As part of the migration we copy a few definitions from the mach-sa1100 headers and replace the automatic serial port detectiion with explicit configuration based on DEBUG_UART_PHYS/DEBUG_UART_VIRT.
The removal of the automatic configuration is similar to the way migration was handled for OMAP2 (see 808b7e07464d...). Signed-off-by: Daniel Thompson <[email protected]> Cc: Russell King <[email protected]> --- arch/arm/Kconfig.debug | 39 ++++++++++++++++++-- .../mach/debug-macro.S => include/debug/sa1100.S} | 41 +++++----------------- 2 files changed, 45 insertions(+), 35 deletions(-) rename arch/arm/{mach-sa1100/include/mach/debug-macro.S => include/debug/sa1100.S} (39%) diff --git a/arch/arm/Kconfig.debug b/arch/arm/Kconfig.debug index 3e1a491f6f29..3070498fb637 100644 --- a/arch/arm/Kconfig.debug +++ b/arch/arm/Kconfig.debug @@ -785,6 +785,30 @@ choice their output to UART 2. The port must have been initialised by the boot-loader before use. + config DEBUG_SA1100_UART1 + depends on ARCH_SA1100 + select DEBUG_SA1100_UART + bool "Kernel low-level debugging messages via SA1100 Ser1" + help + Say Y here if you want kernel low-level debugging support + on SA1100 based platforms. + + config DEBUG_SA1100_UART2 + depends on ARCH_SA1100 + select DEBUG_SA1100_UART + bool "Kernel low-level debugging messages via SA1100 Ser2" + help + Say Y here if you want kernel low-level debugging support + on SA1100 based platforms. + + config DEBUG_SA1100_UART3 + depends on ARCH_SA1100 + select DEBUG_SA1100_UART + bool "Kernel low-level debugging messages via SA1100 Ser3" + help + Say Y here if you want kernel low-level debugging support + on SA1100 based platforms. + config DEBUG_SOCFPGA_UART depends on ARCH_SOCFPGA bool "Use SOCFPGA UART for low-level debug" @@ -1088,6 +1112,10 @@ config DEBUG_TEGRA_UART bool depends on ARCH_TEGRA +config DEBUG_SA1100_UART + bool + depends on ARCH_SA1100 + config DEBUG_STI_UART bool depends on ARCH_STI @@ -1118,6 +1146,7 @@ config DEBUG_LL_INCLUDE default "debug/omap2plus.S" if DEBUG_OMAP2PLUS_UART default "debug/s3c24xx.S" if DEBUG_S3C24XX_UART default "debug/s5pv210.S" if DEBUG_S5PV210_UART + default "debug/sa1100.S" if DEBUG_SA1100_UART default "debug/sirf.S" if DEBUG_SIRFPRIMA2_UART1 || DEBUG_SIRFMARCO_UART1 default "debug/sti.S" if DEBUG_STI_UART default "debug/tegra.S" if DEBUG_TEGRA_UART @@ -1190,6 +1219,9 @@ config DEBUG_UART_PHYS DEBUG_S3C2410_UART2) default 0x78000000 if DEBUG_CNS3XXX default 0x7c0003f8 if FOOTBRIDGE + default 0x80010000 if DEBUG_SA1100_UART1 + default 0x80030000 if DEBUG_SA1100_UART2 + default 0x80050000 if DEBUG_SA1100_UART3 default 0x80070000 if DEBUG_IMX23_UART default 0x80074000 if DEBUG_IMX28_UART default 0x80230000 if DEBUG_PICOXCELL_UART @@ -1230,7 +1262,7 @@ config DEBUG_UART_PHYS DEBUG_UART_8250 || DEBUG_UART_PL01X || DEBUG_MESON_UARTAO || \ DEBUG_MSM_UART || DEBUG_NETX_UART || \ DEBUG_QCOM_UARTDM || DEBUG_S3C24XX_UART || \ - DEBUG_UART_BCM63XX + DEBUG_SA1100_UART || DEBUG_UART_BCM63XX config DEBUG_UART_VIRT hex "Virtual base address of debug UART" @@ -1259,6 +1291,9 @@ config DEBUG_UART_VIRT default 0xf7fc9000 if DEBUG_BERLIN_UART default 0xf8007000 if DEBUG_HIP04_UART default 0xf8009000 if DEBUG_VEXPRESS_UART0_CA9 + default 0xf8010000 if DEBUG_SA1100_UART1 + default 0xf8030000 if DEBUG_SA1100_UART2 + default 0xf8050000 if DEBUG_SA1100_UART3 default 0xf8090000 if DEBUG_VEXPRESS_UART0_RS1 default 0xfa71e000 if DEBUG_QCOM_UARTDM default 0xfb002000 if DEBUG_CNS3XXX @@ -1308,7 +1343,7 @@ config DEBUG_UART_VIRT DEBUG_UART_8250 || DEBUG_UART_PL01X || DEBUG_MESON_UARTAO || \ DEBUG_MSM_UART || DEBUG_NETX_UART || \ DEBUG_QCOM_UARTDM || DEBUG_S3C24XX_UART || \ - DEBUG_UART_BCM63XX + DEBUG_SA1100_UART || DEBUG_UART_BCM63XX config DEBUG_UART_8250_SHIFT int "Register offset shift for the 8250 debug UART" diff --git a/arch/arm/mach-sa1100/include/mach/debug-macro.S b/arch/arm/include/debug/sa1100.S similarity index 39% rename from arch/arm/mach-sa1100/include/mach/debug-macro.S rename to arch/arm/include/debug/sa1100.S index 530772d937ad..6b5e1ce099d3 100644 --- a/arch/arm/mach-sa1100/include/mach/debug-macro.S +++ b/arch/arm/include/debug/sa1100.S @@ -1,5 +1,4 @@ -/* arch/arm/mach-sa1100/include/mach/debug-macro.S - * +/* * Debugging macro include header * * Copyright (C) 1994-1999 Russell King @@ -10,39 +9,15 @@ * published by the Free Software Foundation. * */ -#include <mach/hardware.h> - - .macro addruart, rp, rv, tmp - mrc p15, 0, \rp, c1, c0 - tst \rp, #1 @ MMU enabled? - moveq \rp, #0x80000000 @ physical base address - movne \rp, #0xf8000000 @ virtual address - - @ We probe for the active serial port here, coherently with - @ the comment in arch/arm/mach-sa1100/include/mach/uncompress.h. - @ We assume r1 can be clobbered. - @ see if Ser3 is active - add \rp, \rp, #0x00050000 - ldr \rv, [\rp, #UTCR3] - tst \rv, #UTCR3_TXE - - @ if Ser3 is inactive, then try Ser1 - addeq \rp, \rp, #(0x00010000 - 0x00050000) - ldreq \rv, [\rp, #UTCR3] - tsteq \rv, #UTCR3_TXE - - @ if Ser1 is inactive, then try Ser2 - addeq \rp, \rp, #(0x00030000 - 0x00010000) - ldreq \rv, [\rp, #UTCR3] - tsteq \rv, #UTCR3_TXE - - @ clear top bits, and generate both phys and virt addresses - lsl \rp, \rp, #8 - lsr \rp, \rp, #8 - orr \rv, \rp, #0xf8000000 @ virtual - orr \rp, \rp, #0x80000000 @ physical +#define UTDR 0x14 +#define UTSR1 0x20 +#define UTSR1_TBY 0x00000001 /* Transmitter BusY (read) */ +#define UTSR1_TNF 0x00000004 /* Transmit FIFO Not Full (read) */ + .macro addruart, rp, rv, tmp + ldr \rp, =CONFIG_DEBUG_UART_PHYS + ldr \rv, =CONFIG_DEBUG_UART_VIRT .endm .macro senduart,rd,rx -- 1.9.3 -- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
