Am 15.11.2010 22:00, schrieb Massis Sirapian:
Le 15/11/2010 18:43, Stefan Ringel a écrit :
Am 15.11.2010 10:15, schrieb Richard Zidlicky:
On Sun, Nov 14, 2010 at 08:22:44PM +0100, Massis Sirapian wrote:

Thanks Stefan. I've checked the /drivers/media/IR/keymaps of the kernel
source directory, but nothing seems to fit my remote, which is a
DSR-0012 : http://lirc.sourceforge.net/remotes/hauppauge/DSR-0112.jpg.
FYI, this remote is identical to that shipped with (most?) Haupauge
Ministicks
and the codes reportedly match the rc-dib0700-rc5.c keymap. However I
have not figured
out how to make the userspace work with the new ir-code yet.

Richard
With my terratec cinergy hybrid xe (equal yours hvr900h) I have this:

localhost:/usr/src/src/tm6000_alsa/utils/v4l-utils # ir-keytable
Found /sys/class/rc/rc0/ (/dev/input/event5) with:
Driver tm6000, table rc-nec-terratec-cinergy-xs
Supported protocols: NEC RC-5 Enabled protocols: NEC

I can change outside the keytable.


Just loading tm6000-dvb, I have this :
[  253.829422] IR NEC protocol handler initialized
[  253.846608] IR RC5(x) protocol handler initialized
[ 253.883882] tm6000: module is from the staging directory, the quality is unknown, you have been warned.
[  253.886611] tm6000 v4l2 driver version 0.0.2 loaded
[  253.887558] tm6000: alt 0, interface 0, class 255
[  253.887574] tm6000: alt 0, interface 0, class 255
[  253.887575] tm6000: Bulk IN endpoint: 0x82 (max size=512 bytes)
[  253.887577] tm6000: alt 0, interface 0, class 255
[  253.887578] tm6000: alt 1, interface 0, class 255
[  253.887579] tm6000: ISOC IN endpoint: 0x81 (max size=3072 bytes)
[  253.887580] tm6000: alt 1, interface 0, class 255
[  253.887581] tm6000: alt 1, interface 0, class 255
[  253.887582] tm6000: INT IN endpoint: 0x83 (max size=4 bytes)
[  253.887583] tm6000: alt 2, interface 0, class 255
[  253.887584] tm6000: alt 2, interface 0, class 255
[  253.887586] tm6000: alt 2, interface 0, class 255
[  253.887587] tm6000: alt 3, interface 0, class 255
[  253.887588] tm6000: alt 3, interface 0, class 255
[  253.887589] tm6000: alt 3, interface 0, class 255
[  253.887590] tm6000: New video device @ 480 Mbps (2040:6600, ifnum 0)
[  253.887591] tm6000: Found Hauppauge WinTV HVR-900H / WinTV USB2-Stick
[  253.888848] IR RC6 protocol handler initialized
[  253.890209] IR JVC protocol handler initialized
[  253.891515] IR Sony protocol handler initialized
[  253.893815] lirc_dev: IR Remote Control driver registered, major 250
[  253.894722] IR LIRC bridge handler initialized
[  254.806122] Board version = 0x67980bf4
[  255.197098] board=0x67980bf4
[ 255.320786] tm6000 #0: i2c eeprom 00: 01 59 54 45 12 01 00 02 00 00 00 40 40 20 00 66 .YTE.......@@ .f [ 255.512277] tm6000 #0: i2c eeprom 10: 69 00 10 20 40 01 02 03 48 00 79 00 62 00 72 00 i.. @...H.y.b.r. [ 255.703783] tm6000 #0: i2c eeprom 20: ff 00 64 ff ff ff ff ff ff ff ff ff ff ff ff ff ..d............. [ 255.895281] tm6000 #0: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................ [ 256.086786] tm6000 #0: i2c eeprom 40: 10 03 48 00 56 00 52 00 39 00 30 00 30 00 48 00 ..H.V.R.9.0.0.H. [ 256.278289] tm6000 #0: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................ [ 256.469783] tm6000 #0: i2c eeprom 60: 30 ff ff ff 0f ff ff ff ff ff 0a 03 32 00 2e 00 0...........2... [ 256.661287] tm6000 #0: i2c eeprom 70: 3f 00 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ?............... [ 256.852786] tm6000 #0: i2c eeprom 80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................ [ 257.044307] tm6000 #0: i2c eeprom 90: 30 ff ff ff 16 03 34 00 30 00 33 00 32 00 32 00 0.....4.0.3.2.2. [ 257.235798] tm6000 #0: i2c eeprom a0: 33 00 36 00 39 00 30 00 35 00 00 00 77 00 ff ff 3.6.9.0.5...w... [ 257.427295] tm6000 #0: i2c eeprom b0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................ [ 257.618794] tm6000 #0: i2c eeprom c0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................ [ 257.810303] tm6000 #0: i2c eeprom d0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................ [ 258.001810] tm6000 #0: i2c eeprom e0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................ [ 258.193291] tm6000 #0: i2c eeprom f0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................
[  258.372825]   ................
[  258.378849] tuner 4-0061: chip found @ 0xc2 (tm6000 #0)
[  258.400777] xc2028 4-0061: creating new instance
[  258.400779] xc2028 4-0061: type set to XCeive xc2028/xc3028 tuner
[  258.400781] Setting firmware parameters for xc2028
[ 258.427221] xc2028 4-0061: Loading 81 firmware images from xc3028L-v36.fw, type: xc2028 firmware, ver 3.6 [ 258.668063] xc2028 4-0061: Loading firmware for type=BASE (1), id 0000000000000000. [ 333.245767] xc2028 4-0061: Loading firmware for type=(0), id 000000000000b700.
[  334.510473] SCODE (20000000), id 000000000000b700:
[ 334.510476] xc2028 4-0061: Loading SCODE for type=MONO SCODE HAS_IF_4320 (60008000), id 0000000000008000. [ 335.783252] Trident TVMaster TM5600/TM6000/TM6010 USB2 board (Load status: 0)
[  335.783271] usbcore: registered new interface driver tm6000
[  335.784191] tm6000: open called (dev=video1)
[ 335.815994] tm6000_dvb: module is from the staging directory, the quality is unknown, you have been warned.
[  335.854973] DVB: registering new adapter (Trident TVMaster 6000 DVB-T)
[ 335.854976] DVB: registering adapter 0 frontend 0 (Zarlink ZL10353 DVB-T)...
[  335.855087] xc2028 4-0061: attaching existing instance
[  335.855088] xc2028 4-0061: type set to XCeive xc2028/xc3028 tuner
[  335.855090] tm6000: XC2028/3028 asked to be attached to frontend!
[  335.855343] tm6000 #0: Initialized (TM6000 dvb Extension) extension
[  337.338951] tm6000: open called (dev=video1)

Then, ir-keytable complains : "Couldn't find any node at /sys/class/rc/rc*."

So it looks Jarod is right : tm6000 is loading, it calls lirc_dev and a bunch of protocol modules, but the IR doesn't seem to be handled.

I saw some ir lines in tm6000-cards.c for the HVR900H and thought the IR receiver was supported. It's a bit disturbing if the cinergy stick you evoke is equivalent to HVR900H and works, while HVR900H's IR part isn't implemented ?

Massis


--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majord...@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
add this line with the right map name

.ir_codes = RC_MAP_NEC_TERRATEC_CINERGY_XS,

in this struct

[TM6010_BOARD_HAUPPAUGE_900H] = {
.name = "Hauppauge WinTV HVR-900H / WinTV USB2-Stick",
                 .tuner_type   = TUNER_XC2028, /* has a XC3028 */
                 .tuner_addr   = 0xc2 >> 1,
                 .demod_addr   = 0x1e >> 1,
                 .type         = TM6010,
                 .caps = {
                         .has_tuner    = 1,
                         .has_dvb      = 1,
                         .has_zl10353  = 1,
                         .has_eeprom   = 1,
                         .has_remote   = 1,
                 },
                 .gpio = {
                         .tuner_reset    = TM6010_GPIO_2,
                         .tuner_on       = TM6010_GPIO_3,
                         .demod_reset    = TM6010_GPIO_1,
                         .demod_on       = TM6010_GPIO_4,
                         .power_led      = TM6010_GPIO_7,
                         .dvb_led        = TM6010_GPIO_5,
                         .ir             = TM6010_GPIO_0,
                 },

Stefan
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majord...@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Reply via email to