On Sat, Oct 26, 2013 at 01:47:40AM -0500, Kumar Gala wrote:
>
> On Oct 26, 2013, at 1:46 AM, Kumar Gala wrote:
>
> >
> > On Oct 25, 2013, at 7:00 PM, Wendy Ng wrote:
> >
> >> This adds the support for Temperature Monitor (TMON) driver for
> >> Broadcom bcm281xx SoCs. This driver plugs into the Thermal Framework.
> >>
> >> Note that this version of the TMON driver does support interrupt-driven
> >> mode -- only polling-mode of the thermal framework can be used.
> >>
> >> Signed-off-by: Wendy Ng <wendy...@broadcom.com>
> >> Reviewed-by: Markus Mayer <mma...@broadcom.com>
> >> Reviewed-by: Christian Daudt <c...@broadcom.com>
> >> Reviewed-by: Matt Porter <matt.por...@linaro.org>
> >> Reviewed-by: Tim Kryger <tim.kry...@linaro.org>
> >> ---
> >> .../bindings/thermal/bcm-kona-thermal.txt | 24 +++
> >> drivers/thermal/Kconfig | 11 ++
> >> drivers/thermal/Makefile | 1 +
> >> drivers/thermal/bcm_kona_tmon.c | 173
> >> ++++++++++++++++++++
> >> 4 files changed, 209 insertions(+)
> >> create mode 100644
> >> Documentation/devicetree/bindings/thermal/bcm-kona-thermal.txt
> >> create mode 100644 drivers/thermal/bcm_kona_tmon.c
> >>
> >> diff --git
> >> a/Documentation/devicetree/bindings/thermal/bcm-kona-thermal.txt
> >> b/Documentation/devicetree/bindings/thermal/bcm-kona-thermal.txt
> >> new file mode 100644
> >> index 0000000..225b898
> >> --- /dev/null
> >> +++ b/Documentation/devicetree/bindings/thermal/bcm-kona-thermal.txt
> >> @@ -0,0 +1,24 @@
> >> +* Broadcom Kona TMON bindings
> >> +
> >> +This version is for the Kona family of SoCs. The TMON (Temperature
> >> Monitor)
> >> +block in a Kona SoC device is used to measure the chip temperature at
> >> constant
> >> +intervals.
> >> +The TMON block asserts an interrupt if temperature exceeds a user
> >> programmed
> >> +threshold value. The TMON block would reset the entire device once it
> >> +reaches a critical temperature which is also a programmable setting.
> >> +
> >> +Required properties:
> >> +- compatible : "brcm,bcm11351-tmon", "brcm,kona-tmon"
> >> +- reg : Address range of the thermal register
> >> +- clocks : the clock signal that drives the TMON block
> >> +- interrupts: the interrupt signal associated with the TMON block
> >> +
> >> +
> >> +Example:
> >> + tmon@34008000 {
> >> + compatible = "brcm,bcm11351-tmon", "brcm,kona-tmon";
> >> + reg = <0x34008000 0x0024>;
> >> + clocks = <&tmon_1m_clk>;
> >> + interrupts = <GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>;
> >> + status = "disabled";
> >
> > I'd remove the 'status' line from an example.
> >
> >> + };
> >
> > Ack on the binding (beyond my minor nit pick on the status prop).
> >
> > Acked-by: Kumar Gala <ga...@codeaurora.org>
> >
> > - k
>
>
> After looking at your .dts{i} I see you've got a #thermal-sensor-cells prop,
> where is that documented?
It's in Eduardo's "device thermal limits represented in device tree
nodes" series. Here's the direct link to the binding post/discussion
https://lkml.org/lkml/2013/9/26/772
-Matt
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
