This adds device tree binding documentation for the Broadcom BCM6328 LED controller.
Signed-off-by: Álvaro Fernández Rojas <[email protected]> Signed-off-by: Jonas Gorski <[email protected]> --- v3: introduce changes suggested by Jacek - Revert compatible string to "brcm,bcm6328-leds". - Improved description. - Renamed normal LEDs to hardware controlled. - Explain that LEDs are active high by default on active-low optional property. - Properties are now grouped depending on the type of LED and optional requirement. - Added more examples to explain hardware controlled LEDs and activity/link selection. v2: Introduce changes suggested by Florian and Jonas. - Change compatible string to "brcm,bcm6328-leds-ctrl". - Make valid LEDs statement more strict. - Remove compatible strings from LED subnodes. - Clarify that LEDs are active high by default. - Add a better description for brcm,link-signal-sources and brcm,activity-signal-sources. .../devicetree/bindings/leds/leds-bcm6328.txt | 311 +++++++++++++++++++++ 1 file changed, 311 insertions(+) create mode 100644 Documentation/devicetree/bindings/leds/leds-bcm6328.txt diff --git a/Documentation/devicetree/bindings/leds/leds-bcm6328.txt b/Documentation/devicetree/bindings/leds/leds-bcm6328.txt new file mode 100644 index 0000000..6d838f8 --- /dev/null +++ b/Documentation/devicetree/bindings/leds/leds-bcm6328.txt @@ -0,0 +1,311 @@ +LEDs connected to Broadcom BCM6328 controller + +This controller is present on BCM6318, BCM6328, BCM6362 and BCM63268. +In these SoCs it's possible to control LEDs both as GPIOs or by hardware. +However, on some devices there are Serial LEDs (LEDs connected to a 74x164 +controller), which can either be controlled by software (exporting the 74x164 +as spi-gpio. See Documentation/devicetree/bindings/gpio/gpio-74x164.txt), or +by hardware using this driver. +Some of these Serial LEDs are hardware controlled (e.g. ethernet LEDs) and +exporting the 74x164 as spi-gpio prevents those LEDs to be hardware +controlled, so the only chance to keep them working is by using this driver. + +BCM6328 LED controller has a HWDIS register, which controls whether a LED +should be controlled by a hardware signal instead of the MODE register value, +with 0 meaning hardware control enabled and 1 hardware control disabled. This +is usually 1:1 for hardware to LED signals, but through the activity/link +registers you have some limited control over rerouting the LEDs (as +explained later in brcm,link-signal-sources). Even if a LED is hardware +controlled you are still able to make it blink or light it up if it isn't, +but you can't turn it off if the hardware decides to light it up. For this +reason, hardware controlled LEDs aren't registered as LED class devices. + +Required properties: +- compatible: should be : "brcm,bcm6328-leds". +- #address-cells: must be 1 +- #size-cells: must be 0 +- reg: BCM6328 LED controller address and size. + +Optional properties: +- brcm,serial-leds: boolean which enables Serial LEDs. + +Each LED is represented as a sub-node of the brcm,bcm6328-leds device. + +LED sub-node required properties: +- reg: LED pin number (only LEDs 0 to 23 are valid). + +Software controlled LED optional properties: +- label (optional): see Documentation/devicetree/bindings/leds/common.txt +- active-low (optional): boolean that makes LED active low. + Default: false +- default-state (optional): see + Documentation/devicetree/bindings/leds/leds-gpio.txt +- linux,default-trigger (optional): see + Documentation/devicetree/bindings/leds/common.txt + +Hardware controlled LED optional properties: +- brcm,hardware-controlled: boolean that makes this LED hardware + controlled. +- brcm,link-signal-sources: An array of hardware link + signal sources. Up to four link hardware signals can get muxed into + these LEDs. Only valid for LEDs 0 to 7, where LED signals 0 to 3 may + be muxed to LEDs 0 to 3, and signals 4 to 7 may be muxed to LEDs + 4 to 7. A signal can be muxed to more than one LED, and one LED can + have more than one source signal. +- brcm,activity-signal-sources: An array of hardware activity + signal sources. Up to four activity hardware signals can get muxed into + these LEDs. Only valid for LEDs 0 to 7, where LED signals 0 to 3 may + be muxed to LEDs 0 to 3, and signals 4 to 7 may be muxed to LEDs + 4 to 7. A signal can be muxed to more than one LED, and one LED can + have more than one source signal. + +example 1) BCM6328 with 4 EPHY LEDs + +leds0: led-controller@10000800 { + compatible = "brcm,bcm6328-leds"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x10000800 0x24>; + + alarm_red@2 { + reg = <2>; + active-low; + label = "red:alarm"; + }; + inet_green@3 { + reg = <3>; + active-low; + label = "green:inet"; + }; + power_green@4 { + reg = <4>; + active-low; + label = "green:power"; + default-state = "on"; + }; + ephy0_spd@17 { + reg = <17>; + brcm,hardware-controlled; + }; + ephy1_spd@18 { + reg = <18>; + brcm,hardware-controlled; + }; + ephy2_spd@19 { + reg = <19>; + brcm,hardware-controlled; + }; + ephy3_spd@20 { + reg = <20>; + brcm,hardware-controlled; + }; +}; + +example 2) BCM63268 with Serial/GPHY0 LEDs + +leds0: led-controller@10001900 { + compatible = "brcm,bcm6328-leds"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x10001900 0x24>; + brcm,serial-leds; + + gphy0_spd0@0 { + reg = <0>; + brcm,hardware-controlled; + brcm,link-signal-sources = <0>; + }; + gphy0_spd1@1 { + reg = <1>; + brcm,hardware-controlled; + brcm,link-signal-sources = <1>; + }; + inet_red@2 { + reg = <2>; + active-low; + label = "red:inet"; + }; + dsl_green@3 { + reg = <3>; + active-low; + label = "green:dsl"; + }; + usb_green@4 { + reg = <4>; + active-low; + label = "green:usb"; + }; + wps_green@7 { + reg = <7>; + active-low; + label = "green:wps"; + }; + inet_green@8 { + reg = <8>; + active-low; + label = "green:inet"; + }; + ephy0_act@9 { + reg = <9>; + brcm,hardware-controlled; + }; + ephy1_act@10 { + reg = <10>; + brcm,hardware-controlled; + }; + ephy2_act@11 { + reg = <11>; + brcm,hardware-controlled; + }; + gphy0_act@12 { + reg = <12>; + brcm,hardware-controlled; + }; + ephy0_spd@13 { + reg = <13>; + brcm,hardware-controlled; + }; + ephy1_spd@14 { + reg = <14>; + brcm,hardware-controlled; + }; + ephy2_spd@15 { + reg = <15>; + brcm,hardware-controlled; + }; + power_green@20 { + reg = <20>; + active-low; + label = "green:power"; + default-state = "on"; + }; +}; + +example 3) BCM6362 with 1 LED for each EPHY + +leds0: led-controller@10001900 { + compatible = "brcm,bcm6328-leds"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x10001900 0x24>; + + usb@0 { + reg = <0>; + brcm,hardware-controlled; + brcm,link-signal-sources = <0>; + brcm,activity-signal-sources = <0>; + /* USB link/activity routed to USB LED */ + }; + inet@1 { + reg = <1>; + brcm,hardware-controlled; + brcm,activity-signal-sources = <1>; + /* INET activity routed to INET LED */ + }; + ephy0@4 { + reg = <4>; + brcm,hardware-controlled; + brcm,link-signal-sources = <4>; + /* EPHY0 link routed to EPHY0 LED */ + }; + ephy1@5 { + reg = <5>; + brcm,hardware-controlled; + brcm,link-signal-sources = <5>; + /* EPHY1 link routed to EPHY1 LED */ + }; + ephy2@6 { + reg = <6>; + brcm,hardware-controlled; + brcm,link-signal-sources = <6>; + /* EPHY2 link routed to EPHY2 LED */ + }; + ephy3@7 { + reg = <7>; + brcm,hardware-controlled; + brcm,link-signal-sources = <7>; + /* EPHY3 link routed to EPHY3 LED */ + }; + power_green@20 { + reg = <20>; + active-low; + label = "green:power"; + default-state = "on"; + }; +}; + +example 4) BCM6362 with 1 LED for all EPHYs + +leds0: led-controller@10001900 { + compatible = "brcm,bcm6328-leds"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x10001900 0x24>; + + usb@0 { + reg = <0>; + brcm,hardware-controlled; + brcm,link-signal-sources = <0 1>; + brcm,activity-signal-sources = <0 1>; + /* USB/INET link/activity routed to USB LED */ + }; + ephy@4 { + reg = <4>; + brcm,hardware-controlled; + brcm,link-signal-sources = <4 5 6 7>; + /* EPHY0/1/2/3 link routed to EPHY0 LED */ + }; + power_green@20 { + reg = <20>; + active-low; + label = "green:power"; + default-state = "on"; + }; +}; + +example 5) BCM6362 with EPHY LEDs swapped + +leds0: led-controller@10001900 { + compatible = "brcm,bcm6328-leds"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x10001900 0x24>; + + usb@0 { + reg = <0>; + brcm,hardware-controlled; + brcm,link-signal-sources = <0>; + brcm,activity-signal-sources = <0 1>; + /* USB link/activity & INET activity routed to USB LED */ + }; + ephy0@4 { + reg = <4>; + brcm,hardware-controlled; + brcm,link-signal-sources = <7>; + /* EPHY3 link routed to EPHY0 LED */ + }; + ephy1@5 { + reg = <5>; + brcm,hardware-controlled; + brcm,link-signal-sources = <6>; + /* EPHY2 link routed to EPHY1 LED */ + }; + ephy2@6 { + reg = <6>; + brcm,hardware-controlled; + brcm,link-signal-sources = <5>; + /* EPHY1 link routed to EPHY2 LED */ + }; + ephy3@7 { + reg = <7>; + brcm,hardware-controlled; + brcm,link-signal-sources = <4>; + /* EPHY0 link routed to EPHY3 LED */ + }; + power_green@20 { + reg = <20>; + active-low; + label = "green:power"; + default-state = "on"; + }; +}; -- 1.9.1 -- To unsubscribe from this list: send the line "unsubscribe linux-leds" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html
