On Tue, Sep 1, 2009 at 9:37 PM, Dmitri Belimov<d.beli...@gmail.com> wrote:
> Hi All
>
> Add FM radio for the xc5000 silicon tuner chip.
>
> diff -r 28f8b0ebd224 linux/drivers/media/common/tuners/xc5000.c
> --- a/linux/drivers/media/common/tuners/xc5000.c Sun Aug 23 13:55:25
> 2009 -0300
> +++ b/linux/drivers/media/common/tuners/xc5000.c Wed Sep 02 06:32:12
> 2009 +1000
> @@ -747,14 +747,11 @@
> return ret;
> }
>
> -static int xc5000_set_analog_params(struct dvb_frontend *fe,
> +static int xc5000_set_tv_freq(struct dvb_frontend *fe,
> struct analog_parameters *params)
> {
> struct xc5000_priv *priv = fe->tuner_priv;
> int ret;
> -
> - if (xc5000_is_firmware_loaded(fe) != XC_RESULT_SUCCESS)
> - xc_load_fw_and_init_tuner(fe);
>
> dprintk(1, "%s() frequency=%d (in units of 62.5khz)\n",
> __func__, params->frequency);
> @@ -834,6 +831,67 @@
>
> return 0;
> }
> +
> +static int xc5000_set_radio_freq(struct dvb_frontend *fe,
> + struct analog_parameters *params)
> +{
> + struct xc5000_priv *priv = fe->tuner_priv;
> + int ret = -EINVAL;
> +
> + dprintk(1, "%s() frequency=%d (in units of khz)\n",
> + __func__, params->frequency);
> +
> + priv->freq_hz = params->frequency * 125 / 2;
> +
> + priv->rf_mode = XC_RF_MODE_AIR;
> +
> + ret = xc_SetTVStandard(priv,
> + XC5000_Standard[FM_Radio_INPUT1].VideoMode,
> + XC5000_Standard[FM_Radio_INPUT1].AudioMode);
> +
> + if (ret != XC_RESULT_SUCCESS) {
> + printk(KERN_ERR "xc5000: xc_SetTVStandard failed\n");
> + return -EREMOTEIO;
> + }
> +
> + ret = xc_SetSignalSource(priv, priv->rf_mode);
> + if (ret != XC_RESULT_SUCCESS) {
> + printk(KERN_ERR
> + "xc5000: xc_SetSignalSource(%d) failed\n",
> + priv->rf_mode);
> + return -EREMOTEIO;
> + }
> +
> + xc_tune_channel(priv, priv->freq_hz, XC_TUNE_ANALOG);
> +
> + return 0;
> +}
> +
> +static int xc5000_set_analog_params(struct dvb_frontend *fe,
> + struct analog_parameters *params)
> +{
> + struct xc5000_priv *priv = fe->tuner_priv;
> + int ret = -EINVAL;
> +
> + if (priv->i2c_props.adap == NULL)
> + return -EINVAL;
> +
> + if (xc5000_is_firmware_loaded(fe) != XC_RESULT_SUCCESS)
> + xc_load_fw_and_init_tuner(fe);
> +
> + switch (params->mode) {
> + case V4L2_TUNER_RADIO:
> + ret = xc5000_set_radio_freq(fe, params);
> + break;
> + case V4L2_TUNER_ANALOG_TV:
> + case V4L2_TUNER_DIGITAL_TV:
> + ret = xc5000_set_tv_freq(fe, params);
> + break;
> + }
> +
> + return ret;
> +}
> +
>
> static int xc5000_get_frequency(struct dvb_frontend *fe, u32 *freq)
> {
>
> Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <d.beli...@gmail.com>
>
> With my best regards, Dmitry.
Hello Dmitri,
A few comments;
I don't think the code should have FM1 hard-coded as the only valid
input. You should probably add a parameter to the xc500_config struct
to specify which FM input to use (so the person defining the board
profile can define which input is appropriate).
Does the signal lock register actually work for FM? I assume it does,
but I'm not sure.
Also, I would probably have him move the setting of priv->rf_mode
further down in the function. That way it the xc5000_priv struct
won't get out of sync with the actual state of the device if the call
to xc_SetTVStandard() fails.
Other than those two things though it looks ok at first glance.
Devin
--
Devin J. Heitmueller - Kernel Labs
http://www.kernellabs.com
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
