Hi Tony, >> From: linux-arm-kernel [mailto:linux-arm-kernel- >> [email protected]] On Behalf Of Anil Kumar >> Sent: Wednesday, February 27, 2013 8:03 AM >> To: [email protected]; [email protected]; >> [email protected]; [email protected] >> Cc: [email protected]; Cousson, Benoit; Tony Lindgren; Grant >> Likely; Anil Kumar; [email protected] >> Subject: Re: FW: [PATCH V4] ARM: dts: add minimal DT support for >> DevKit8000. >> >> Hi, >> > >> > DevKit8000 is a beagle board clone from Timll, sold by >> > armkits.com. The DevKit8000 has RS232 serial port, LCD, DVI-D, >> > S-Video, Ethernet, SD/MMC, keyboard, camera, SPI, I2C, USB and >> > JTAG interface. >> > >> > This patch adds the basic DT support for devkit8000. At this time, >> Information >> > of twl4030 (PMIC), MMC1, I2C1 and leds are added. >> > >> > Signed-off-by: Anil Kumar <[email protected]> >> > Tested-by: Thomas Weber <[email protected]> >> >> Gentle Ping. As there are no review comments on this patch, >> Could you please pull this patch ?
Gentle Ping. This patch also got Reviewed-by: Manish Badarkhe <[email protected]> and as patch "ARM: dts: omap3-devkit8000: Enable audio support" has already got "Acked-by: Peter Ujfalusi <[email protected]>" but it is on the top of this patch. So, Could you please pull this patch in one of your omap branch? or you want me to do rebase this patch on top of v3.9-rc1 ? Thanks, Anil >> >> > --- >> > -This patch is based on top of kernel 3.8-rc5. >> > >> > -Tested on Devkit8000. >> > >> > For V4: >> > -Tiny nitpick. >> > >> > For V3: >> > - Remove pin mux as done at device boot time by default. >> > >> > For V2: >> > - Change model name as "TimLL OMAP3 Devkit8000" >> > - Change compatible as "timll,omap3-devkit8000" >> > - Doing i2c1 pinmux default with pinctrl-single driver instead of >> i2c1 >> > driver probe time. >> > >> > :100644 100644 5ebb44f... 22ebc76... M arch/arm/boot/dts/Makefile >> > :000000 100644 0000000... 2e1463a... A arch/arm/boot/dts/omap3- >> devkit8000.dts >> > :100644 100644 53cb380b.. ccecb76... M arch/arm/mach-omap2/board- >> generic.c >> > arch/arm/boot/dts/Makefile | 1 + >> > arch/arm/boot/dts/omap3-devkit8000.dts | 102 >> ++++++++++++++++++++++++++++++++ >> > arch/arm/mach-omap2/board-generic.c | 1 + >> > 3 files changed, 104 insertions(+), 0 deletions(-) >> > >> > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile >> > index 5ebb44f..22ebc76 100644 >> > --- a/arch/arm/boot/dts/Makefile >> > +++ b/arch/arm/boot/dts/Makefile >> > @@ -102,6 +102,7 @@ dtb-$(CONFIG_ARCH_MXS) += imx23-evk.dtb \ >> > imx28-tx28.dtb >> > dtb-$(CONFIG_ARCH_OMAP2PLUS) += omap2420-h4.dtb \ >> > omap3-beagle.dtb \ >> > + omap3-devkit8000.dtb \ >> > omap3-beagle-xm.dtb \ >> > omap3-evm.dtb \ >> > omap3-tobi.dtb \ >> > diff --git a/arch/arm/boot/dts/omap3-devkit8000.dts >> b/arch/arm/boot/dts/omap3-devkit8000.dts >> > new file mode 100644 >> > index 0000000..2e1463a >> > --- /dev/null >> > +++ b/arch/arm/boot/dts/omap3-devkit8000.dts >> > @@ -0,0 +1,102 @@ >> > +/* >> > + * Author: Anil Kumar <[email protected]> >> > + * >> > + * This program is free software; you can redistribute it and/or >> modify >> > + * it under the terms of the GNU General Public License version 2 as >> > + * published by the Free Software Foundation. >> > + */ >> > +/dts-v1/; >> > + >> > +/include/ "omap3.dtsi" >> > +/ { >> > + model = "TimLL OMAP3 Devkit8000"; >> > + compatible = "timll,omap3-devkit8000", "ti,omap3"; >> > + >> > + memory { >> > + device_type = "memory"; >> > + reg = <0x80000000 0x10000000>; /* 256 MB */ >> > + }; >> > + >> > + leds { >> > + compatible = "gpio-leds"; >> > + >> > + heartbeat { >> > + label = "devkit8000::led1"; >> > + gpios = <&gpio6 26 0>; /* 186 -> LED1 */ >> > + default-state = "on"; >> > + linux,default-trigger = "heartbeat"; >> > + }; >> > + >> > + mmc { >> > + label = "devkit8000::led2"; >> > + gpios = <&gpio6 3 0>; /* 163 -> LED2 */ >> > + default-state = "on"; >> > + linux,default-trigger = "none"; >> > + }; >> > + >> > + usr { >> > + label = "devkit8000::led3"; >> > + gpios = <&gpio6 4 0>; /* 164 -> LED3 */ >> > + default-state = "on"; >> > + linux,default-trigger = "usr"; >> > + }; >> > + }; >> > +}; >> > + >> > +&i2c1 { >> > + clock-frequency = <2600000>; >> > + >> > + twl: twl@48 { >> > + reg = <0x48>; >> > + interrupts = <7>; /* SYS_NIRQ cascaded to intc >> */ >> > + interrupt-parent = <&intc>; >> > + }; >> > +}; >> > + >> > +&i2c2 { >> > + status = "disabled"; >> > +}; >> > + >> > +&i2c3 { >> > + status = "disabled"; >> > +}; >> > + >> > +/include/ "twl4030.dtsi" >> > + >> > +&mmc1 { >> > + vmmc-supply = <&vmmc1>; >> > + vmmc_aux-supply = <&vsim>; >> > + bus-width = <8>; >> > +}; >> > + >> > +&mmc2 { >> > + status = "disabled"; >> > +}; >> > + >> > +&mmc3 { >> > + status = "disabled"; >> > +}; >> > + >> > +&wdt2 { >> > + status = "disabled"; >> > +}; >> > + >> > +&mcbsp1 { >> > + status = "disabled"; >> > +}; >> > + >> > +&mcbsp2 { >> > + status = "disabled"; >> > +}; >> > + >> > +&mcbsp3 { >> > + status = "disabled"; >> > +}; >> > + >> > +&mcbsp4 { >> > + status = "disabled"; >> > +}; >> > + >> > +&mcbsp5 { >> > + status = "disabled"; >> > +}; >> > diff --git a/arch/arm/mach-omap2/board-generic.c b/arch/arm/mach- >> omap2/board-generic.c >> > index 53cb380..ccecb76 100644 >> > --- a/arch/arm/mach-omap2/board-generic.c >> > +++ b/arch/arm/mach-omap2/board-generic.c >> > @@ -110,6 +110,7 @@ MACHINE_END >> > >> > static const char *omap3_gp_boards_compat[] __initdata = { >> > "ti,omap3-beagle", >> > + "timll,omap3-devkit8000", >> > NULL, >> > }; >> > >> > -- >> > 1.7.0.4 >> > >> > >> > _______________________________________________ >> > linux-arm-kernel mailing list >> > [email protected] >> > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel >> >> _______________________________________________ >> linux-arm-kernel mailing list >> [email protected] >> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel -- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
