Hi Krzysztof, I think that the state of some regulators should be changed in suspend state.
On 10/21/2014 05:25 PM, Krzysztof Kozlowski wrote:
> Add suspend to RAM configuration for max77686 regulators. Some LDOs and
> bucks are disabled. This reduces energy consumption during S2R,
> approximately from 17 mA to 9 mA.
>
> Additionally remove old and not supported bindings:
> - regulator-mem-off
> - regulator-mem-idle
> - regulator-mem-on
> The max77686 driver does not parse them and they are not documented
> anywere.
>
> Signed-off-by: Krzysztof Kozlowski <k.kozlow...@samsung.com>
> ---
> arch/arm/boot/dts/exynos4412-trats2.dts | 135
> +++++++++++++++++++++++++-------
> 1 file changed, 105 insertions(+), 30 deletions(-)
>
> diff --git a/arch/arm/boot/dts/exynos4412-trats2.dts
> b/arch/arm/boot/dts/exynos4412-trats2.dts
> index dd9ac66770f7..c2fbee36021a 100644
> --- a/arch/arm/boot/dts/exynos4412-trats2.dts
> +++ b/arch/arm/boot/dts/exynos4412-trats2.dts
> @@ -225,7 +225,9 @@
> regulator-min-microvolt = <1000000>;
> regulator-max-microvolt = <1000000>;
> regulator-always-on;
> - regulator-mem-on;
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + };
> };
>
> ldo2_reg: ldo2 {
> @@ -234,7 +236,9 @@
> regulator-min-microvolt = <1200000>;
> regulator-max-microvolt = <1200000>;
> regulator-always-on;
> - regulator-mem-on;
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + };
> };
>
> ldo3_reg: ldo3 {
> @@ -243,7 +247,9 @@
> regulator-min-microvolt = <1800000>;
> regulator-max-microvolt = <1800000>;
> regulator-always-on;
> - regulator-mem-on;
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + };
> };
>
> ldo4_reg: ldo4 {
> @@ -252,7 +258,9 @@
> regulator-min-microvolt = <2800000>;
> regulator-max-microvolt = <2800000>;
> regulator-always-on;
> - regulator-mem-on;
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + };
> };
>
> ldo5_reg: ldo5 {
> @@ -261,7 +269,9 @@
> regulator-min-microvolt = <1800000>;
> regulator-max-microvolt = <1800000>;
> regulator-always-on;
> - regulator-mem-on;
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + };
> };
>
> ldo6_reg: ldo6 {
> @@ -270,7 +280,9 @@
> regulator-min-microvolt = <1000000>;
> regulator-max-microvolt = <1000000>;
> regulator-always-on;
> - regulator-mem-on;
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + };
> };
>
> ldo7_reg: ldo7 {
> @@ -279,7 +291,9 @@
> regulator-min-microvolt = <1000000>;
> regulator-max-microvolt = <1000000>;
> regulator-always-on;
> - regulator-mem-on;
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + };
> };
>
> ldo8_reg: ldo8 {
> @@ -287,7 +301,9 @@
> regulator-name = "VMIPI_1.0V";
> regulator-min-microvolt = <1000000>;
> regulator-max-microvolt = <1000000>;
> - regulator-mem-off;
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> };
>
> ldo9_reg: ldo9 {
> @@ -295,7 +311,9 @@
> regulator-name = "CAM_ISP_MIPI_1.2V";
> regulator-min-microvolt = <1200000>;
> regulator-max-microvolt = <1200000>;
> - regulator-mem-idle;
> + regulator-state-mem {
> + regulator-on-in-suspend;
CAM_ISP_MIPI_1.2V is used for camera, I think this regulator should turn off in
suspend state
because camear could not be used in suspend state.
> + };
> };
>
> ldo10_reg: ldo10 {
> @@ -303,7 +321,9 @@
> regulator-name = "VMIPI_1.8V";
> regulator-min-microvolt = <1800000>;
> regulator-max-microvolt = <1800000>;
> - regulator-mem-off;
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> };
>
> ldo11_reg: ldo11 {
> @@ -312,7 +332,9 @@
> regulator-min-microvolt = <1950000>;
> regulator-max-microvolt = <1950000>;
> regulator-always-on;
> - regulator-mem-off;
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> };
>
> ldo12_reg: ldo12 {
> @@ -320,7 +342,9 @@
> regulator-name = "VUOTG_3.0V";
> regulator-min-microvolt = <3000000>;
> regulator-max-microvolt = <3000000>;
> - regulator-mem-off;
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> };
>
> ldo13_reg: ldo13 {
> @@ -328,7 +352,9 @@
> regulator-name = "NFC_AVDD_1.8V";
> regulator-min-microvolt = <1800000>;
> regulator-max-microvolt = <1800000>;
> - regulator-mem-idle;
> + regulator-state-mem {
> + regulator-on-in-suspend;
NFC_AVDD_1.8V is used for NFC feature, If user of smartphone want to use NFC
feature
and then enable NFC on the setting menu, NFC_AVDD_1.8V should turn on in
suspend state.
But, If NFC is not used, NFC_AVDD_1.8V should turn off in suspend state.
So, I think this regulator should be controlled by NFC device driver without
'regulator-state-mem' property.
> + };
> };
>
> ldo14_reg: ldo14 {
> @@ -337,7 +363,9 @@
> regulator-min-microvolt = <1950000>;
> regulator-max-microvolt = <1950000>;
> regulator-always-on;
> - regulator-mem-off;
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> };
>
> ldo15_reg: ldo15 {
> @@ -345,7 +373,9 @@
> regulator-name = "VHSIC_1.0V";
> regulator-min-microvolt = <1000000>;
> regulator-max-microvolt = <1000000>;
> - regulator-mem-off;
> + regulator-state-mem {
> + regulator-off-in-suspend;
VHSIC_1.8V was used for CP (Modem), CP (Modem) have to maintain the power in
suspend state.
- off -> on
> + };
> };
>
> ldo16_reg: ldo16 {
> @@ -353,7 +383,9 @@
> regulator-name = "VHSIC_1.8V";
> regulator-min-microvolt = <1800000>;
> regulator-max-microvolt = <1800000>;
> - regulator-mem-off;
> + regulator-state-mem {
> + regulator-off-in-suspend;
ditto (off -> on) for CP (MODEM)
> + };
> };
>
> ldo17_reg: ldo17 {
> @@ -361,7 +393,9 @@
> regulator-name = "CAM_SENSOR_CORE_1.2V";
> regulator-min-microvolt = <1200000>;
> regulator-max-microvolt = <1200000>;
> - regulator-mem-idle;
> + regulator-state-mem {
> + regulator-on-in-suspend;
ditto. (on -> off) because camera is not used in supend state.
> + };
> };
>
> ldo18_reg: ldo18 {
> @@ -369,7 +403,9 @@
> regulator-name = "CAM_ISP_SEN_IO_1.8V";
> regulator-min-microvolt = <1800000>;
> regulator-max-microvolt = <1800000>;
> - regulator-mem-idle;
> + regulator-state-mem {
> + regulator-on-in-suspend;
ditto. (on -> off) because camera is not used in supend state.
> + };
> };
>
> ldo19_reg: ldo19 {
> @@ -377,7 +413,9 @@
> regulator-name = "VT_CAM_1.8V";
> regulator-min-microvolt = <1800000>;
> regulator-max-microvolt = <1800000>;
> - regulator-mem-idle;
> + regulator-state-mem {
> + regulator-on-in-suspend;
ditto. (on -> off) because camera is not used in supend state.
> + };
> };
>
> ldo20_reg: ldo20 {
> @@ -385,7 +423,9 @@
> regulator-name = "VDDQ_PRE_1.8V";
> regulator-min-microvolt = <1800000>;
> regulator-max-microvolt = <1800000>;
> - regulator-mem-idle;
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + };
> };
>
> ldo21_reg: ldo21 {
> @@ -393,7 +433,9 @@
> regulator-name = "VTF_2.8V";
> regulator-min-microvolt = <2800000>;
> regulator-max-microvolt = <2800000>;
> - regulator-mem-idle;
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + };
> };
>
> ldo22_reg: ldo22 {
> @@ -401,6 +443,9 @@
> regulator-name = "VMEM_VDD_2.8V";
> regulator-min-microvolt = <2800000>;
> regulator-max-microvolt = <2800000>;
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + };
> };
>
> ldo23_reg: ldo23 {
> @@ -408,7 +453,9 @@
> regulator-name = "TSP_AVDD_3.3V";
> regulator-min-microvolt = <3300000>;
> regulator-max-microvolt = <3300000>;
> - regulator-mem-idle;
> + regulator-state-mem {
> + regulator-on-in-suspend;
ditto. (on -> off) because touchscreen is not used in suspend state.
> + };
> };
>
> ldo24_reg: ldo24 {
> @@ -416,7 +463,9 @@
> regulator-name = "TSP_VDD_1.8V";
> regulator-min-microvolt = <1800000>;
> regulator-max-microvolt = <1800000>;
> - regulator-mem-idle;
> + regulator-state-mem {
> + regulator-on-in-suspend;
ditto. (on -> off)
> + };
> };
>
> ldo25_reg: ldo25 {
> @@ -424,7 +473,9 @@
> regulator-name = "LCD_VCC_3.3V";
> regulator-min-microvolt = <2800000>;
> regulator-max-microvolt = <2800000>;
> - regulator-mem-idle;
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + };
LDC_VCC_3.3V may not be used in susepnd state. I think this regulator should
turn off in suspend state.
> };
>
> ldo26_reg: ldo26 {
> @@ -432,7 +483,9 @@
> regulator-name = "MOTOR_VCC_3.0V";
> regulator-min-microvolt = <3000000>;
> regulator-max-microvolt = <3000000>;
> - regulator-mem-idle;
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + };
If MOTOR_VCC_3.0V is used for haptic, I think this regulator should turn off in
suspend state.
> };
>
> buck1_reg: buck1 {
> @@ -442,7 +495,9 @@
> regulator-max-microvolt = <1100000>;
> regulator-always-on;
> regulator-boot-on;
> - regulator-mem-off;
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> };
>
> buck2_reg: buck2 {
> @@ -452,7 +507,9 @@
> regulator-max-microvolt = <1500000>;
> regulator-always-on;
> regulator-boot-on;
> - regulator-mem-off;
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + };
> };
>
> buck3_reg: buck3 {
> @@ -462,7 +519,9 @@
> regulator-max-microvolt = <1150000>;
> regulator-always-on;
> regulator-boot-on;
> - regulator-mem-off;
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> };
>
> buck4_reg: buck4 {
> @@ -471,7 +530,9 @@
> regulator-min-microvolt = <850000>;
> regulator-max-microvolt = <1150000>;
> regulator-boot-on;
> - regulator-mem-off;
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> };
>
> buck5_reg: buck5 {
> @@ -480,6 +541,9 @@
> regulator-min-microvolt = <1200000>;
> regulator-max-microvolt = <1200000>;
> regulator-always-on;
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + };
> };
>
> buck6_reg: buck6 {
> @@ -488,6 +552,9 @@
> regulator-min-microvolt = <1350000>;
> regulator-max-microvolt = <1350000>;
> regulator-always-on;
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + };
> };
>
> buck7_reg: buck7 {
> @@ -496,6 +563,9 @@
> regulator-min-microvolt = <2000000>;
> regulator-max-microvolt = <2000000>;
> regulator-always-on;
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + };
> };
>
> buck8_reg: buck8 {
> @@ -503,6 +573,9 @@
> regulator-name = "VMEM_VDDF_3.0V";
> regulator-min-microvolt = <2850000>;
> regulator-max-microvolt = <2850000>;
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + };
> };
>
> buck9_reg: buck9 {
> @@ -510,7 +583,9 @@
> regulator-name = "CAM_ISP_CORE_1.2V";
> regulator-min-microvolt = <1000000>;
> regulator-max-microvolt = <1200000>;
> - regulator-mem-off;
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> };
> };
> };
>
Thanks,
Chanwoo Choi
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
