I've read some old posts on this group, which give me some hope that I might
recover a failed drive. But I'm not well-versed in LVM, so details of what
I've read are going over my head.
My problems started when my laptop failed to shut down properly, and afterwards
booted only to dracut emergency shell. I've since attempted to rescue the bad
drive, using `ddrescue`. That tool reported 99.99% of the drive rescued, but
so far I'm unable to access the LVM data.
Decrypting the copy I made with `ddrescue` gives me
/dev/mapper/encrypted_rescue, but I can't activate the LVM data that is there.
I get these errors:
$ sudo lvconvert --repair qubes_dom0/pool00
WARNING: Not using lvmetad because of repair.
WARNING: Disabling lvmetad cache for repair command.
bad checksum in superblock, wanted 823063976
Repair of thin metadata volume of thin pool qubes_dom0/pool00 failed
(status:1). Manual repair required!
$ sudo thin_check /dev/mapper/encrypted_rescue
examining superblock
superblock is corrupt
bad checksum in superblock, wanted 636045691
(Note the two command return different "wanted" values. Are there two
superblocks?)
I found a post, several years old, written by Ming-Hung Tsai, which describes
restoring a broken superblock. I'll show that post below, along with my
questions, because I'm missing some of the knowledge necessary.
I would greatly appreciate any help!
-Dave
Original post from several years ago, plus my questions:
> The original post asks how to do if the superblock was broken (his superblock
> was accidentally wiped). Since that I don't have time to update the program
> at this moment, here's my workaround:
>
> 1. Partially rebuild the superblock
>
> (1) Obtain pool parameter from LVM
>
> ./sbin/lvm lvs vg1/tp1 -o transaction_id,chunksize,lv_size --units s
>
> sample output:
> Tran Chunk LSize
> 3545 128S 7999381504S
>
> The number of data blocks is $((7999381504/128)) = 62495168
>
Here's what I get:
$ sudo lvs qubes_dom0/pool00 -o transaction_id,chunksize,lv_size --units S
TransId Chunk LSize
14757 512S 901660672S
So, number of data blocks if I undestand correctly is $((901660672/512)) =
1761056
> (2) Create input.xml with pool parameters obtained from LVM:
>
> <superblock uuid="" time="0" transaction="3545"
> data_block_size="128" nr_data_blocks="62495168">
> </superblock>
>
> (3) Run thin_restore to generate a temporary metadata with correct superblock
>
> dd if=/dev/zero of=/tmp/test.bin bs=1M count=16
> thin_restore -i input.xml -o /tmp/test.bin
>
> The size of /tmp/test.bin depends on your pool size.
I don't understand the last sentence. What should the size of my /tmp/test.bin
be? Should I be using "bs=1M count=16"?
>
> (4) Copy the partially-rebuilt superblock (4KB) to your broken metadata.
> (<src_metadata>).
>
> dd if=/tmp/test.bin of=<src_metadata> bs=4k count=1 conv=notrunc
>
What is <src_metadata> here?
> 2. Run thin_ll_dump and thin_ll_restore
> https://www.redhat.com/archives/linux-lvm/2016-February/msg00038.html
>
> Example: assume that we found data-mapping-root=2303
> and device-details-root=277313
>
> ./pdata_tools thin_ll_dump <src_metadata> --data-mapping-root=2303 \
> --device-details-root 277313 -o thin_ll_dump.txt
>
> ./pdata_tools thin_ll_restore -E <src_metadata> -i thin_ll_dump.txt \
> -o <dst_metadata>
>
> Note that <dst_metadata> should be sufficient large especially when you
> have snapshots, since that the mapping trees reconstructed by thintools
> do not share blocks.
Here, I don't have commands `thin_ll_dump` or `thin_ll_restore`. How should I
obtain those? Or is there a way to do this with the tools I do have. (I'm on
fedora 30, FYI).
>
> 3. Fix superblock's time field
>
> (1) Run thin_dump on the repaired metadata
>
> thin_dump <dst_metadata> -o thin_dump.txt
>
> (2) Find the maximum time value in data mapping trees
> (the device with maximum snap_time might be remove, so find the
> maximum time in data mapping trees, not the device detail tree)
>
> grep "time=\"[0-9]*\"" thin_dump.txt -o | uniq | sort | uniq | tail
>
> (I run uniq twice to avoid sorting too much data)
>
> sample output:
> ...
> time="1785"
> time="1786"
> time="1787"
>
> so the maximum time is 1787.
>
> (3) Edit the "time" value of the <superblock> tag in thin_dump's output
>
> <superblock uuid="" time="1787" ... >
> ...
>
> (4) Run thin_restore to get the final metadata
>
> thin_restore -i thin_dump.txt -o <dst_metadata>
>
>
> Ming-Hung Tsai
_______________________________________________
linux-lvm mailing list
linux-lvm@redhat.com
https://www.redhat.com/mailman/listinfo/linux-lvm
read the LVM HOW-TO at http://tldp.org/HOWTO/LVM-HOWTO/
