On 09/03/17 21:45, Sakari Ailus wrote:
> Hi Hans,
>
> On Mon, Mar 06, 2017 at 03:56:06PM +0100, Hans Verkuil wrote:
>> From: Hans Verkuil <[email protected]>
>>
>> Add DT support. Use it to get the reset and pwdn pins (if there are any).
>> Tested with one sensor requiring reset/pwdn and one sensor that doesn't
>> have reset/pwdn pins.
>
> If I read the datasheet right, lifting the reset signal up will reset the
> sensor but the patch doesn't make use of that, it only ensures the reset
> signal stays low. Should you lift it up for a while as well? The datasheet
> doesn't say for how long that should be done, but that it should be usable
> after 1 ms since pulling reset down.
There does not seem to be any need for that. This sensor also comes in two
models: one with separate pwdn and reset pins, and one where it is just
hardwired.
If the hardwired variant doesn't need a reset pulse, then neither does the
variant with pins. It works, and I am not really willing to experiment with
this.
Regards,
Hans
>
>>
>> Signed-off-by: Hans Verkuil <[email protected]>
>> ---
>> drivers/media/i2c/ov7670.c | 40 ++++++++++++++++++++++++++++++++++++++--
>> 1 file changed, 38 insertions(+), 2 deletions(-)
>>
>> diff --git a/drivers/media/i2c/ov7670.c b/drivers/media/i2c/ov7670.c
>> index da0843617a49..f9d977430dcf 100644
>> --- a/drivers/media/i2c/ov7670.c
>> +++ b/drivers/media/i2c/ov7670.c
>> @@ -17,6 +17,8 @@
>> #include <linux/i2c.h>
>> #include <linux/delay.h>
>> #include <linux/videodev2.h>
>> +#include <linux/gpio.h>
>> +#include <linux/gpio/consumer.h>
>> #include <media/v4l2-device.h>
>> #include <media/v4l2-ctrls.h>
>> #include <media/v4l2-mediabus.h>
>> @@ -229,6 +231,8 @@ struct ov7670_info {
>> };
>> struct ov7670_format_struct *fmt; /* Current format */
>> struct clk *clk;
>> + struct gpio_desc *resetb_gpio;
>> + struct gpio_desc *pwdn_gpio;
>> int min_width; /* Filter out smaller sizes */
>> int min_height; /* Filter out smaller sizes */
>> int clock_speed; /* External clock speed (MHz) */
>> @@ -591,8 +595,6 @@ static int ov7670_init(struct v4l2_subdev *sd, u32 val)
>> return ov7670_write_array(sd, ov7670_default_regs);
>> }
>>
>> -
>> -
>> static int ov7670_detect(struct v4l2_subdev *sd)
>> {
>> unsigned char v;
>> @@ -1549,6 +1551,27 @@ static const struct ov7670_devtype ov7670_devdata[] =
>> {
>> },
>> };
>>
>> +static int ov7670_init_gpio(struct i2c_client *client, struct ov7670_info
>> *info)
>> +{
>> + info->pwdn_gpio = devm_gpiod_get_optional(&client->dev, "powerdown",
>> + GPIOD_OUT_LOW);
>> + if (IS_ERR(info->pwdn_gpio)) {
>> + dev_info(&client->dev, "can't get %s GPIO\n", "powerdown");
>> + return PTR_ERR(info->pwdn_gpio);
>> + }
>> +
>> + info->resetb_gpio = devm_gpiod_get_optional(&client->dev, "reset",
>> + GPIOD_OUT_LOW);
>> + if (IS_ERR(info->resetb_gpio)) {
>> + dev_info(&client->dev, "can't get %s GPIO\n", "reset");
>> + return PTR_ERR(info->resetb_gpio);
>> + }
>> +
>> + usleep_range(3000, 5000);
>> +
>> + return 0;
>> +}
>> +
>> static int ov7670_probe(struct i2c_client *client,
>> const struct i2c_device_id *id)
>> {
>> @@ -1594,6 +1617,10 @@ static int ov7670_probe(struct i2c_client *client,
>> return -EPROBE_DEFER;
>> clk_prepare_enable(info->clk);
>>
>> + ret = ov7670_init_gpio(client, info);
>> + if (ret)
>> + return ret;
>> +
>> info->clock_speed = clk_get_rate(info->clk) / 1000000;
>> if (info->clock_speed < 10 || info->clock_speed > 48)
>> return -EINVAL;
>> @@ -1689,9 +1716,18 @@ static const struct i2c_device_id ov7670_id[] = {
>> };
>> MODULE_DEVICE_TABLE(i2c, ov7670_id);
>>
>> +#if IS_ENABLED(CONFIG_OF)
>> +static const struct of_device_id ov7670_of_match[] = {
>> + { .compatible = "ovti,ov7670", },
>> + { /* sentinel */ },
>> +};
>> +MODULE_DEVICE_TABLE(of, ov7670_of_match);
>> +#endif
>> +
>> static struct i2c_driver ov7670_driver = {
>> .driver = {
>> .name = "ov7670",
>> + .of_match_table = of_match_ptr(ov7670_of_match),
>> },
>> .probe = ov7670_probe,
>> .remove = ov7670_remove,
>
