = {
> > .set_voltage_sel = anatop_regmap_set_voltage_sel,
> >+ .set_voltage_time_sel = anatop_regmap_set_voltage_time_sel,
> > .get_voltage_sel = anatop_regmap_get_voltage_sel,
> > .list_voltage = regulator_list_voltage_linear,
> > .map_voltage = regulator_map_voltage_linear,
> >@@ -143,6 +177,14 @@ static int anatop_regulator_probe(struct
> >platform_device *pdev)
> > goto anatop_probe_end;
> > }
> >+ /* read LDO ramp up setting, only for core reg */
> >+ of_property_read_u32(np, "anatop-delay-reg-offset",
> >+ &sreg->delay_reg);
> >+ of_property_read_u32(np, "anatop-delay-bit-width",
> >+ &sreg->delay_bit_width);
> >+ of_property_read_u32(np, "anatop-delay-bit-shift",
> >+ &sreg->delay_bit_shift);
> >+
> > rdesc->n_voltages = (sreg->max_voltage - sreg->min_voltage) / 25000 + 1
> > + sreg->min_bit_val;
> > rdesc->min_uV = sreg->min_voltage;
>
>
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
