From: huang lin <[email protected]> This adds basic SPI nodes to the base rk3288 device tree file.
A few notes: * It's assumed that most users of the SPI ports are using chip select 0. Thus the default pinctrl for the ports enables chip select 0 (but not chip select 1 on ports that have it). If a board wants to use chip select 1 or wants a GPIO chip select the board should override the pinctrl (just like boards can override UART pinctrl if they have hardware flow control). * Since SPI DMA support appears broken and the SPI works fine without DMA we don't include the DMA references. That can come in a later change. Signed-off-by: huang lin <[email protected]> Signed-off-by: Doug Anderson <[email protected]> --- arch/arm/boot/dts/rk3288.dtsi | 92 +++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 92 insertions(+) diff --git a/arch/arm/boot/dts/rk3288.dtsi b/arch/arm/boot/dts/rk3288.dtsi index 5f866e0..75d1f4c 100644 --- a/arch/arm/boot/dts/rk3288.dtsi +++ b/arch/arm/boot/dts/rk3288.dtsi @@ -34,6 +34,9 @@ serial2 = &uart2; serial3 = &uart3; serial4 = &uart4; + spi0 = &spi0; + spi1 = &spi1; + spi2 = &spi2; }; cpus { @@ -128,6 +131,45 @@ status = "disabled"; }; + spi0: spi@ff110000 { + compatible = "rockchip,rk3066-spi"; + clocks = <&cru SCLK_SPI0>, <&cru PCLK_SPI0>; + clock-names = "spiclk", "apb_pclk"; + interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&spi0_clk &spi0_tx &spi0_rx &spi0_cs0>; + reg = <0xff110000 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + spi1: spi@ff120000 { + compatible = "rockchip,rk3066-spi"; + clocks = <&cru SCLK_SPI1>, <&cru PCLK_SPI1>; + clock-names = "spiclk", "apb_pclk"; + interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&spi1_clk &spi1_tx &spi1_rx &spi1_cs0>; + reg = <0xff120000 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + spi2: spi@ff130000 { + compatible = "rockchip,rk3066-spi"; + clocks = <&cru SCLK_SPI2>, <&cru PCLK_SPI2>; + clock-names = "spiclk", "apb_pclk"; + interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&spi2_clk &spi2_tx &spi2_rx &spi2_cs0>; + reg = <0xff130000 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + i2c1: i2c@ff140000 { compatible = "rockchip,rk3288-i2c"; reg = <0xff140000 0x1000>; @@ -700,6 +742,56 @@ }; }; + spi0 { + spi0_clk: spi0-clk { + rockchip,pins = <5 12 RK_FUNC_1 &pcfg_pull_up>; + }; + spi0_cs0: spi0-cs0 { + rockchip,pins = <5 13 RK_FUNC_1 &pcfg_pull_up>; + }; + spi0_tx: spi0-tx { + rockchip,pins = <5 14 RK_FUNC_1 &pcfg_pull_up>; + }; + spi0_rx: spi0-rx { + rockchip,pins = <5 15 RK_FUNC_1 &pcfg_pull_up>; + }; + spi0_cs1: spi0-cs1 { + rockchip,pins = <5 16 RK_FUNC_1 &pcfg_pull_up>; + }; + }; + spi1 { + spi1_clk: spi1-clk { + rockchip,pins = <7 12 RK_FUNC_2 &pcfg_pull_up>; + }; + spi1_cs0: spi1-cs0 { + rockchip,pins = <7 13 RK_FUNC_2 &pcfg_pull_up>; + }; + spi1_rx: spi1-rx { + rockchip,pins = <7 14 RK_FUNC_2 &pcfg_pull_up>; + }; + spi1_tx: spi1-tx { + rockchip,pins = <7 15 RK_FUNC_2 &pcfg_pull_up>; + }; + }; + + spi2 { + spi2_cs1: spi2-cs1 { + rockchip,pins = <8 3 RK_FUNC_1 &pcfg_pull_up>; + }; + spi2_clk: spi2-clk { + rockchip,pins = <8 6 RK_FUNC_1 &pcfg_pull_up>; + }; + spi2_cs0: spi2-cs0 { + rockchip,pins = <8 7 RK_FUNC_1 &pcfg_pull_up>; + }; + spi2_rx: spi2-rx { + rockchip,pins = <8 8 RK_FUNC_1 &pcfg_pull_up>; + }; + spi2_tx: spi2-tx { + rockchip,pins = <8 9 RK_FUNC_1 &pcfg_pull_up>; + }; + }; + uart0 { uart0_xfer: uart0-xfer { rockchip,pins = <4 16 RK_FUNC_1 &pcfg_pull_up>, -- 2.1.0.rc2.206.gedb03e5 -- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
