Hi Malathi,
On 11/13/18 9:28 AM, [email protected] wrote:
> On 2018-11-12 18:04, Stanimir Varbanov wrote:
>> Hi Tomasz,
>>
>> On 10/23/2018 05:50 AM, Tomasz Figa wrote:
>>> Hi Malathi,
>>>
>>> On Tue, Oct 9, 2018 at 4:58 PM Malathi Gottam
>>> <[email protected]> wrote:
>>>>
>>>> For lower resolutions, incase of encoder, the compressed
>>>> frame size is more than half of the corresponding input
>>>> YUV. Keep the size as same as YUV considering worst case.
>>>>
>>>> Signed-off-by: Malathi Gottam <[email protected]>
>>>> ---
>>>> drivers/media/platform/qcom/venus/helpers.c | 2 +-
>>>> 1 file changed, 1 insertion(+), 1 deletion(-)
>>>>
>>>> diff --git a/drivers/media/platform/qcom/venus/helpers.c
>>>> b/drivers/media/platform/qcom/venus/helpers.c
>>>> index 2679adb..05c5423 100644
>>>> --- a/drivers/media/platform/qcom/venus/helpers.c
>>>> +++ b/drivers/media/platform/qcom/venus/helpers.c
>>>> @@ -649,7 +649,7 @@ u32 venus_helper_get_framesz(u32 v4l2_fmt, u32
>>>> width, u32 height)
>>>> }
>>>>
>>>> if (compressed) {
>>>> - sz = ALIGN(height, 32) * ALIGN(width, 32) * 3 / 2 / 2;
>>>> + sz = ALIGN(height, 32) * ALIGN(width, 32) * 3 / 2;
>>>> return ALIGN(sz, SZ_4K);
>>>> }
>>>
>>> Note that the driver should not enforce one particular buffer size for
>>> bitstream buffers unless it's a workaround for broken firmware or
>>> hardware. The userspace should be able to select the desired size.
>>
>> Good point! Yes, we have to extend set_fmt to allow bigger sizeimage for
>> the compressed buffers (not only for encoder).
>
> So Stan you meant to say that we should allow s_fmt to accept client
> specified size?
yes but I do expect:
new_sizeimage = max(user_sizeimage, venus_helper_get_framesz)
and also user_sizeimage should be sanitized.
> If so should we set the inst->input_buf_size here in venc_s_fmt?
>
> @@ -333,10 +333,10 @@static const struct venus_format *
> venc_try_fmt_common(struct venus_inst *inst, struct v4l2_format *f)
>
> pixmp->num_planes = fmt->num_planes;
> pixmp->flags = 0;
> -
> - pfmt[0].sizeimage = venus_helper_get_framesz(pixmp->pixelformat,
> - pixmp->width,
> - pixmp->height);
> + if (!pfmt[0].sizeimage)
> + pfmt[0].sizeimage =
> venus_helper_get_framesz(pixmp->pixelformat,
> + pixmp->width,
> +
> pixmp->height);
yes, but please make
pfmt[0].sizeimage = max(pfmt[0].sizeimage, venus_helper_get_framesz)
and IMO this should be only for CAPTURE queue i.e. inst->output_buf_size
I'm still not sure do we need it for OUTPUT encoder queue.
>
> if (f->type == V4L2_BUF_TYPE_VIDEO_OUTPUT_MPLANE)
> pfmt[0].bytesperline = ALIGN(pixmp->width, 128);
> @@ -387,6 +387,7 @@ static int venc_s_fmt(struct file *file, void *fh,
> struct v4l2_format *f)
> venc_try_fmt_common(inst, &format);
>
> if (f->type == V4L2_BUF_TYPE_VIDEO_OUTPUT_MPLANE) {
> + inst->input_buf_size = pixmp->plane_fmt[0].sizeimage;
> inst->out_width = format.fmt.pix_mp.width;
> inst->out_height = format.fmt.pix_mp.height;
>
> Similar implementation is already handled in case of decoder.
>
> Then in queue setup, we can compare this against calculated size to
> obtain final buffer size
>
> @@ -899,7 +900,8 @@ static int venc_queue_setup(struct vb2_queue *q,
> sizes[0] = venus_helper_get_framesz(inst->fmt_out->pixfmt,
> inst->width,
> inst->height);
> - inst->input_buf_size = sizes[0];
> + if(inst->input_buf_size < sizes[0])
> + inst->input_buf_size = sizes[0];
> break;
>
> I hope this meets are requirements.
--
regards,
Stan
