On Sun, 29 Mar 2009, Hans Verkuil wrote: > On Sunday 29 March 2009 12:21:58 Trent Piepho wrote: > > On Sun, 29 Mar 2009, Hans Verkuil wrote: > > > On Sunday 29 March 2009 10:50:02 Patch from Trent Piepho wrote: > > > > From: Trent Piepho <xy...@speakeasy.org> > > > > v4l2-ioctl: Check format for S_PARM and G_PARM > > > > > > > > > > > > Return EINVAL if VIDIOC_S/G_PARM is called for a buffer type that the > > > > driver doesn't define a ->vidioc_try_fmt_XXX() method for. Several > > > > other ioctls, like QUERYBUF, QBUF, and DQBUF, etc. do this too. It > > > > saves each driver from having to check if the buffer type is one that > > > > it supports. > > > > > > Hi Trent, > > > > > > I wonder whether this change is correct. Looking at the spec I see that > > > g/s_parm only supports VIDEO_CAPTURE, VIDEO_OUTPUT and PRIVATE or up. > > > > > > So what should happen if the type is VIDEO_OVERLAY? I think the > > > g/s_parm implementation in v4l2-ioctl.c should first exclude the > > > unsupported types before calling check_fmt. > > > > This change doesn't actually enable g/s_parm for VIDEO_OVERLAY (or > > VBI_CAPTURE). It's the later bttv and saa7146 changes that do that. I > > considered this when I made those changes, as mentioned in those patch > > descriptions, but decided it was better to allow it. > > > > In those drivers g_parm only returns the frame rate, which seems just as > > valid for VIDEO_OVERLAY as it does for VIDEO_CAPTURE. Why should the > > driver not be allowed to return the frame rate for video overlay? Why > > should setting the overlay frame rate not be allowed? Those seems like > > perfectly reasonable operations to me. > > Not to me. VIDEO_OVERLAY just defines where the overlay is. But the actual > framerate is entirely dependent on the VIDEO_CAPTURE framerate. Just keep > to the spec for now. If a new driver appears that needs it then we can > always change it.
How does overlay depend on video capture in any way? It's perfectly reasonable for a driver to support _only_ overlay and not video capture. The zr36067 chip is only designed to support uncompressed data for video overlay for example. Allowing uncompressed video capture is a hack that the driver didn't have at one point. > > The spec doesn't explicitly say that only VIDEO_CAPTURE, VIDEO_OUTPUT and > > PRIVATE are supported. It says the "capture" field of the parm union is > > used when type is VIDEO_CAPTURE, the "output" field is used for > > VIDEO_OUTPUT, and "raw_data" is used for PRIVATE or higher. You're right > > in that it doesn't say what you're supposed to use for VIDEO_OVERLAY, > > VBI_CAPTURE or any other buffer types. But it doesn't say they're not > > allowed either. IMHO, it's likely the spec authors' intent wasn't to not > > allow g_parm with VIDEO_OVERLAY, but rather that they just didn't think > > of that case. > > No, I agree with the spec in that I see no use case for it. Should there be > one, then I'd like to see that in an actual driver implementation and in > that case the spec should be adjusted as well. How about getting the frame rate of video overlay? Works with bttv. > In addition, g/s_parm is only used in combination with webcams/sensors for > which overlays and vbi are irrelevant. There are several drivers for non-webcams, like bttv, saa7134, and saa7146, that support g_parm. Why is returning the frame rate for video capture not valid? Why does the number of buffers used for read() mode only make sense for webcams? > > Thinking about it now, I think what makes the most sense is to use > > "capture" for VIDEO_OVERLAY, VBI_CAPTURE, and SLICED_VBI_CAPTURE. And > > use "output" for VBI_OUTPUT, SLICED_VBI_OUTPUT and VIDEO_OUTPUT_OVERLAY. > > > > > I also wonder whether check_fmt shouldn't check for the presence of the > > > s_fmt callbacks instead of try_fmt since try_fmt is an optional ioctl. > > > > I noticed that too. saa7146 doesn't have a try_fmt call for vbi_capture > > but is apparently supposed to support it. I sent a message about that > > earlier. > > I saw that. So why not check for s_fmt instead of try_fmt? That would solve > this potential problem. Because that's clearly a change that belongs in another patch. -- To unsubscribe from this list: send the line "unsubscribe linux-media" in the body of a message to majord...@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
