On Wed, Jan 19, 2005 at 04:18:49PM -0500, Richard Koch wrote:
> Please include the patch below to bring the ICS MK712 touchscreen controller
> support, which is in kernel 2.4, in to kernel 2.6.
>
> This patch was constructed and applied to kernel version 2.6.10 and tested
> successfully on several Gateway AOL Connected Touchpad computers.
>
> This was based on the mk712.c 2.4.28 version. No functional changes applied
> only minor
> changes to conform to the 2.6 build structure. I choose to place the driver
> under
> input/touchscreen as this seemed most appropriate.
>
> By making a contribution to this project, I certify that:
>
> The contribution is based upon previous work that, to the best
> of my knowledge, is covered under an appropriate open source
> license and I have the right under that license to submit that
> work with modifications, whether created in whole or in part
> by me, under the same open source license (unless I am
> permitted to submit under a different license), as indicated
> in the file.
>
> Signed-off-by: Rick Koch <[EMAIL PROTECTED]>
>
> patch also available at: http://home.comcast.net/~n1gp/mk712_2.6_patch
I converted it to a proper input driver for you. ;) Can you check it if
it still works?
[EMAIL PROTECTED], 2005-02-05 22:00:45+01:00, [EMAIL PROTECTED]
input: New driver for ICS MicroClock MK712 TouchScreens.
Signed-off-by: Vojtech Pavlik <[EMAIL PROTECTED]>
Kconfig | 11 +++
Makefile | 3
mk712.c | 201 +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
3 files changed, 214 insertions(+), 1 deletion(-)
diff -Nru a/drivers/input/touchscreen/Kconfig
b/drivers/input/touchscreen/Kconfig
--- a/drivers/input/touchscreen/Kconfig 2005-02-05 22:01:13 +01:00
+++ b/drivers/input/touchscreen/Kconfig 2005-02-05 22:01:13 +01:00
@@ -48,4 +48,15 @@
To compile this driver as a module, choose M here: the
module will be called gunze.
+config TOUCHSCREEN_MK712
+ tristate "ICS MicroClock MK712 touchscreen"
+ help
+ Say Y here if you have the ICS MicroClock MK712 touchscreen
+ controller chip in your system.
+
+ If unsure, say N.
+
+ To compile this driver as a module, choose M here: the
+ module will be called mk712.
+
endif
diff -Nru a/drivers/input/touchscreen/Makefile
b/drivers/input/touchscreen/Makefile
--- a/drivers/input/touchscreen/Makefile 2005-02-05 22:01:13 +01:00
+++ b/drivers/input/touchscreen/Makefile 2005-02-05 22:01:13 +01:00
@@ -5,5 +5,6 @@
# Each configuration option enables a list of files.
obj-$(CONFIG_TOUCHSCREEN_BITSY) += h3600_ts_input.o
-obj-$(CONFIG_TOUCHSCREEN_GUNZE) += gunze.o
obj-$(CONFIG_TOUCHSCREEN_CORGI) += corgi_ts.o
+obj-$(CONFIG_TOUCHSCREEN_GUNZE) += gunze.o
+obj-$(CONFIG_TOUCHSCREEN_MK712) += mk712.o
diff -Nru a/drivers/input/touchscreen/mk712.c
b/drivers/input/touchscreen/mk712.c
--- /dev/null Wed Dec 31 16:00:00 196900
+++ b/drivers/input/touchscreen/mk712.c 2005-02-05 22:01:13 +01:00
@@ -0,0 +1,201 @@
+/*
+ * ICS MK712 touchscreen controller driver
+ *
+ * Copyright (c) 1999-2002 Transmeta Corporation
+ * Copyright (c) 2005 Rick Koch <[EMAIL PROTECTED]>
+ * Copyright (c) 2005 Vojtech Pavlik <[EMAIL PROTECTED]>
+ */
+
+/*
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ */
+
+/*
+ * This driver supports the ICS MicroClock MK712 TouchScreen controller,
+ * found in Gateway AOL Connected Touchpad computers.
+ *
+ * Documentation for ICS MK712 can be found at:
+ * http://www.icst.com/pdf/mk712.pdf
+ */
+
+/*
+ * 1999-12-18: original version, Daniel Quinlan
+ * 1999-12-19: added anti-jitter code, report pen-up events, fixed mk712_poll
+ * to use queue_empty, Nathan Laredo
+ * 1999-12-20: improved random point rejection, Nathan Laredo
+ * 2000-01-05: checked in new anti-jitter code, changed mouse protocol, fixed
+ * queue code, added module options, other fixes, Daniel Quinlan
+ * 2002-03-15: Clean up for kernel merge <[EMAIL PROTECTED]>
+ * Fixed multi open race, fixed memory checks, fixed resource
+ * allocation, fixed close/powerdown bug, switched to new init
+ * 2005-01-18: Ported to 2.6 from 2.4.28, Rick Koch
+ * 2005-02-05: Rewritten for the input layer, Vojtech Pavlik
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/moduleparam.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/errno.h>
+#include <linux/delay.h>
+#include <linux/ioport.h>
+#include <linux/interrupt.h>
+#include <linux/input.h>
+#include <asm/io.h>
+
+MODULE_AUTHOR("Daniel Quinlan <[EMAIL PROTECTED]>, Vojtech Pavlik <[EMAIL
PROTECTED]>");
+MODULE_DESCRIPTION("ICS MicroClock MK712 TouchScreen driver");
+MODULE_LICENSE("GPL");
+
+static unsigned int mk712_io = 0x260; /* Also 0x200, 0x208, 0x300 */
+module_param_named(io, mk712_io, uint, 0);
+MODULE_PARM_DESC(io, "I/O base address of MK712 touchscreen controller");
+
+static unsigned int mk712_irq = 10; /* Also 12, 14, 15 */
+module_param_named(irq, mk712_irq, uint, 0);
+MODULE_PARM_DESC(irq, "IRQ of MK712 touchscreen controller");
+
+/* eight 8-bit registers */
+#define MK712_STATUS 0
+#define MK712_X 2
+#define MK712_Y 4
+#define MK712_CONTROL 6
+#define MK712_RATE 7
+
+/* status */
+#define MK712_STATUS_TOUCH 0x10
+#define MK712_CONVERSION_COMPLETE 0x80
+
+/* control */
+#define MK712_ENABLE_INT 0x01
+#define MK712_INT_ON_CONVERSION_COMPLETE 0x02
+#define MK712_INT_ON_CHANGE_IN_TOUCH_STATUS 0x04
+#define MK712_ENABLE_PERIODIC_CONVERSIONS 0x10
+#define MK712_READ_ONE_POINT 0x20
+#define MK712_POWERDOWN 0x40
+
+static int mk712_used = 0;
+static struct input_dev mk712_dev;
+
+static irqreturn_t mk712_interrupt(int irq, void *dev_id, struct pt_regs *regs)
+{
+ unsigned char status;
+ static int debounce = 1;
+ static unsigned short last_x;
+ static unsigned short last_y;
+
+ input_regs(&mk712_dev, regs);
+
+ status = inb(mk712_io + MK712_STATUS);
+
+ if (~status & MK712_CONVERSION_COMPLETE) {
+ debounce = 1;
+ goto end;
+ }
+
+ if (~status & MK712_STATUS_TOUCH)
+ {
+ debounce = 1;
+ input_report_key(&mk712_dev, BTN_TOUCH, 0);
+ goto end;
+ }
+
+ if (debounce)
+ {
+ debounce = 0;
+ goto end;
+ }
+
+ input_report_key(&mk712_dev, BTN_TOUCH, 1);
+ input_report_abs(&mk712_dev, ABS_X, last_x);
+ input_report_abs(&mk712_dev, ABS_Y, last_y);
+
+end:
+
+ last_x = inw(mk712_io + MK712_X) & 0x0fff;
+ last_y = (inw(mk712_io + MK712_Y) & 0x0fff) * 3 / 4;
+ input_sync(&mk712_dev);
+ return IRQ_HANDLED;
+}
+
+static int mk712_open(struct input_dev *dev)
+{
+
+ if (mk712_used++)
+ return 0;
+
+ outb(0, mk712_io + MK712_CONTROL); /* Reset */
+
+ outb(MK712_ENABLE_INT | MK712_INT_ON_CONVERSION_COMPLETE |
+ MK712_INT_ON_CHANGE_IN_TOUCH_STATUS |
+ MK712_ENABLE_PERIODIC_CONVERSIONS |
+ MK712_POWERDOWN, mk712_io + MK712_CONTROL);
+
+ outb(10, mk712_io + MK712_RATE); /* 187 points per second */
+
+ return 0;
+}
+
+static void mk712_close(struct input_dev *dev)
+{
+ if (--mk712_used)
+ return;
+
+ outb(0, mk712_io + MK712_CONTROL);
+}
+
+static struct input_dev mk712_dev = {
+ .evbit = { BIT(EV_KEY) | BIT(EV_ABS) },
+ .keybit = { [LONG(BTN_LEFT)] = BIT(BTN_TOUCH) },
+ .absbit = { BIT(ABS_X) | BIT(ABS_Y) },
+ .open = mk712_open,
+ .close = mk712_close,
+ .name = "ICS MicroClock MK712 TouchScreen",
+ .phys = "isa0260/input0",
+ .absmin = { [ABS_X] = 0, [ABS_Y] = 0 },
+ .absmax = { [ABS_X] = 0xfff, [ABS_Y] = 0xbff },
+ .absfuzz = { [ABS_X] = 88, [ABS_Y] = 88 },
+ .id = {
+ .bustype = BUS_ISA,
+ .vendor = 0x0005,
+ .product = 0x0001,
+ .version = 0x0100,
+ },
+};
+
+int __init mk712_init(void)
+{
+
+ if(!request_region(mk712_io, 8, "mk712"))
+ {
+ printk(KERN_WARNING "mk712: unable to get IO region\n");
+ return -ENODEV;
+ }
+
+ if(request_irq(mk712_irq, mk712_interrupt, 0, "mk712", &mk712_dev))
+ {
+ printk(KERN_WARNING "mk712: unable to get IRQ\n");
+ release_region(mk712_io, 8);
+ return -EBUSY;
+ }
+
+ input_register_device(&mk712_dev);
+
+ printk(KERN_INFO "input: ICS MicroClock MK712 TouchScreen at %#x irq
%d\n", mk712_io, mk712_irq);
+
+ return 0;
+}
+
+static void __exit mk712_exit(void)
+{
+ input_unregister_device(&mk712_dev);
+ free_irq(mk712_irq, &mk712_dev);
+ release_region(mk712_io, 8);
+}
+
+
+module_init(mk712_init);
+module_exit(mk712_exit);
--
Vojtech Pavlik
SuSE Labs, SuSE CR
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [EMAIL PROTECTED]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
