2.6.12-rc2 still does not boot properly on my box. Hubert Tonneau wrote: > > When switching from 2.6.11 to 2.6.12-rc1, > I get a 'cannot open root device' fatal error at end of kernel boot process. > Root device is 'hda1'. > > Hardware content of the box: > > 8086 Intel Corporation 3340 82855PM 0 > Host-Hub Interface Bridge > 8086 Intel Corporation 3341 82855PM 0 AGP > Bridge > 8086 Intel Corporation 24C2 82801DB/DBL/DBM B > USB UHCI Controller #1 > 8086 Intel Corporation 24C4 82801DB/DBL/DBM B > USB UHCI Controller #2 > 8086 Intel Corporation 24C7 82801DB/DBL/DBM B > USB UHCI Controller #3 > 8086 Intel Corporation 24CD 82801DB/DBL/DBM B > USB EHCI Controller > 8086 Intel Corporation 2448 82801BAM/CAM/DBM 0 > Hub Interface to PCI Bridge > 8086 Intel Corporation 24CC 82801DBM 0 LPC > Interface Bridge > 8086 Intel Corporation 24CA 82801DBM B IDE > Controller (UltraATA/100) > 8086 Intel Corporation 24C5 82801DB/DBL/DBM B > AC97 Audio Controller > 8086 Intel Corporation 24C6 82801DB/DBM B AC97 > Modem Controller > 10DE NVIDIA Corporation 0324 NV31 B NVIDIA NV31GL > 14E4 Broadcom Corporation 165D BCM5705M B > Broadcom NetXtreme Gigabit Ethernet > 104C Texas Instruments AC47 7510/4510 B Cardbus > 104C Texas Instruments AC4A B > 104C Texas Instruments 802B B > 104C Texas Instruments 8204 4610, 4515, 4610FM 0 > TI UltraMedia Firmware Loader Device > 8086 Intel Corporation 4220 MPCI3B B Intel 2200 mPCI > 3B - RoW > > 2.6.11 kernel report: > > <4>Linux version 2.6.11 ([EMAIL PROTECTED]) (gcc version 3.3 (Debian)) #1 Sun > Mar 6 12:00:57 CET 2005 > <6>BIOS-provided physical RAM map: > <4> BIOS-e820: 0000000000000000 - 000000000009f000 (usable) > <4> BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved) > <4> BIOS-e820: 0000000000100000 - 000000003ffae000 (usable) > <4> BIOS-e820: 000000003ffae000 - 0000000040000000 (reserved) > <4> BIOS-e820: 00000000feda0000 - 00000000fee00000 (reserved) > <4> BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved) > <4>Warning only 896MB will be used. > <4>Use a HIGHMEM enabled kernel. > <5>896MB LOWMEM available. > <7>On node 0 totalpages: 229376 > <7> DMA zone: 4096 pages, LIFO batch:1 > <7> Normal zone: 225280 pages, LIFO batch:16 > <7> HighMem zone: 0 pages, LIFO batch:1 > <6>DMI 2.3 present. > <7>ACPI: RSDP (v000 DELL ) @ 0x000fdf00 > <7>ACPI: RSDT (v001 DELL CPi R 0x27d40903 ASL 0x00000061) @ 0x3fff0000 > <7>ACPI: FADT (v001 DELL CPi R 0x27d40903 ASL 0x00000061) @ 0x3fff0400 > <7>ACPI: ASF! (v016 DELL CPi R 0x27d40903 ASL 0x00000061) @ 0x3fff0800 > <7>ACPI: DSDT (v001 INT430 SYSFexxx 0x00001001 MSFT 0x0100000e) @ 0x00000000 > <4>Allocating PCI resources starting at 40000000 (gap: 40000000:beda0000) > <4>Built 1 zonelists > <4>Kernel command line: BOOT_IMAGE=recover ro root=301 > <4>Local APIC disabled by BIOS -- you can enable it with "lapic" > <7>mapped APIC to ffffd000 (01703000) > <6>Initializing CPU#0 > <4>PID hash table entries: 4096 (order: 12, 65536 bytes) > <4>Detected 1998.546 MHz processor. > <6>Using tsc for high-res timesource > <4>Console: colour VGA+ 80x25 > <4>Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) > <4>Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) > <6>Memory: 906620k/917504k available (1598k kernel code, 10432k reserved, > 518k data, 140k init, 0k highmem) > <4>Checking if this processor honours the WP bit even in supervisor mode... > Ok. > <7>Calibrating delay loop... 3956.73 BogoMIPS (lpj=1978368) > <4>Mount-cache hash table entries: 512 (order: 0, 4096 bytes) > <7>CPU: After generic identify, caps: afe9f9bf 00000000 00000000 00000000 > 00000180 00000000 00000000 > <7>CPU: After vendor identify, caps: afe9f9bf 00000000 00000000 00000000 > 00000180 00000000 00000000 > <6>CPU: L1 I cache: 32K, L1 D cache: 32K > <6>CPU: L2 cache: 2048K > <7>CPU: After all inits, caps: afe9f9bf 00000000 00000000 00000040 00000180 > 00000000 00000000 > <6>Intel machine check architecture supported. > <6>Intel machine check reporting enabled on CPU#0. > <4>CPU: Intel(R) Pentium(R) M processor 2.00GHz stepping 06 > <6>Enabling fast FPU save and restore... done. > <6>Enabling unmasked SIMD FPU exception support... done. > <6>Checking 'hlt' instruction... OK. > <4>ACPI: setting ELCR to 0200 (from 0800) > <6>NET: Registered protocol family 16 > <6>PCI: PCI BIOS revision 2.10 entry at 0xfc96e, last bus=2 > <6>PCI: Using configuration type 1 > <6>mtrr: v2.0 (20020519) > <6>ACPI: Subsystem revision 20050211 > <6>ACPI: Interpreter enabled > <6>ACPI: Using PIC for interrupt routing > <6>ACPI: PCI Root Bridge [PCI0] (00:00) > <4>PCI: Probing PCI hardware (bus 00) > <6>PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1 > <6>PCI: Transparent bridge - 0000:00:1e.0 > <7>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] > <4>ACPI: PCI Interrupt Link [LNKA] (IRQs 9 10 *11) > <4>ACPI: PCI Interrupt Link [LNKB] (IRQs 5 7) *11 > <4>ACPI: PCI Interrupt Link [LNKC] (IRQs 9 10 *11) > <4>ACPI: PCI Interrupt Link [LNKD] (IRQs 5 7 9 10 *11) > <4>ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, > disabled. > <4>ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 *11 12 14 15) > <7>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT] > <7>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIE._PRT] > <6>Linux Kernel Card Services > <6> options: [pci] [cardbus] [pm] > <6>PCI: Using ACPI for IRQ routing > <6>** PCI interrupts are no longer routed automatically. If this > <6>** causes a device to stop working, it is probably because the > <6>** driver failed to call pci_enable_device(). As a temporary > <6>** workaround, the "pci=routeirq" argument restores the old > <6>** behavior. If this argument makes the device work again, > <6>** please email the output of "lspci" to [EMAIL PROTECTED] > <6>** so I can fix the driver. > <6>ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3] C4[C3]) > <6>ACPI: Processor [CPU0] (supports 8 throttling states) > <6>ACPI: Thermal Zone [THM] (79 C) > <6>Real Time Clock Driver v1.12 > <6>serio: i8042 AUX port at 0x60,0x64 irq 12 > <6>serio: i8042 KBD port at 0x60,0x64 irq 1 > <6>io scheduler noop registered > <6>io scheduler anticipatory registered > <6>io scheduler deadline registered > <6>io scheduler cfq registered > <6>tg3.c:v3.23 (February 15, 2005) > <4>ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11 > <4>PCI: setting IRQ 11 as level-triggered > <6>ACPI: PCI interrupt 0000:02:00.0[A] -> GSI 11 (level, low) -> IRQ 11 > <6>eth0: Tigon3 [partno(BCM95705A50) rev 3001 PHY(5705)] (PCI:33MHz:32-bit) > 10/100/1000BaseT Ethernet 00:11:43:64:67:27 > <6>eth0: RXcsums[1] LinkChgREG[1] MIirq[1] ASF[0] Split[0] WireSpeed[1] > TSOcap[1] > <6>Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 > <6>ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx > <6>ICH4: IDE controller at PCI slot 0000:00:1f.1 > <4>PCI: Enabling device 0000:00:1f.1 (0005 -> 0007) > <4>ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11 > <6>ACPI: PCI interrupt 0000:00:1f.1[A] -> GSI 11 (level, low) -> IRQ 11 > <6>ICH4: chipset revision 1 > <6>ICH4: not 100% native mode: will probe irqs later > <6> ide0: BM-DMA at 0xbfa0-0xbfa7, BIOS settings: hda:DMA, hdb:pio > <6> ide1: BM-DMA at 0xbfa8-0xbfaf, BIOS settings: hdc:DMA, hdd:pio > <7>Probing IDE interface ide0... > <4>hda: FUJITSU MHT2060AH, ATA DISK drive > <4>ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 > <7>Probing IDE interface ide1... > <4>hdc: HL-DT-STCD-RW/DVD-ROM GCC-4243N, ATAPI CD/DVD-ROM drive > <4>ide1 at 0x170-0x177,0x376 on irq 15 > <7>Probing IDE interface ide2... > <7>Probing IDE interface ide3... > <7>Probing IDE interface ide4... > <7>Probing IDE interface ide5... > <6>hda: max request size: 128KiB > <6>hda: 117210240 sectors (60011 MB) w/8192KiB Cache, CHS=65535/16/63, > UDMA(100) > <7>hda: cache flushes supported > <6> hda: hda1 > <4>PCI: Enabling device 0000:02:01.0 (0000 -> 0002) > <4>ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11 > <6>ACPI: PCI interrupt 0000:02:01.0[A] -> GSI 11 (level, low) -> IRQ 11 > <6>Yenta: CardBus bridge found at 0000:02:01.0 [1028:014e] > <6>Yenta: ISA IRQ mask 0x04f8, PCI irq 11 > <6>Socket status: 30000410 > <6>ACPI: PCI interrupt 0000:02:01.1[A] -> GSI 11 (level, low) -> IRQ 11 > <6>Yenta: CardBus bridge found at 0000:02:01.1 [1028:014e] > <6>Yenta: ISA IRQ mask 0x04f8, PCI irq 11 > <6>Socket status: 30000047 > <6>mice: PS/2 mouse device common for all mice > <6>input: AT Translated Set 2 keyboard on isa0060/serio0 > <6>ALPS Touchpad (Dualpoint) detected > <6>input: AlpsPS/2 ALPS TouchPad on isa0060/serio1 > <6>NET: Registered protocol family 2 > <6>IP: routing cache hash table of 8192 buckets, 64Kbytes > <4>TCP established hash table entries: 131072 (order: 8, 1048576 bytes) > <4>TCP bind hash table entries: 65536 (order: 6, 262144 bytes) > <6>TCP: Hash tables configured (established 131072 bind 65536) > <6>NET: Registered protocol family 1 > <6>NET: Registered protocol family 17 > <4>ACPI wakeup devices: > <4> LID PBTN PCI0 USB0 USB1 USB2 USB3 MODM PCIE > <6>ACPI: (supports S0 S1 S3 S4 S4bios S5) > <6>EXT3-fs: mounted filesystem with ordered data mode. > <4>VFS: Mounted root (ext3 filesystem) readonly. > <6>Freeing unused kernel memory: 140k freed > <6>kjournald starting. Commit interval 5 seconds > <6>EXT3 FS on hda1, internal journal > <6>cs: IO port probe 0xc00-0xcff: clean. > <6>cs: IO port probe 0xc00-0xcff: clean. > <6>cs: IO port probe 0x800-0x8ff: excluding 0x8c0-0x8e7 > <6>cs: IO port probe 0x800-0x8ff: excluding 0x8c0-0x8e7 > <6>cs: IO port probe 0x100-0x4ff: excluding 0x280-0x287 0x2f8-0x2ff > 0x378-0x37f 0x3f8-0x3ff 0x4d0-0x4d7 > <6>cs: IO port probe 0x100-0x4ff: excluding 0x280-0x287 0x2f8-0x2ff > 0x378-0x37f 0x3f8-0x3ff 0x4d0-0x4d7 > <6>cs: IO port probe 0xa00-0xaff: clean. > <6>cs: IO port probe 0xa00-0xaff: clean. > <6>cs: memory probe 0xa0000000-0xa0ffffff: clean. > <6>tg3: eth0: Link is up at 100 Mbps, full duplex. > <6>tg3: eth0: Flow control is off for TX and off for RX. > <6>usbcore: registered new driver usbfs > <6>usbcore: registered new driver hub > <6>USB Universal Host Controller Interface driver v2.2 > <6>ACPI: PCI interrupt 0000:00:1d.0[A] -> GSI 11 (level, low) -> IRQ 11 > <6>uhci_hcd 0000:00:1d.0: UHCI Host Controller > <7>PCI: Setting latency timer of device 0000:00:1d.0 to 64 > <6>uhci_hcd 0000:00:1d.0: irq 11, io base 0xbf80 > <6>uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1 > <6>hub 1-0:1.0: USB hub found > <6>hub 1-0:1.0: 2 ports detected > <6>ACPI: PCI interrupt 0000:00:1d.1[B] -> GSI 11 (level, low) -> IRQ 11 > <6>uhci_hcd 0000:00:1d.1: UHCI Host Controller > <7>PCI: Setting latency timer of device 0000:00:1d.1 to 64 > <6>uhci_hcd 0000:00:1d.1: irq 11, io base 0xbf40 > <6>uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2 > <6>hub 2-0:1.0: USB hub found > <6>hub 2-0:1.0: 2 ports detected > <6>ACPI: PCI interrupt 0000:00:1d.2[C] -> GSI 11 (level, low) -> IRQ 11 > <6>uhci_hcd 0000:00:1d.2: UHCI Host Controller > <7>PCI: Setting latency timer of device 0000:00:1d.2 to 64 > <6>uhci_hcd 0000:00:1d.2: irq 11, io base 0xbf20 > <6>uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3 > <6>hub 3-0:1.0: USB hub found > <6>hub 3-0:1.0: 2 ports detected > <6>usb 2-1: new low speed USB device using uhci_hcd and address 2 > <6>usbcore: registered new driver usbkbd > <6>drivers/usb/input/usbkbd.c: :USB HID Boot Protocol keyboard driver > <6>input: USB HIDBP Mouse 413c:3010 on usb-0000:00:1d.1-1 > <6>usbcore: registered new driver usbmouse > <6>drivers/usb/input/usbmouse.c: v1.6:USB HID Boot Protocol mouse driver > <4>Warning: CPU frequency is 2000000, cpufreq assumed 1800000 kHz. > <4>Warning: CPU frequency is 2000000, cpufreq assumed 1800000 kHz. > <4>Warning: CPU frequency is 2000000, cpufreq assumed 1800000 kHz. > <4>Warning: CPU frequency is 2000000, cpufreq assumed 1800000 kHz. > <4>Warning: CPU frequency is 2000000, cpufreq assumed 1800000 kHz. > <4>Warning: CPU frequency is 2000000, cpufreq assumed 1800000 kHz. > <4>Warning: CPU frequency is 2000000, cpufreq assumed 1600000 kHz. > > Kernel settings: > > CONFIG_1GB: y > CONFIG_ACPI: y > CONFIG_ACPI_AC: m > CONFIG_ACPI_BATTERY: m > CONFIG_ACPI_BUTTON: m > CONFIG_ACPI_FAN: m > CONFIG_ACPI_PROCESSOR: y > CONFIG_ACPI_SLEEP: y > CONFIG_ACPI_THERMAL: y > CONFIG_ACPI_VIDEO: m > CONFIG_ACT200L_DONGLE: m > CONFIG_ACTISYS_DONGLE: m > CONFIG_APM_RTC_IS_GMT: y > CONFIG_ATALK: m > CONFIG_AUTOFS_FS: m > CONFIG_BINFMT_ELF: y > CONFIG_BINFMT_MISC: y > CONFIG_BLK_DEV_CMD640: y > CONFIG_BLK_DEV_FD: m > CONFIG_BLK_DEV_GENERIC: y > CONFIG_BLK_DEV_IDE: y > CONFIG_BLK_DEV_IDECD: m > CONFIG_BLK_DEV_IDECS: m > CONFIG_BLK_DEV_IDEDISK: y > CONFIG_BLK_DEV_IDEDMA: y > CONFIG_BLK_DEV_IDEDMA_PCI: y > CONFIG_BLK_DEV_IDEPCI: y > CONFIG_BLK_DEV_IDESCSI: m > CONFIG_BLK_DEV_LOOP: m > CONFIG_BLK_DEV_NBD: m > CONFIG_BLK_DEV_PIIX: y > CONFIG_BLK_DEV_RAM: m > CONFIG_BLK_DEV_RZ1000: y > CONFIG_BLK_DEV_SD: m > CONFIG_BLK_DEV_SR: m > CONFIG_BLK_DEV_TRIRON: y > CONFIG_BSD_PROCESS_ACCT: y > CONFIG_CARDBUS: y > CONFIG_CHR_DEV_SG: m > CONFIG_CODA_FS: m > CONFIG_CPU_FREQ: y > CONFIG_CPU_FREQ_DEFAULT_GOV_USERSPACE: y > CONFIG_CPU_FREQ_GOV_ONDEMAND: m > CONFIG_CPU_FREQ_GOV_PERFORMANCE: m > CONFIG_CPU_FREQ_GOV_POWERSAVE: m > CONFIG_CPU_FREQ_GOV_USERSPACE: y > CONFIG_CPU_FREQ_TABLE: y > CONFIG_DONGLE: m > CONFIG_DUMMY_CONSOLE: y > CONFIG_ESI_DONGLE: m > CONFIG_EXPERIMENTAL: y > CONFIG_EXT2_FS: y > CONFIG_EXT3_FS: y > CONFIG_EXT3_FS_XATTR: y > CONFIG_FAT_FS: m > CONFIG_FB: y > CONFIG_FB_ATY: m > CONFIG_FB_ATY128: m > CONFIG_FB_I810: m > CONFIG_FB_INTEL: m > CONFIG_FB_MATROX: m > CONFIG_FB_MODE_HELPER: y > CONFIG_FB_RADEON: m > CONFIG_FB_RIVA: m > CONFIG_FB_RIVA_I2C: y > CONFIG_FB_VESA: y > CONFIG_FILTER: y > CONFIG_FRAMEBUFFER_CONSOLE: y > CONFIG_GIRBIL_DONGLE: m > CONFIG_HFSPLUS_FS: m > CONFIG_HFS_FS: m > CONFIG_HOTPLUG: y > CONFIG_HPET_TIMER: y > CONFIG_HPFS_FS: m > CONFIG_IDE: y > CONFIG_IDEDMA_AUTO: y > CONFIG_IDEDMA_ONLYDISK: y > CONFIG_IDEDMA_PCI_AUTO: y > CONFIG_IDEPCI_SHARE_IRQ: y > CONFIG_IDE_GENERIC: y > CONFIG_INET: y > CONFIG_INPUT: y > CONFIG_INPUT_KEYBDEV: m > CONFIG_INPUT_KEYBOARD: y > CONFIG_INPUT_MOUSE: y > CONFIG_INPUT_MOUSEDEV: m > CONFIG_IP_ALIAS: y > CONFIG_IP_ROUTE_VERBOSE: y > CONFIG_IRCOMM: m > CONFIG_IRDA: m > CONFIG_IRDA_CACHE_LAST_LSAP: y > CONFIG_IRDA_DEBUG: y > CONFIG_IRDA_FAST_RR: y > CONFIG_IRLAN: m > CONFIG_IRPORT_SIR: m > CONFIG_IRQBALANCE: y > CONFIG_IRTTY_SIR: m > CONFIG_ISA: y > CONFIG_ISO9660_FS: m > CONFIG_KCORE_ELF: y > CONFIG_KEYBOARD_ATKBD: y > CONFIG_LEGACY_PTYS: y > CONFIG_LITELINK_DONGLE: m > CONFIG_LOCKD: m > CONFIG_M386: n > CONFIG_M486: n > CONFIG_M586: n > CONFIG_M686: n > CONFIG_MA600_DONGLE: m > CONFIG_MAC_PARTITION: y > CONFIG_MCP2120_DONGLE: m > CONFIG_MODULES: y > CONFIG_MODULE_UNLOAD: y > CONFIG_MOUSE: m > CONFIG_MOUSE_PS2: y > CONFIG_MPENTIUMM: y > CONFIG_MSDOS_FS: m > CONFIG_MTRR: y > CONFIG_NET: y > CONFIG_NETDEVICES: y > CONFIG_NET_ETHERNET: y > CONFIG_NFSD: m > CONFIG_NFS_FS: m > CONFIG_NLS: y > CONFIG_NLS_CODEPAGE_437: m > CONFIG_NLS_CODEPAGE_850: m > CONFIG_NLS_ISO8859_1: m > CONFIG_NLS_UTF8: m > CONFIG_NOHIGHMEM: y > CONFIG_NTFS_FS: m > CONFIG_OLD_BELKIN_DONGLE: m > CONFIG_OOM_KILLER: y > CONFIG_PACKET: y > CONFIG_PARPORT: m > CONFIG_PARPORT_PC: m > CONFIG_PCCARD: y > CONFIG_PCI: y > CONFIG_PCI_BIOS: y > CONFIG_PCI_GOANY: y > CONFIG_PCI_OLD_PROC: y > CONFIG_PCI_QUIRKS: y > CONFIG_PCMCIA: y > CONFIG_PIIX_TUNING: y > CONFIG_PM: y > CONFIG_PPP: m > CONFIG_PPPOE: m > CONFIG_PPP_ASYNC: m > CONFIG_PPP_BSDCOMP: m > CONFIG_PPP_DEFLATE: m > CONFIG_PPP_FILTER: y > CONFIG_PPP_SYNC_TTY: m > CONFIG_PREEMPT: y > CONFIG_PRINTER: m > CONFIG_PRINTER_READBACK: y > CONFIG_PROC_FS: y > CONFIG_PSMOUSE: y > CONFIG_QNX4FS_FS: m > CONFIG_REGPARM: y > CONFIG_RTC: y > CONFIG_SCSI: m > CONFIG_SCSI_PROC_FS: y > CONFIG_SERIAL: m > CONFIG_SERIAL_8250: m > CONFIG_SERIAL_8250_CS: m > CONFIG_SHAPER: m > CONFIG_SLIP: m > CONFIG_SMB_FS: m > CONFIG_SMC_IRCC_FIR: m > CONFIG_SND: m > CONFIG_SND_INTEL8X0: m > CONFIG_SND_MIXER_OSS: m > CONFIG_SND_PCM_OSS: m > CONFIG_SND_RTCTIMER: m > CONFIG_SND_SEQUENCER: m > CONFIG_SND_SEQUENCER_OSS: y > CONFIG_SND_SEQ_DUMMY: m > CONFIG_SND_USB_AUDIO: m > CONFIG_SOUND: m > CONFIG_SOUND_ICH: m > CONFIG_SUNRPC: m > CONFIG_SYSCTL: y > CONFIG_SYSVIPC: y > CONFIG_TEKRAM_DONGLE: m > CONFIG_TIGON3: y > CONFIG_UFS_FS: m > CONFIG_UMSDOS_FS: m > CONFIG_UNIX: y > CONFIG_USB: m > CONFIG_USB_ACM: m > CONFIG_USB_AUDIO: m > CONFIG_USB_CDCETHER: m > CONFIG_USB_DEVICEFS: y > CONFIG_USB_EHCI_HCD: m > CONFIG_USB_HID: y > CONFIG_USB_HIDINPUT: y > CONFIG_USB_KBD: m > CONFIG_USB_MOUSE: m > CONFIG_USB_OHCI: m > CONFIG_USB_OHCI_HCD: m > CONFIG_USB_PRINTER: m > CONFIG_USB_SERIAL: m > CONFIG_USB_STORAGE: m > CONFIG_USB_UHCI: m > CONFIG_USB_UHCI_ALT: m > CONFIG_USB_UHCI_HCD: m > CONFIG_VFAT_FS: m > CONFIG_VGA_CONSOLE: y > CONFIG_VIDEO_SELECT: y > CONFIG_VT: y > CONFIG_VT_CONSOLE: y > CONFIG_X86_MCE: y > CONFIG_X86_SPEEDSTEP_CENTRINO: y > CONFIG_X86_SPEEDSTEP_CENTRINO_ACPI: y > CONFIG_X86_UP_APIC: y > CONFIG_X86_UP_IOAPIC: y > CONFIG_YENTA: y > CONGIG_KMOD: y >
- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [EMAIL PROTECTED] More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
