Use the clock framework to en/disable the clock to the au1100 framebuffer device.
Signed-off-by: Manuel Lauss <[email protected]> --- arch/mips/alchemy/devboards/db1000.c | 14 ++++++++++++++ drivers/video/fbdev/au1100fb.c | 36 ++++++++++++++++++++++-------------- drivers/video/fbdev/au1100fb.h | 1 + 3 files changed, 37 insertions(+), 14 deletions(-) diff --git a/arch/mips/alchemy/devboards/db1000.c b/arch/mips/alchemy/devboards/db1000.c index 6e55bcc..5b4f81b 100644 --- a/arch/mips/alchemy/devboards/db1000.c +++ b/arch/mips/alchemy/devboards/db1000.c @@ -19,6 +19,7 @@ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA */ +#include <linux/clk.h> #include <linux/dma-mapping.h> #include <linux/gpio.h> #include <linux/init.h> @@ -496,6 +497,7 @@ int __init db1000_dev_setup(void) int board = BCSR_WHOAMI_BOARD(bcsr_read(BCSR_WHOAMI)); int c0, c1, d0, d1, s0, s1, flashsize = 32, twosocks = 1; unsigned long pfc; + struct clk *c, *p; if (board == BCSR_WHOAMI_DB1500) { c0 = AU1500_GPIO2_INT; @@ -525,6 +527,18 @@ int __init db1000_dev_setup(void) spi_register_board_info(db1100_spi_info, ARRAY_SIZE(db1100_spi_info)); + /* link LCD clock to AUXPLL */ + p = clk_get(NULL, "auxpll_clk"); + c = clk_get(NULL, "lcd_intclk"); + if (!IS_ERR(c) && !IS_ERR(p)) { + clk_set_parent(c, p); + clk_set_rate(c, clk_get_rate(p)); + } + if (!IS_ERR(c)) + clk_put(c); + if (!IS_ERR(p)) + clk_put(p); + platform_add_devices(db1100_devs, ARRAY_SIZE(db1100_devs)); platform_device_register(&db1100_spi_dev); } else if (board == BCSR_WHOAMI_DB1000) { diff --git a/drivers/video/fbdev/au1100fb.c b/drivers/video/fbdev/au1100fb.c index 2c2804b..a7145ce 100644 --- a/drivers/video/fbdev/au1100fb.c +++ b/drivers/video/fbdev/au1100fb.c @@ -41,6 +41,7 @@ * with this program; if not, write to the Free Software Foundation, Inc., * 675 Mass Ave, Cambridge, MA 02139, USA. */ +#include <linux/clk.h> #include <linux/module.h> #include <linux/kernel.h> #include <linux/errno.h> @@ -434,7 +435,7 @@ static int au1100fb_drv_probe(struct platform_device *dev) struct au1100fb_device *fbdev = NULL; struct resource *regs_res; unsigned long page; - u32 sys_clksrc; + struct clk *c; /* Allocate new device private */ fbdev = devm_kzalloc(&dev->dev, sizeof(struct au1100fb_device), @@ -473,6 +474,13 @@ static int au1100fb_drv_probe(struct platform_device *dev) print_dbg("Register memory map at %p", fbdev->regs); print_dbg("phys=0x%08x, size=%d", fbdev->regs_phys, fbdev->regs_len); + c = clk_get(NULL, "lcd_intclk"); + if (!IS_ERR(c)) { + fbdev->lcdclk = c; + clk_set_rate(c, 48000000); + clk_prepare_enable(c); + } + /* Allocate the framebuffer to the maximum screen size * nbr of video buffers */ fbdev->fb_len = fbdev->panel->xres * fbdev->panel->yres * (fbdev->panel->bpp >> 3) * AU1100FB_NBR_VIDEO_BUFFERS; @@ -506,11 +514,6 @@ static int au1100fb_drv_probe(struct platform_device *dev) print_dbg("Framebuffer memory map at %p", fbdev->fb_mem); print_dbg("phys=0x%08x, size=%dK", fbdev->fb_phys, fbdev->fb_len / 1024); - /* Setup LCD clock to AUX (48 MHz) */ - sys_clksrc = AU1X_RDSYS(AU1000_SYS_CLKSRC) & - ~(SYS_CS_ML_MASK | SYS_CS_DL | SYS_CS_CL); - AU1X_WRSYS((sys_clksrc | (1 << SYS_CS_ML_BIT)), AU1000_SYS_CLKSRC); - /* load the panel info into the var struct */ au1100fb_var.bits_per_pixel = fbdev->panel->bpp; au1100fb_var.xres = fbdev->panel->xres; @@ -547,6 +550,10 @@ static int au1100fb_drv_probe(struct platform_device *dev) return 0; failed: + if (fbdev->lcdclk) { + clk_disable_unprepare(fbdev->lcdclk); + clk_put(fbdev->lcdclk); + } if (fbdev->fb_mem) { dma_free_noncoherent(&dev->dev, fbdev->fb_len, fbdev->fb_mem, fbdev->fb_phys); @@ -577,11 +584,15 @@ int au1100fb_drv_remove(struct platform_device *dev) fb_dealloc_cmap(&fbdev->info.cmap); + if (fbdev->lcdclk) { + clk_disable_unprepare(fbdev->lcdclk); + clk_put(fbdev->lcdclk); + } + return 0; } #ifdef CONFIG_PM -static u32 sys_clksrc; static struct au1100fb_regs fbregs; int au1100fb_drv_suspend(struct platform_device *dev, pm_message_t state) @@ -591,14 +602,11 @@ int au1100fb_drv_suspend(struct platform_device *dev, pm_message_t state) if (!fbdev) return 0; - /* Save the clock source state */ - sys_clksrc = AU1X_RDSYS(AU1000_SYS_CLKSRC); - /* Blank the LCD */ au1100fb_fb_blank(VESA_POWERDOWN, &fbdev->info); - /* Stop LCD clocking */ - AU1X_WRSYS(sys_clksrc & ~SYS_CS_ML_MASK, AU1000_SYS_CLKSRC); + if (fbdev->lcdclk) + clk_disable(fbdev->lcdclk); memcpy(&fbregs, fbdev->regs, sizeof(struct au1100fb_regs)); @@ -614,8 +622,8 @@ int au1100fb_drv_resume(struct platform_device *dev) memcpy(fbdev->regs, &fbregs, sizeof(struct au1100fb_regs)); - /* Restart LCD clocking */ - AU1X_WRSYS(sys_clksrc, AU1000_SYS_CLKSRC); + if (fbdev->lcdclk) + clk_enable(fbdev->lcdclk); /* Unblank the LCD */ au1100fb_fb_blank(VESA_NO_BLANKING, &fbdev->info); diff --git a/drivers/video/fbdev/au1100fb.h b/drivers/video/fbdev/au1100fb.h index 12d9642..9af1993 100644 --- a/drivers/video/fbdev/au1100fb.h +++ b/drivers/video/fbdev/au1100fb.h @@ -109,6 +109,7 @@ struct au1100fb_device { size_t fb_len; dma_addr_t fb_phys; int panel_idx; + struct clk *lcdclk; }; /********************************************************************/ -- 2.0.0 -- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
