Hi,
Am 20.08.2014 19:11, schrieb [email protected]:
> From: Pratik Patel <[email protected]>
>
> Coresight IP blocks allow for the support of HW assisted tracing
> on ARM SoCs. Bindings for the currently available blocks are
> presented herein.
>
> Signed-off-by: Pratik Patel <[email protected]>
> Signed-off-by: Panchaxari Prasannamurthy
> <[email protected]>
> Signed-off-by: Mathieu Poirier <[email protected]>
> ---
> .../devicetree/bindings/arm/coresight.txt | 205
> +++++++++++++++++++++
> 1 file changed, 205 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/arm/coresight.txt
>
> diff --git a/Documentation/devicetree/bindings/arm/coresight.txt
> b/Documentation/devicetree/bindings/arm/coresight.txt
> new file mode 100644
> index 0000000..2ee594d
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/arm/coresight.txt
> @@ -0,0 +1,205 @@
> +* CoreSight Components
> +
> +CoreSight components are compliant with the ARM CoreSight architecture
> +specification and can be connected in various topologies to suit a particular
> +SoCs tracing needs. These trace components can generally be classified as
> sinks,
> +links and sources. Trace data produced by one or more sources flows through
> the
> +intermediate links connecting the source to the currently selected sink. Each
> +CoreSight component device should use these properties to describe its
> hardware
> +characteristcs.
> +
> +Required properties for all components *except* non-configurable replicators:
> +
> +- compatible : name of the component used for driver matching. Possible
> values
> +include: "arm,coresight-etb10", "arm,coresight-tpiu", "arm,coresight-tmc",
> +"arm,coresight-funnel", and "arm,coresight-etm3x". All of these have to
> +be supplemented with "arm,primecell" as drivers are using the AMBA bus
> +interface. Since non-configurable replicators don't show up on the AMBA
> +bus they don't need to be post-fixed with "arm,primecell".
I think this document would be much easier to read if you indented these
paragraphs below "name" here. That way the actual property names would
stand out more when looking up a particular property.
> +
> +- reg : physical base address and length of the register set(s) of the
> component.
> +
> +- clocks : the clock associated to this component.
> +
> +- clock-names: the name of the clock as referenced by the code. Since we are
> +using the AMBA framework, the name should be "apb_pclk".
> +
> +- ports or port: The representation of the component's port layout using the
> +generic DT graph presentation found in "bindings/graph.txt".
> +
> +Non-configurable replicators:
> +
> +- compatible: currently supported value is "arm-replicator". Since
> non-configurable
> +replicators don't show up on the AMBA hey don't need to be post-fixed with
> +"arm,primecell".
> +
> +- id: a unique number that will identify this replicator.
> +
> +- ports or port: same as above.
> +
> +Optional properties for Sinks:
> +
> +- coresight-default-sink: must be specified for one of the sink devices that
> is
> +intended to be made the default sink. Other sink devices must not have this
> +specified. Not specifying this property on any of the sinks is invalid.
> +
> +Optional properties for ETM/PTMs:
> +
> +- arm,cp14: must be present if the system accesses ETM/PTM management
> registers
> +via co-processor 14.
> +
> +- arm,cp14: access to ETM/PTM management registers is made via cp14.
> +
> +- cpu: the cpu phandle this ETM/PTM is affined to. When omitted the source is
> +considered to belong to CPU0.
> +
> +Optional property for TMC:
> +
> +- arm,buffer-size: size of contiguous buffer space for TMC ETR (embedded
> trace router)
> +
> +
> +Example:
> +
> +1. Sinks
> + etb: etb@20010000 {
> + compatible = "arm,coresight-etb10", "arm,primecell";
> + reg = <0 0x20010000 0 0x1000>;
You seem to be using two address cells (and two size cells). In that
case, I believe I read it were convention to use etb@0,20010000?
Regards,
Andreas
> +
> + coresight-default-sink;
> + clocks = <&oscclk6a>;
> + clock-names = "apb_pclk";
> + port {
> + etb_in_port: endpoint@0 {
> + slave-mode;
> + remote-endpoint = <&replicator_out_port0>;
> + };
> + };
> + };
[snip]
--
SUSE LINUX Products GmbH, Maxfeldstr. 5, 90409 Nürnberg, Germany
GF: Jeff Hawn, Jennifer Guild, Felix Imendörffer; HRB 16746 AG Nürnberg
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
