On 10/15/2013 01:02 PM, George Cherian wrote:
> This adds omap control module support for USBSS in AM437x SoC.
> Update DT binding information to reflect these changes.
>
> Signed-off-by: George Cherian <george.cher...@ti.com>
Acked-by: Roger Quadros <rog...@ti.com>
> ---
> Changes from v1:
> Make ON and OFF operations symmetric.
>
> Documentation/devicetree/bindings/usb/omap-usb.txt | 2 ++
> drivers/usb/phy/phy-omap-control.c | 19 +++++++++++++++++++
> include/linux/usb/omap_control_usb.h | 6 ++++++
> 3 files changed, 27 insertions(+)
>
> diff --git a/Documentation/devicetree/bindings/usb/omap-usb.txt
> b/Documentation/devicetree/bindings/usb/omap-usb.txt
> index 090e5e2..c495135 100644
> --- a/Documentation/devicetree/bindings/usb/omap-usb.txt
> +++ b/Documentation/devicetree/bindings/usb/omap-usb.txt
> @@ -87,6 +87,8 @@ Required properties:
> e.g. USB3 PHY and SATA PHY on OMAP5.
> "ti,control-phy-dra7usb2" - if it has power down register like USB2 PHY on
> DRA7 platform.
> + "ti,control-phy-am437usb2" - if it has power down register like USB2 PHY on
> + AM437 platform.
> - reg : Address and length of the register set for the device. It contains
> the address of "otghs_control" for control-phy-otghs or "power" register
> for other types.
> diff --git a/drivers/usb/phy/phy-omap-control.c
> b/drivers/usb/phy/phy-omap-control.c
> index 09c5ace..e725318 100644
> --- a/drivers/usb/phy/phy-omap-control.c
> +++ b/drivers/usb/phy/phy-omap-control.c
> @@ -84,6 +84,20 @@ void omap_control_usb_phy_power(struct device *dev, int on)
> else
> val |= OMAP_CTRL_USB2_PHY_PD;
> break;
> +
> + case OMAP_CTRL_TYPE_AM437USB2:
> + if (on) {
> + val &= ~(AM437X_CTRL_USB2_PHY_PD |
> + AM437X_CTRL_USB2_OTG_PD);
> + val |= (AM437X_CTRL_USB2_OTGVDET_EN |
> + AM437X_CTRL_USB2_OTGSESSEND_EN);
> + } else {
> + val &= ~(AM437X_CTRL_USB2_OTGVDET_EN |
> + AM437X_CTRL_USB2_OTGSESSEND_EN);
> + val |= (AM437X_CTRL_USB2_PHY_PD |
> + AM437X_CTRL_USB2_OTG_PD);
> + }
> + break;
> default:
> dev_err(dev, "%s: type %d not recognized\n",
> __func__, control_usb->type);
> @@ -197,6 +211,7 @@ static const enum omap_control_usb_type otghs_data =
> OMAP_CTRL_TYPE_OTGHS;
> static const enum omap_control_usb_type usb2_data = OMAP_CTRL_TYPE_USB2;
> static const enum omap_control_usb_type pipe3_data = OMAP_CTRL_TYPE_PIPE3;
> static const enum omap_control_usb_type dra7usb2_data =
> OMAP_CTRL_TYPE_DRA7USB2;
> +static const enum omap_control_usb_type am437usb2_data =
> OMAP_CTRL_TYPE_AM437USB2;
>
> static const struct of_device_id omap_control_usb_id_table[] = {
> {
> @@ -215,6 +230,10 @@ static const struct of_device_id
> omap_control_usb_id_table[] = {
> .compatible = "ti,control-phy-dra7usb2",
> .data = &dra7usb2_data,
> },
> + {
> + .compatible = "ti,control-phy-am437usb2",
> + .data = &am437usb2_data,
> + },
> {},
> };
> MODULE_DEVICE_TABLE(of, omap_control_usb_id_table);
> diff --git a/include/linux/usb/omap_control_usb.h
> b/include/linux/usb/omap_control_usb.h
> index 596b019..69ae383 100644
> --- a/include/linux/usb/omap_control_usb.h
> +++ b/include/linux/usb/omap_control_usb.h
> @@ -24,6 +24,7 @@ enum omap_control_usb_type {
> OMAP_CTRL_TYPE_USB2, /* USB2_PHY, power down in CONTROL_DEV_CONF */
> OMAP_CTRL_TYPE_PIPE3, /* PIPE3 PHY, DPLL & seperate Rx/Tx power */
> OMAP_CTRL_TYPE_DRA7USB2, /* USB2 PHY, power and power_aux e.g. DRA7 */
> + OMAP_CTRL_TYPE_AM437USB2, /* USB2 PHY, power e.g. AM437x */
> };
>
> struct omap_control_usb {
> @@ -64,6 +65,11 @@ enum omap_control_usb_mode {
>
> #define OMAP_CTRL_USB2_PHY_PD BIT(28)
>
> +#define AM437X_CTRL_USB2_PHY_PD BIT(0)
> +#define AM437X_CTRL_USB2_OTG_PD BIT(1)
> +#define AM437X_CTRL_USB2_OTGVDET_EN BIT(19)
> +#define AM437X_CTRL_USB2_OTGSESSEND_EN BIT(20)
> +
> #if IS_ENABLED(CONFIG_OMAP_CONTROL_USB)
> extern void omap_control_usb_phy_power(struct device *dev, int on);
> extern void omap_control_usb_set_mode(struct device *dev,
>
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
