maar_init was previously only compiled when CONFIG_NEED_MULTIPLE_NODES was not set, which has been fine since it is only called from the standard implementation of mem_init which has the same condition. In preparation for calling it from the SMP startup code on secondary CPUs, move maar_init outside of the #ifndef such that it is always compiled.
Signed-off-by: Paul Burton <[email protected]> Cc: Markos Chandras <[email protected]> --- Changes in v2: - New patch, to fix ip27_defconfig builds. arch/mips/mm/init.c | 126 ++++++++++++++++++++++++++-------------------------- 1 file changed, 63 insertions(+), 63 deletions(-) diff --git a/arch/mips/mm/init.c b/arch/mips/mm/init.c index 66d0f49..074ac54 100644 --- a/arch/mips/mm/init.c +++ b/arch/mips/mm/init.c @@ -252,6 +252,69 @@ void __init fixrange_init(unsigned long start, unsigned long end, #endif } +unsigned __weak platform_maar_init(unsigned num_pairs) +{ + struct maar_config cfg[BOOT_MEM_MAP_MAX]; + unsigned i, num_configured, num_cfg = 0; + phys_addr_t skip; + + for (i = 0; i < boot_mem_map.nr_map; i++) { + switch (boot_mem_map.map[i].type) { + case BOOT_MEM_RAM: + case BOOT_MEM_INIT_RAM: + break; + default: + continue; + } + + skip = 0x10000 - (boot_mem_map.map[i].addr & 0xffff); + + cfg[num_cfg].lower = boot_mem_map.map[i].addr; + cfg[num_cfg].lower += skip; + + cfg[num_cfg].upper = cfg[num_cfg].lower; + cfg[num_cfg].upper += boot_mem_map.map[i].size - 1; + cfg[num_cfg].upper -= skip; + + cfg[num_cfg].attrs = MIPS_MAAR_S; + num_cfg++; + } + + num_configured = maar_config(cfg, num_cfg, num_pairs); + if (num_configured < num_cfg) + pr_warn("Not enough MAAR pairs (%u) for all bootmem regions (%u)\n", + num_pairs, num_cfg); + + return num_configured; +} + +static void maar_init(void) +{ + unsigned num_maars, used, i; + + if (!cpu_has_maar) + return; + + /* Detect the number of MAARs */ + write_c0_maari(~0); + back_to_back_c0_hazard(); + num_maars = read_c0_maari() + 1; + + /* MAARs should be in pairs */ + WARN_ON(num_maars % 2); + + /* Configure the required MAARs */ + used = platform_maar_init(num_maars / 2); + + /* Disable any further MAARs */ + for (i = (used * 2); i < num_maars; i++) { + write_c0_maari(i); + back_to_back_c0_hazard(); + write_c0_maar(0); + back_to_back_c0_hazard(); + } +} + #ifndef CONFIG_NEED_MULTIPLE_NODES int page_is_ram(unsigned long pagenr) { @@ -334,69 +397,6 @@ static inline void mem_init_free_highmem(void) #endif } -unsigned __weak platform_maar_init(unsigned num_pairs) -{ - struct maar_config cfg[BOOT_MEM_MAP_MAX]; - unsigned i, num_configured, num_cfg = 0; - phys_addr_t skip; - - for (i = 0; i < boot_mem_map.nr_map; i++) { - switch (boot_mem_map.map[i].type) { - case BOOT_MEM_RAM: - case BOOT_MEM_INIT_RAM: - break; - default: - continue; - } - - skip = 0x10000 - (boot_mem_map.map[i].addr & 0xffff); - - cfg[num_cfg].lower = boot_mem_map.map[i].addr; - cfg[num_cfg].lower += skip; - - cfg[num_cfg].upper = cfg[num_cfg].lower; - cfg[num_cfg].upper += boot_mem_map.map[i].size - 1; - cfg[num_cfg].upper -= skip; - - cfg[num_cfg].attrs = MIPS_MAAR_S; - num_cfg++; - } - - num_configured = maar_config(cfg, num_cfg, num_pairs); - if (num_configured < num_cfg) - pr_warn("Not enough MAAR pairs (%u) for all bootmem regions (%u)\n", - num_pairs, num_cfg); - - return num_configured; -} - -static void maar_init(void) -{ - unsigned num_maars, used, i; - - if (!cpu_has_maar) - return; - - /* Detect the number of MAARs */ - write_c0_maari(~0); - back_to_back_c0_hazard(); - num_maars = read_c0_maari() + 1; - - /* MAARs should be in pairs */ - WARN_ON(num_maars % 2); - - /* Configure the required MAARs */ - used = platform_maar_init(num_maars / 2); - - /* Disable any further MAARs */ - for (i = (used * 2); i < num_maars; i++) { - write_c0_maari(i); - back_to_back_c0_hazard(); - write_c0_maar(0); - back_to_back_c0_hazard(); - } -} - void __init mem_init(void) { #ifdef CONFIG_HIGHMEM -- 2.5.3 -- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
