Based on the datasheet found here:
http://www.ti.com/lit/ds/symlink/bq24257.pdf
Signed-off-by: Laurentiu Palcu <laurentiu.pa...@intel.com>
---
Changes since v1:
* removed redundant bq24257_is_writeable_reg();
* made power_supply_desc struct a static const, since it's not changed;
laurentiu
.../devicetree/bindings/power/bq24257.txt | 21 +
drivers/power/Kconfig | 7 +
drivers/power/Makefile | 1 +
drivers/power/bq24257_charger.c | 863 +++++++++++++++++++++
4 files changed, 892 insertions(+)
create mode 100644 Documentation/devicetree/bindings/power/bq24257.txt
create mode 100644 drivers/power/bq24257_charger.c
diff --git a/Documentation/devicetree/bindings/power/bq24257.txt
b/Documentation/devicetree/bindings/power/bq24257.txt
new file mode 100644
index 0000000..5c9d394
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/bq24257.txt
@@ -0,0 +1,21 @@
+Binding for TI bq24257 Li-Ion Charger
+
+Required properties:
+- compatible: Should contain one of the following:
+ * "ti,bq24257"
+- reg: integer, i2c address of the device.
+- ti,battery-regulation-voltage: integer, maximum charging voltage in uV.
+- ti,charge-current: integer, maximum charging current in uA.
+- ti,termination-current: integer, charge will be terminated when current in
+ constant-voltage phase drops below this value (in
uA).
+
+Example:
+
+bq24257 {
+ compatible = "ti,bq24257";
+ reg = <0x6a>;
+
+ ti,battery-regulation-voltage = <4200000>;
+ ti,charge-current = <1000000>;
+ ti,termination-current = <50000>;
+};
diff --git a/drivers/power/Kconfig b/drivers/power/Kconfig
index 4091fb0..20352a7 100644
--- a/drivers/power/Kconfig
+++ b/drivers/power/Kconfig
@@ -388,6 +388,13 @@ config CHARGER_BQ24190
help
Say Y to enable support for the TI BQ24190 battery charger.
+config CHARGER_BQ24257
+ tristate "TI BQ24257 battery charger driver"
+ depends on I2C && GPIOLIB
+ depends on REGMAP_I2C
+ help
+ Say Y to enable support for the TI BQ24257 battery charger.
+
config CHARGER_BQ24735
tristate "TI BQ24735 battery charger support"
depends on I2C && GPIOLIB
diff --git a/drivers/power/Makefile b/drivers/power/Makefile
index b7b0181..19a1f41 100644
--- a/drivers/power/Makefile
+++ b/drivers/power/Makefile
@@ -58,6 +58,7 @@ obj-$(CONFIG_CHARGER_MAX8997) += max8997_charger.o
obj-$(CONFIG_CHARGER_MAX8998) += max8998_charger.o
obj-$(CONFIG_CHARGER_BQ2415X) += bq2415x_charger.o
obj-$(CONFIG_CHARGER_BQ24190) += bq24190_charger.o
+obj-$(CONFIG_CHARGER_BQ24257) += bq24257_charger.o
obj-$(CONFIG_CHARGER_BQ24735) += bq24735-charger.o
obj-$(CONFIG_POWER_AVS) += avs/
obj-$(CONFIG_CHARGER_SMB347) += smb347-charger.o
diff --git a/drivers/power/bq24257_charger.c b/drivers/power/bq24257_charger.c
new file mode 100644
index 0000000..ce7f5bb
--- /dev/null
+++ b/drivers/power/bq24257_charger.c
@@ -0,0 +1,863 @@
+/*
+ * TI BQ24257 charger driver
+ *
+ * Copyright (C) 2015 Intel Corporation
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/i2c.h>
+#include <linux/power_supply.h>
+#include <linux/regmap.h>
+#include <linux/types.h>
+#include <linux/gpio/consumer.h>
+#include <linux/interrupt.h>
+#include <linux/delay.h>
+
+#include <linux/acpi.h>
+#include <linux/of.h>
+
+#define BQ24257_REG_1 0x00
+#define BQ24257_REG_2 0x01
+#define BQ24257_REG_3 0x02
+#define BQ24257_REG_4 0x03
+#define BQ24257_REG_5 0x04
+#define BQ24257_REG_6 0x05
+#define BQ24257_REG_7 0x06
+
+#define BQ24257_MANUFACTURER "Texas Instruments"
+#define BQ24257_STAT_IRQ "stat"
+#define BQ24257_PG_GPIO "pg"
+
+#define BQ24257_ILIM_SET_DELAY 1000 /* msec */
+
+enum bq24257_fields {
+ F_WD_FAULT, F_WD_EN, F_STAT, F_FAULT, /* REG 1 */
+ F_RESET, F_IILIMIT, F_EN_STAT, F_EN_TERM, F_CE, F_HZ_MODE, /* REG 2 */
+ F_VBAT, F_USB_DET, /* REG 3 */
+ F_ICHG, F_ITERM, /* REG 4 */
+ F_LOOP_STATUS, F_LOW_CHG, F_DPDM_EN, F_CE_STATUS, F_VINDPM, /* REG 5 */
+ F_X2_TMR_EN, F_TMR, F_SYSOFF, F_TS_STAT, /* REG 6 */
+ F_VOVP, F_CLR_VDP, F_FORCE_BATDET, F_FORCE_PTM, /* REG 7 */
+
+ F_MAX_FIELDS
+};
+
+/* initial field values, converted from uV/uA */
+struct bq24257_init_data {
+ u8 ichg; /* charge current */
+ u8 vbat; /* regulation voltage */
+ u8 iterm; /* termination current */
+};
+
+struct bq24257_state {
+ u8 status;
+ u8 fault;
+ bool power_good;
+};
+
+struct bq24257_device {
+ struct i2c_client *client;
+ struct device *dev;
+ struct power_supply *charger;
+
+ struct regmap *rmap;
+ struct regmap_field *rmap_fields[F_MAX_FIELDS];
+
+ struct gpio_desc *pg;
+
+ struct delayed_work iilimit_setup_work;
+
+ struct bq24257_init_data init_data;
+ struct bq24257_state state;
+
+ struct mutex lock; /* protect state data */
+};
+
+static bool bq24257_is_volatile_reg(struct device *dev, unsigned int reg)
+{
+ switch (reg) {
+ case BQ24257_REG_2:
+ case BQ24257_REG_4:
+ return false;
+
+ default:
+ return true;
+ }
+}
+
+static const struct regmap_config bq24257_regmap_config = {
+ .reg_bits = 8,
+ .val_bits = 8,
+
+ .max_register = BQ24257_REG_7,
+ .cache_type = REGCACHE_RBTREE,
+
+ .volatile_reg = bq24257_is_volatile_reg,
+};
+
+static const struct reg_field bq24257_reg_fields[] = {
+ /* REG 1 */
+ [F_WD_FAULT] = REG_FIELD(BQ24257_REG_1, 7, 7),
+ [F_WD_EN] = REG_FIELD(BQ24257_REG_1, 6, 6),
+ [F_STAT] = REG_FIELD(BQ24257_REG_1, 4, 5),
+ [F_FAULT] = REG_FIELD(BQ24257_REG_1, 0, 3),
+ /* REG 2 */
+ [F_RESET] = REG_FIELD(BQ24257_REG_2, 7, 7),
+ [F_IILIMIT] = REG_FIELD(BQ24257_REG_2, 4, 6),
+ [F_EN_STAT] = REG_FIELD(BQ24257_REG_2, 3, 3),
+ [F_EN_TERM] = REG_FIELD(BQ24257_REG_2, 2, 2),
+ [F_CE] = REG_FIELD(BQ24257_REG_2, 1, 1),
+ [F_HZ_MODE] = REG_FIELD(BQ24257_REG_2, 0, 0),
+ /* REG 3 */
+ [F_VBAT] = REG_FIELD(BQ24257_REG_3, 2, 7),
+ [F_USB_DET] = REG_FIELD(BQ24257_REG_3, 0, 1),
+ /* REG 4 */
+ [F_ICHG] = REG_FIELD(BQ24257_REG_4, 3, 7),
+ [F_ITERM] = REG_FIELD(BQ24257_REG_4, 0, 2),
+ /* REG 5 */
+ [F_LOOP_STATUS] = REG_FIELD(BQ24257_REG_5, 6, 7),
+ [F_LOW_CHG] = REG_FIELD(BQ24257_REG_5, 5, 5),
+ [F_DPDM_EN] = REG_FIELD(BQ24257_REG_5, 4, 4),
+ [F_CE_STATUS] = REG_FIELD(BQ24257_REG_5, 3, 3),
+ [F_VINDPM] = REG_FIELD(BQ24257_REG_5, 0, 2),
+ /* REG 6 */
+ [F_X2_TMR_EN] = REG_FIELD(BQ24257_REG_6, 7, 7),
+ [F_TMR] = REG_FIELD(BQ24257_REG_6, 5, 6),
+ [F_SYSOFF] = REG_FIELD(BQ24257_REG_6, 4, 4),
+ [F_TS_STAT] = REG_FIELD(BQ24257_REG_6, 0, 2),
+ /* REG 7 */
+ [F_VOVP] = REG_FIELD(BQ24257_REG_7, 5, 7),
+ [F_CLR_VDP] = REG_FIELD(BQ24257_REG_7, 4, 4),
+ [F_FORCE_BATDET] = REG_FIELD(BQ24257_REG_7, 3, 3),
+ [F_FORCE_PTM] = REG_FIELD(BQ24257_REG_7, 2, 2)
+};
+
+static const u32 bq24257_vbat_map[] = {
+ 3500000, 3520000, 3540000, 3560000, 3580000, 3600000, 3620000, 3640000,
+ 3660000, 3680000, 3700000, 3720000, 3740000, 3760000, 3780000, 3800000,
+ 3820000, 3840000, 3860000, 3880000, 3900000, 3920000, 3940000, 3960000,
+ 3980000, 4000000, 4020000, 4040000, 4060000, 4080000, 4100000, 4120000,
+ 4140000, 4160000, 4180000, 4200000, 4220000, 4240000, 4260000, 4280000,
+ 4300000, 4320000, 4340000, 4360000, 4380000, 4400000, 4420000, 4440000
+};
+
+#define BQ24257_VBAT_MAP_SIZE ARRAY_SIZE(bq24257_vbat_map)
+
+static const u32 bq24257_ichg_map[] = {
+ 500000, 550000, 600000, 650000, 700000, 750000, 800000, 850000, 900000,
+ 950000, 1000000, 1050000, 1100000, 1150000, 1200000, 1250000, 1300000,
+ 1350000, 1400000, 1450000, 1500000, 1550000, 1600000, 1650000, 1700000,
+ 1750000, 1800000, 1850000, 1900000, 1950000, 2000000
+};
+
+#define BQ24257_ICHG_MAP_SIZE ARRAY_SIZE(bq24257_ichg_map)
+
+static const u32 bq24257_iterm_map[] = {
+ 50000, 75000, 100000, 125000, 150000, 175000, 200000, 225000
+};
+
+#define BQ24257_ITERM_MAP_SIZE ARRAY_SIZE(bq24257_iterm_map)
+
+static int bq24257_field_read(struct bq24257_device *bq,
+ enum bq24257_fields field_id)
+{
+ int ret;
+ int val;
+
+ ret = regmap_field_read(bq->rmap_fields[field_id], &val);
+ if (ret < 0)
+ return ret;
+
+ return val;
+}
+
+static int bq24257_field_write(struct bq24257_device *bq,
+ enum bq24257_fields field_id, u8 val)
+{
+ return regmap_field_write(bq->rmap_fields[field_id], val);
+}
+
+static u8 bq24257_find_idx(u32 value, const u32 *map, u8 map_size)
+{
+ u8 idx;
+
+ for (idx = 1; idx < map_size; idx++)
+ if (value < map[idx])
+ break;
+
+ return idx - 1;
+}
+
+enum bq24257_status {
+ STATUS_READY,
+ STATUS_CHARGE_IN_PROGRESS,
+ STATUS_CHARGE_DONE,
+ STATUS_FAULT,
+};
+
+enum bq24257_fault {
+ FAULT_NORMAL,
+ FAULT_INPUT_OVP,
+ FAULT_INPUT_UVLO,
+ FAULT_SLEEP,
+ FAULT_BAT_TS,
+ FAULT_BAT_OVP,
+ FAULT_TS,
+ FAULT_TIMER,
+ FAULT_NO_BAT,
+ FAULT_ISET,
+ FAULT_INPUT_LDO_LOW,
+};
+
+static int bq24257_power_supply_get_property(struct power_supply *psy,
+ enum power_supply_property psp,
+ union power_supply_propval *val)
+{
+ struct bq24257_device *bq = power_supply_get_drvdata(psy);
+ struct bq24257_state state;
+
+ mutex_lock(&bq->lock);
+ state = bq->state;
+ mutex_unlock(&bq->lock);
+
+ switch (psp) {
+ case POWER_SUPPLY_PROP_STATUS:
+ if (!state.power_good)
+ val->intval = POWER_SUPPLY_STATUS_DISCHARGING;
+ else if (state.status == STATUS_READY)
+ val->intval = POWER_SUPPLY_STATUS_NOT_CHARGING;
+ else if (state.status == STATUS_CHARGE_IN_PROGRESS)
+ val->intval = POWER_SUPPLY_STATUS_CHARGING;
+ else if (state.status == STATUS_CHARGE_DONE)
+ val->intval = POWER_SUPPLY_STATUS_FULL;
+ else
+ val->intval = POWER_SUPPLY_STATUS_UNKNOWN;
+ break;
+
+ case POWER_SUPPLY_PROP_MANUFACTURER:
+ val->strval = BQ24257_MANUFACTURER;
+ break;
+
+ case POWER_SUPPLY_PROP_ONLINE:
+ val->intval = state.power_good;
+ break;
+
+ case POWER_SUPPLY_PROP_HEALTH:
+ switch (state.fault) {
+ case FAULT_NORMAL:
+ val->intval = POWER_SUPPLY_HEALTH_GOOD;
+ break;
+
+ case FAULT_INPUT_OVP:
+ case FAULT_BAT_OVP:
+ val->intval = POWER_SUPPLY_HEALTH_OVERVOLTAGE;
+ break;
+
+ case FAULT_TS:
+ case FAULT_BAT_TS:
+ val->intval = POWER_SUPPLY_HEALTH_OVERHEAT;
+ break;
+
+ case FAULT_TIMER:
+ val->intval = POWER_SUPPLY_HEALTH_SAFETY_TIMER_EXPIRE;
+ break;
+
+ default:
+ val->intval = POWER_SUPPLY_HEALTH_UNSPEC_FAILURE;
+ break;
+ }
+
+ break;
+
+ case POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT:
+ val->intval = bq24257_ichg_map[bq->init_data.ichg];
+ break;
+
+ case POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT_MAX:
+ val->intval = bq24257_ichg_map[BQ24257_ICHG_MAP_SIZE - 1];
+ break;
+
+ case POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE:
+ val->intval = bq24257_vbat_map[bq->init_data.vbat];
+ break;
+
+ case POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE_MAX:
+ val->intval = bq24257_vbat_map[BQ24257_VBAT_MAP_SIZE - 1];
+ break;
+
+ case POWER_SUPPLY_PROP_CHARGE_TERM_CURRENT:
+ val->intval = bq24257_iterm_map[bq->init_data.iterm];
+ break;
+
+ default:
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static int bq24257_get_chip_state(struct bq24257_device *bq,
+ struct bq24257_state *state)
+{
+ int ret;
+
+ ret = bq24257_field_read(bq, F_STAT);
+ if (ret < 0)
+ return ret;
+
+ state->status = ret;
+
+ ret = bq24257_field_read(bq, F_FAULT);
+ if (ret < 0)
+ return ret;
+
+ state->fault = ret;
+
+ state->power_good = !gpiod_get_value_cansleep(bq->pg);
+
+ return 0;
+}
+
+static bool bq24257_state_changed(struct bq24257_device *bq,
+ struct bq24257_state *new_state)
+{
+ int ret;
+
+ mutex_lock(&bq->lock);
+ ret = (bq->state.status != new_state->status ||
+ bq->state.fault != new_state->fault ||
+ bq->state.power_good != new_state->power_good);
+ mutex_unlock(&bq->lock);
+
+ return ret;
+}
+
+enum bq24257_loop_status {
+ LOOP_STATUS_NONE,
+ LOOP_STATUS_IN_DPM,
+ LOOP_STATUS_IN_CURRENT_LIMIT,
+ LOOP_STATUS_THERMAL,
+};
+
+enum bq24257_in_ilimit {
+ IILIMIT_100,
+ IILIMIT_150,
+ IILIMIT_500,
+ IILIMIT_900,
+ IILIMIT_1500,
+ IILIMIT_2000,
+ IILIMIT_EXT,
+ IILIMIT_NONE,
+};
+
+enum bq24257_port_type {
+ PORT_TYPE_DCP, /* Dedicated Charging Port */
+ PORT_TYPE_CDP, /* Charging Downstream Port */
+ PORT_TYPE_SDP, /* Standard Downstream Port */
+ PORT_TYPE_NON_STANDARD,
+};
+
+enum bq24257_safety_timer {
+ SAFETY_TIMER_45,
+ SAFETY_TIMER_360,
+ SAFETY_TIMER_540,
+ SAFETY_TIMER_NONE,
+};
+
+static int bq24257_iilimit_autoset(struct bq24257_device *bq)
+{
+ int loop_status;
+ int iilimit;
+ int port_type;
+ int ret;
+ const u8 new_iilimit[] = {
+ [PORT_TYPE_DCP] = IILIMIT_2000,
+ [PORT_TYPE_CDP] = IILIMIT_2000,
+ [PORT_TYPE_SDP] = IILIMIT_500,
+ [PORT_TYPE_NON_STANDARD] = IILIMIT_500
+ };
+
+ ret = bq24257_field_read(bq, F_LOOP_STATUS);
+ if (ret < 0)
+ goto error;
+
+ loop_status = ret;
+
+ ret = bq24257_field_read(bq, F_IILIMIT);
+ if (ret < 0)
+ goto error;
+
+ iilimit = ret;
+
+ /*
+ * All USB ports should be able to handle 500mA. If not, DPM will lower
+ * the charging current to accommodate the power source. No need to set
+ * a lower IILIMIT value.
+ */
+ if (loop_status == LOOP_STATUS_IN_DPM && iilimit == IILIMIT_500)
+ return 0;
+
+ ret = bq24257_field_read(bq, F_USB_DET);
+ if (ret < 0)
+ goto error;
+
+ port_type = ret;
+
+ ret = bq24257_field_write(bq, F_IILIMIT, new_iilimit[port_type]);
+ if (ret < 0)
+ goto error;
+
+ ret = bq24257_field_write(bq, F_TMR, SAFETY_TIMER_360);
+ if (ret < 0)
+ goto error;
+
+ ret = bq24257_field_write(bq, F_CLR_VDP, 1);
+ if (ret < 0)
+ goto error;
+
+ dev_dbg(bq->dev, "port/loop = %d/%d -> iilimit = %d\n",
+ port_type, loop_status, new_iilimit[port_type]);
+
+ return 0;
+
+error:
+ dev_err(bq->dev, "%s: Error communicating with the chip.\n", __func__);
+ return ret;
+}
+
+static void bq24257_iilimit_setup_work(struct work_struct *work)
+{
+ struct bq24257_device *bq = container_of(work, struct bq24257_device,
+ iilimit_setup_work.work);
+
+ bq24257_iilimit_autoset(bq);
+}
+
+static void bq24257_handle_state_change(struct bq24257_device *bq,
+ struct bq24257_state *new_state)
+{
+ int ret;
+ struct bq24257_state old_state;
+ bool reset_iilimit = false;
+ bool config_iilimit = false;
+
+ mutex_lock(&bq->lock);
+ old_state = bq->state;
+ mutex_unlock(&bq->lock);
+
+ if (!new_state->power_good) { /* power removed */
+ cancel_delayed_work_sync(&bq->iilimit_setup_work);
+
+ /* activate D+/D- port detection algorithm */
+ ret = bq24257_field_write(bq, F_DPDM_EN, 1);
+ if (ret < 0)
+ goto error;
+
+ reset_iilimit = true;
+ } else if (!old_state.power_good) { /* power inserted */
+ config_iilimit = true;
+ } else if (new_state->fault == FAULT_NO_BAT) { /* battery removed */
+ cancel_delayed_work_sync(&bq->iilimit_setup_work);
+
+ reset_iilimit = true;
+ } else if (old_state.fault == FAULT_NO_BAT) { /* battery connected */
+ config_iilimit = true;
+ } else if (new_state->fault == FAULT_TIMER) { /* safety timer expired */
+ dev_err(bq->dev, "Safety timer expired! Battery dead?\n");
+ }
+
+ if (reset_iilimit) {
+ ret = bq24257_field_write(bq, F_IILIMIT, IILIMIT_500);
+ if (ret < 0)
+ goto error;
+ } else if (config_iilimit) {
+ schedule_delayed_work(&bq->iilimit_setup_work,
+ msecs_to_jiffies(BQ24257_ILIM_SET_DELAY));
+ }
+
+ return;
+
+error:
+ dev_err(bq->dev, "%s: Error communicating with the chip.\n", __func__);
+}
+
+static irqreturn_t bq24257_irq_handler_thread(int irq, void *private)
+{
+ int ret;
+ struct bq24257_device *bq = private;
+ struct bq24257_state state;
+
+ ret = bq24257_get_chip_state(bq, &state);
+ if (ret < 0)
+ return IRQ_HANDLED;
+
+ if (!bq24257_state_changed(bq, &state))
+ return IRQ_HANDLED;
+
+ dev_dbg(bq->dev, "irq(state changed): status/fault/pg = %d/%d/%d\n",
+ state.status, state.fault, state.power_good);
+
+ bq24257_handle_state_change(bq, &state);
+
+ mutex_lock(&bq->lock);
+ bq->state = state;
+ mutex_unlock(&bq->lock);
+
+ power_supply_changed(bq->charger);
+
+ return IRQ_HANDLED;
+}
+
+static int bq24257_hw_init(struct bq24257_device *bq)
+{
+ int ret;
+ int i;
+ struct bq24257_state state;
+
+ const struct {
+ int field;
+ u32 value;
+ } init_data[] = {
+ {F_ICHG, bq->init_data.ichg},
+ {F_VBAT, bq->init_data.vbat},
+ {F_ITERM, bq->init_data.iterm}
+ };
+
+ /*
+ * Disable the watchdog timer to prevent the IC from going back to
+ * default settings after 50 seconds of I2C inactivity.
+ */
+ ret = bq24257_field_write(bq, F_WD_EN, 0);
+ if (ret < 0)
+ return ret;
+
+ /* configure the charge currents and voltages */
+ for (i = 0; i < ARRAY_SIZE(init_data); i++) {
+ ret = bq24257_field_write(bq, init_data[i].field,
+ init_data[i].value);
+ if (ret < 0)
+ return ret;
+ }
+
+ ret = bq24257_get_chip_state(bq, &state);
+ if (ret < 0)
+ return ret;
+
+ mutex_lock(&bq->lock);
+ bq->state = state;
+ mutex_unlock(&bq->lock);
+
+ if (!state.power_good)
+ /* activate D+/D- detection algorithm */
+ ret = bq24257_field_write(bq, F_DPDM_EN, 1);
+ else if (state.fault != FAULT_NO_BAT)
+ ret = bq24257_iilimit_autoset(bq);
+
+ return ret;
+}
+
+static enum power_supply_property bq24257_power_supply_props[] = {
+ POWER_SUPPLY_PROP_MANUFACTURER,
+ POWER_SUPPLY_PROP_STATUS,
+ POWER_SUPPLY_PROP_ONLINE,
+ POWER_SUPPLY_PROP_HEALTH,
+ POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT,
+ POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT_MAX,
+ POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE,
+ POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE_MAX,
+ POWER_SUPPLY_PROP_CHARGE_TERM_CURRENT,
+};
+
+static char *bq24257_charger_supplied_to[] = {
+ "main-battery",
+};
+
+static const struct power_supply_desc bq24257_power_supply_desc = {
+ .name = "bq24257-charger",
+ .type = POWER_SUPPLY_TYPE_USB,
+ .properties = bq24257_power_supply_props,
+ .num_properties = ARRAY_SIZE(bq24257_power_supply_props),
+ .get_property = bq24257_power_supply_get_property,
+};
+
+static int bq24257_power_supply_init(struct bq24257_device *bq)
+{
+ struct power_supply_config psy_cfg = { .drv_data = bq, };
+
+ psy_cfg.supplied_to = bq24257_charger_supplied_to;
+ psy_cfg.num_supplicants = ARRAY_SIZE(bq24257_charger_supplied_to);
+
+ bq->charger = power_supply_register(bq->dev, &bq24257_power_supply_desc,
+ &psy_cfg);
+ if (IS_ERR(bq->charger))
+ return PTR_ERR(bq->charger);
+
+ return 0;
+}
+
+static int bq24257_irq_probe(struct bq24257_device *bq)
+{
+ int ret;
+ struct gpio_desc *stat_irq;
+
+ stat_irq = devm_gpiod_get_index(bq->dev, BQ24257_STAT_IRQ, 0);
+ if (IS_ERR(stat_irq)) {
+ dev_err(bq->dev, "could not probe stat_irq pin\n");
+ return PTR_ERR(stat_irq);
+ }
+
+ ret = gpiod_direction_input(stat_irq);
+ if (ret < 0)
+ return ret;
+
+ return gpiod_to_irq(stat_irq);
+}
+
+static int bq24257_pg_gpio_probe(struct bq24257_device *bq)
+{
+ bq->pg = devm_gpiod_get_index(bq->dev, BQ24257_PG_GPIO, 0);
+ if (IS_ERR(bq->pg)) {
+ dev_err(bq->dev, "could not probe PG pin\n");
+ return PTR_ERR(bq->pg);
+ }
+
+ return gpiod_direction_input(bq->pg);
+}
+
+static int bq24257_fw_probe(struct bq24257_device *bq)
+{
+ int ret;
+ u32 property;
+
+ ret = device_property_read_u32(bq->dev, "ti,charge-current", &property);
+ if (ret < 0)
+ return ret;
+
+ bq->init_data.ichg = bq24257_find_idx(property, bq24257_ichg_map,
+ BQ24257_ICHG_MAP_SIZE);
+
+ ret = device_property_read_u32(bq->dev, "ti,battery-regulation-voltage",
+ &property);
+ if (ret < 0)
+ return ret;
+
+ bq->init_data.vbat = bq24257_find_idx(property, bq24257_vbat_map,
+ BQ24257_VBAT_MAP_SIZE);
+
+ ret = device_property_read_u32(bq->dev, "ti,termination-current",
+ &property);
+ if (ret < 0)
+ return ret;
+
+ bq->init_data.iterm = bq24257_find_idx(property, bq24257_iterm_map,
+ BQ24257_ITERM_MAP_SIZE);
+
+ return 0;
+}
+
+static int bq24257_probe(struct i2c_client *client,
+ const struct i2c_device_id *id)
+{
+ struct i2c_adapter *adapter = to_i2c_adapter(client->dev.parent);
+ struct device *dev = &client->dev;
+ struct bq24257_device *bq;
+ int ret;
+ int i;
+
+ if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) {
+ dev_err(dev, "No support for SMBUS_BYTE_DATA\n");
+ return -ENODEV;
+ }
+
+ bq = devm_kzalloc(dev, sizeof(*bq), GFP_KERNEL);
+ if (!bq)
+ return -ENOMEM;
+
+ bq->client = client;
+ bq->dev = dev;
+
+ mutex_init(&bq->lock);
+
+ bq->rmap = devm_regmap_init_i2c(client, &bq24257_regmap_config);
+ if (IS_ERR(bq->rmap)) {
+ dev_err(dev, "failed to allocate register map\n");
+ return PTR_ERR(bq->rmap);
+ }
+
+ for (i = 0; i < ARRAY_SIZE(bq24257_reg_fields); i++) {
+ const struct reg_field *reg_fields = bq24257_reg_fields;
+
+ bq->rmap_fields[i] = devm_regmap_field_alloc(dev, bq->rmap,
+ reg_fields[i]);
+ if (IS_ERR(bq->rmap_fields[i])) {
+ dev_err(dev, "cannot allocate regmap field\n");
+ return PTR_ERR(bq->rmap_fields[i]);
+ }
+ }
+
+ i2c_set_clientdata(client, bq);
+
+ INIT_DELAYED_WORK(&bq->iilimit_setup_work, bq24257_iilimit_setup_work);
+
+ if (!dev->platform_data) {
+ ret = bq24257_fw_probe(bq);
+ if (ret < 0) {
+ dev_err(dev, "Cannot read device properties.\n");
+ return ret;
+ }
+ } else {
+ return -ENODEV;
+ }
+
+ /* we can only check Power Good status by probing the PG pin */
+ ret = bq24257_pg_gpio_probe(bq);
+ if (ret < 0)
+ return ret;
+
+ /* reset all registers to defaults */
+ ret = bq24257_field_write(bq, F_RESET, 1);
+ if (ret < 0)
+ return ret;
+
+ /*
+ * Put the RESET bit back to 0, in cache. For some reason the HW always
+ * returns 1 on this bit, so this is the only way to avoid resetting the
+ * chip every time we update another field in this register.
+ */
+ ret = bq24257_field_write(bq, F_RESET, 0);
+ if (ret < 0)
+ return ret;
+
+ ret = bq24257_hw_init(bq);
+ if (ret < 0) {
+ dev_err(dev, "Cannot initialize the chip.\n");
+ return ret;
+ }
+
+ if (client->irq <= 0)
+ client->irq = bq24257_irq_probe(bq);
+
+ if (client->irq < 0) {
+ dev_err(dev, "no irq resource found\n");
+ return client->irq;
+ }
+
+ ret = devm_request_threaded_irq(dev, client->irq, NULL,
+ bq24257_irq_handler_thread,
+ IRQF_TRIGGER_FALLING |
+ IRQF_TRIGGER_RISING | IRQF_ONESHOT,
+ BQ24257_STAT_IRQ, bq);
+ if (ret)
+ return ret;
+
+ ret = bq24257_power_supply_init(bq);
+ if (ret < 0)
+ dev_err(dev, "Failed to register power supply\n");
+
+ return ret;
+}
+
+static int bq24257_remove(struct i2c_client *client)
+{
+ struct bq24257_device *bq = i2c_get_clientdata(client);
+
+ cancel_delayed_work_sync(&bq->iilimit_setup_work);
+
+ power_supply_unregister(bq->charger);
+
+ bq24257_field_write(bq, F_RESET, 1); /* reset to defaults */
+
+ return 0;
+}
+
+#ifdef CONFIG_PM_SLEEP
+static int bq24257_suspend(struct device *dev)
+{
+ struct bq24257_device *bq = dev_get_drvdata(dev);
+ int ret = 0;
+
+ cancel_delayed_work_sync(&bq->iilimit_setup_work);
+
+ /* reset all registers to default (and activate standalone mode) */
+ ret = bq24257_field_write(bq, F_RESET, 1);
+ if (ret < 0)
+ dev_err(bq->dev, "Cannot reset chip to standalone mode.\n");
+
+ return ret;
+}
+
+static int bq24257_resume(struct device *dev)
+{
+ int ret;
+ struct bq24257_device *bq = dev_get_drvdata(dev);
+
+ ret = regcache_drop_region(bq->rmap, BQ24257_REG_1, BQ24257_REG_7);
+ if (ret < 0)
+ return ret;
+
+ ret = bq24257_field_write(bq, F_RESET, 0);
+ if (ret < 0)
+ return ret;
+
+ ret = bq24257_hw_init(bq);
+ if (ret < 0) {
+ dev_err(bq->dev, "Cannot init chip after resume.\n");
+ return ret;
+ }
+
+ /* signal userspace, maybe state changed while suspended */
+ power_supply_changed(bq->charger);
+
+ return 0;
+}
+#endif
+
+static const struct dev_pm_ops bq24257_pm = {
+ SET_SYSTEM_SLEEP_PM_OPS(bq24257_suspend, bq24257_resume)
+};
+
+static const struct i2c_device_id bq24257_i2c_ids[] = {
+ { "bq24257", 0 },
+ {},
+};
+MODULE_DEVICE_TABLE(i2c, bq24257_i2c_ids);
+
+static const struct of_device_id bq24257_of_match[] = {
+ { .compatible = "ti,bq24257", },
+ { },
+};
+MODULE_DEVICE_TABLE(of, bq24257_of_match);
+
+static const struct acpi_device_id bq24257_acpi_match[] = {
+ {"BQ242570", 0},
+ {},
+};
+MODULE_DEVICE_TABLE(acpi, bq24257_acpi_match);
+
+static struct i2c_driver bq24257_driver = {
+ .driver = {
+ .name = "bq24257-charger",
+ .of_match_table = of_match_ptr(bq24257_of_match),
+ .acpi_match_table = ACPI_PTR(bq24257_acpi_match),
+ .pm = &bq24257_pm,
+ },
+ .probe = bq24257_probe,
+ .remove = bq24257_remove,
+ .id_table = bq24257_i2c_ids,
+};
+module_i2c_driver(bq24257_driver);
+
+MODULE_AUTHOR("Laurentiu Palcu <laurentiu.pa...@intel.com>");
+MODULE_DESCRIPTION("bq24257 charger driver");
+MODULE_LICENSE("GPL");
--
1.9.1
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
