With this patch I try again to add initial support for HVR930C.
Tested only DVB-T, since in Italy Analog service is stopped.
Actually "scan -a0 -f1", find only about 50 channel while 400 should
be available.
Signed-off-by: Eddi De Pieri <e...@depieri.net>
Regards
Eddi
diff -u -N -r linux/drivers/media/common/tuners/xc5000.c linux.patched/drivers/media/common/tuners/xc5000.c
--- linux/drivers/media/common/tuners/xc5000.c 2011-03-31 23:56:49.000000000 +0200
+++ linux.patched/drivers/media/common/tuners/xc5000.c 2011-11-19 15:37:20.516138695 +0100
@@ -977,6 +977,13 @@
return 0;
}
+static int xc5000_get_if_frequency(struct dvb_frontend *fe, u32 *frequency)
+{
+ struct xc5000_priv *priv = fe->tuner_priv;
+ *frequency = priv->if_khz * 1000;
+ return 0;
+}
+
static int xc5000_get_status(struct dvb_frontend *fe, u32 *status)
{
struct xc5000_priv *priv = fe->tuner_priv;
@@ -996,6 +1003,8 @@
struct xc5000_priv *priv = fe->tuner_priv;
int ret = 0;
+ mutex_lock(&xc5000_list_mutex);
+
if (xc5000_is_firmware_loaded(fe) != XC_RESULT_SUCCESS) {
ret = xc5000_fwupload(fe);
if (ret != XC_RESULT_SUCCESS)
@@ -1015,6 +1024,8 @@
/* Default to "CABLE" mode */
ret |= xc_write_reg(priv, XREG_SIGNALSOURCE, XC_RF_MODE_CABLE);
+ mutex_unlock(&xc5000_list_mutex);
+
return ret;
}
@@ -1109,6 +1120,7 @@
.set_analog_params = xc5000_set_analog_params,
.get_frequency = xc5000_get_frequency,
.get_bandwidth = xc5000_get_bandwidth,
+ .get_if_frequency = xc5000_get_if_frequency,
.get_status = xc5000_get_status
};
diff -u -N -r linux/drivers/media/dvb/frontends/drxk.h linux.patched/drivers/media/dvb/frontends/drxk.h
--- linux/drivers/media/dvb/frontends/drxk.h 2011-07-11 20:09:53.000000000 +0200
+++ linux.patched/drivers/media/dvb/frontends/drxk.h 2011-11-19 15:20:32.119137206 +0100
@@ -25,6 +25,8 @@
bool antenna_dvbt;
u16 antenna_gpio;
+
+ int chunk_size;
const char *microcode_name;
};
diff -u -N -r linux/drivers/media/dvb/frontends/drxk_hard.c linux.patched/drivers/media/dvb/frontends/drxk_hard.c
--- linux/drivers/media/dvb/frontends/drxk_hard.c 2011-09-04 05:45:09.000000000 +0200
+++ linux.patched/drivers/media/dvb/frontends/drxk_hard.c 2011-11-19 15:20:32.123137210 +0100
@@ -681,7 +681,8 @@
state->m_hasOOB = false;
state->m_hasAudio = false;
- state->m_ChunkSize = 124;
+ if (!state->m_ChunkSize)
+ state->m_ChunkSize = 124;
state->m_oscClockFreq = 0;
state->m_smartAntInverted = false;
@@ -6423,6 +6424,7 @@
state->no_i2c_bridge = config->no_i2c_bridge;
state->antenna_gpio = config->antenna_gpio;
state->antenna_dvbt = config->antenna_dvbt;
+ state->m_ChunkSize = config->chunk_size;
/* NOTE: as more UIO bits will be used, add them to the mask */
state->UIO_mask = config->antenna_gpio;
diff -u -N -r linux/drivers/media/video/em28xx/em28xx-cards.c linux.patched/drivers/media/video/em28xx/em28xx-cards.c
--- linux/drivers/media/video/em28xx/em28xx-cards.c 2011-11-04 05:45:40.000000000 +0100
+++ linux.patched/drivers/media/video/em28xx/em28xx-cards.c 2011-11-19 15:21:18.247365922 +0100
@@ -336,6 +336,24 @@
{ -1, -1, -1, -1},
};
+static struct em28xx_reg_seq hauppauge_930c_gpio[] = {
+// xc5000 reset
+ {EM2874_R80_GPIO, 0x6f, 0xff, 10},
+ {EM2874_R80_GPIO, 0x4f, 0xff, 10},
+ {EM2874_R80_GPIO, 0x6f, 0xff, 10},
+ {EM2874_R80_GPIO, 0x4f, 0xff, 10},
+ { -1, -1, -1, -1},
+};
+
+#if 0
+static struct em28xx_reg_seq hauppauge_930c_digital[] = {
+ {EM2874_R80_GPIO, 0xf6, 0xff, 10},
+ {EM2874_R80_GPIO, 0xe6, 0xff, 100},
+ {EM2874_R80_GPIO, 0xa6, 0xff, 10},
+ { -1, -1, -1, -1},
+};
+#endif
+
/*
* Board definitions
*/
@@ -892,6 +910,19 @@
EM28XX_I2C_CLK_WAIT_ENABLE |
EM28XX_I2C_FREQ_400_KHZ,
},
+ [EM2884_BOARD_HAUPPAUGE_WINTV_HVR_930C] = {
+ .name = "Hauppauge WinTV HVR 930C",
+ .has_dvb = 1,
+//#if 0
+// .tuner_type = TUNER_XC5000,
+// .tuner_addr = 0x41,
+// .dvb_gpio = hauppauge_930c_digital, /* FIXME: probably wrong */
+ .tuner_gpio = hauppauge_930c_gpio,
+//#endif
+ .i2c_speed = EM2874_I2C_SECONDARY_BUS_SELECT |
+ EM28XX_I2C_CLK_WAIT_ENABLE |
+ EM28XX_I2C_FREQ_400_KHZ,
+ },
[EM2880_BOARD_HAUPPAUGE_WINTV_HVR_900] = {
.name = "Hauppauge WinTV HVR 900",
.tda9887_conf = TDA9887_PRESENT,
@@ -1975,6 +2006,8 @@
.driver_info = EM28174_BOARD_PCTV_290E },
{ USB_DEVICE(0x2013, 0x024c),
.driver_info = EM28174_BOARD_PCTV_460E },
+ { USB_DEVICE(0x2040, 0x1605),
+ .driver_info = EM2884_BOARD_HAUPPAUGE_WINTV_HVR_930C },
{ },
};
MODULE_DEVICE_TABLE(usb, em28xx_id_table);
@@ -2028,10 +2061,10 @@
int rc = 0;
struct em28xx *dev = ptr;
- if (dev->tuner_type != TUNER_XC2028)
+ if (dev->tuner_type != TUNER_XC2028 && dev->tuner_type != TUNER_XC5000)
return 0;
- if (command != XC2028_TUNER_RESET)
+ if (command != XC2028_TUNER_RESET && command != XC5000_TUNER_RESET)
return 0;
rc = em28xx_gpio_set(dev, dev->board.tuner_gpio);
diff -u -N -r linux/drivers/media/video/em28xx/em28xx-dvb.c linux.patched/drivers/media/video/em28xx/em28xx-dvb.c
--- linux/drivers/media/video/em28xx/em28xx-dvb.c 2011-09-22 05:45:23.000000000 +0200
+++ linux.patched/drivers/media/video/em28xx/em28xx-dvb.c 2011-11-19 15:20:32.127137205 +0100
@@ -1,4 +1,4 @@
-/*
+/*6
DVB device driver for em28xx
(c) 2008-2011 Mauro Carvalho Chehab <mche...@infradead.org>
@@ -316,6 +316,14 @@
.microcode_name = "dvb-usb-terratec-h5-drxk.fw",
};
+struct drxk_config hauppauge_930c_drxk = {
+ .adr = 0x29,
+ .single_master = 1,
+ .no_i2c_bridge = 1,
+ .microcode_name = "dvb-usb-hauppauge-hvr930c-drxk.fw",
+ .chunk_size = 56,
+};
+
static int drxk_gate_ctrl(struct dvb_frontend *fe, int enable)
{
struct em28xx_dvb *dvb = fe->sec_priv;
@@ -334,6 +342,91 @@
return status;
}
+static void hauppauge_hvr930c_init(struct em28xx *dev)
+{
+ int i;
+
+
+ struct em28xx_reg_seq hauppauge_hvr930c_init[] = {
+ {EM2874_R80_GPIO, 0xff, 0xff, 101}, //11111111
+// {0xd , 0xff, 0xff, 101}, //11111111
+ {EM2874_R80_GPIO, 0xfb, 0xff, 50}, //11111011 init bit 3
+ {EM2874_R80_GPIO, 0xff, 0xff, 184}, //11111111
+ { -1, -1, -1, -1},
+ };
+ struct em28xx_reg_seq hauppauge_hvr930c_end[] = {
+ {EM2874_R80_GPIO, 0xef, 0xff, 1}, //11101111
+ {EM2874_R80_GPIO, 0xaf, 0xff, 101}, //10101111 init bit 7
+ {EM2874_R80_GPIO, 0xef, 0xff, 118}, //11101111
+
+
+//per il tuner?
+ {EM2874_R80_GPIO, 0xef, 0xff, 1}, //11101111
+ {EM2874_R80_GPIO, 0xcf, 0xff, 11}, //11001111 init bit 6
+ {EM2874_R80_GPIO, 0xef, 0xff, 64}, //11101111
+
+ {EM2874_R80_GPIO, 0xcf, 0xff, 101}, //11001111 init bit 6
+ {EM2874_R80_GPIO, 0xef, 0xff, 101}, //11101111
+ {EM2874_R80_GPIO, 0xcf, 0xff, 11}, //11001111 init bit 6
+ {EM2874_R80_GPIO, 0xef, 0xff, 101}, //11101111
+
+// {EM2874_R80_GPIO, 0x6f, 0xff, 10}, //01101111
+// {EM2874_R80_GPIO, 0x6d, 0xff, 100}, //01101101 init bit 2
+ { -1, -1, -1, -1},
+ };
+
+ struct em28xx_reg_seq hauppauge_hvr930c_end2[] = {
+// {EM2874_R80_GPIO, 0x6f, 0xff, 124}, //01101111
+// {EM2874_R80_GPIO, 0x4f, 0xff, 11}, //01001111 init bit 6
+// {EM2874_R80_GPIO, 0x6f, 0xff, 1}, //01101111
+// {EM2874_R80_GPIO, 0x4f, 0xff, 10}, //01001111 init bit 6
+// {EM2874_R80_GPIO, 0x6f, 0xff, 100}, //01101111
+// {0xd , 0x42, 0xff, 101}, //11111111
+ { -1, -1, -1, -1},
+ };
+ struct {
+ unsigned char r[4];
+ int len;
+ } regs[] = {
+ {{ 0x06, 0x02, 0x00, 0x31 }, 4},
+ {{ 0x01, 0x02 }, 2},
+ {{ 0x01, 0x02, 0x00, 0xc6 }, 4},
+ {{ 0x01, 0x00 }, 2},
+ {{ 0x01, 0x00, 0xff, 0xaf }, 4},
+ {{ 0x01, 0x00, 0x03, 0xa0 }, 4},
+ {{ 0x01, 0x00 }, 2},
+ {{ 0x01, 0x00, 0x73, 0xaf }, 4},
+ {{ 0x04, 0x00 }, 2},
+ {{ 0x00, 0x04 }, 2},
+ {{ 0x00, 0x04, 0x00, 0x0a }, 4},
+ {{ 0x04, 0x14 }, 2},
+ {{ 0x04, 0x14, 0x00, 0x00 }, 4},
+ };
+
+ em28xx_gpio_set(dev, hauppauge_hvr930c_init);
+ em28xx_write_reg(dev, EM28XX_R06_I2C_CLK, 0x40);
+ msleep(10);
+ em28xx_write_reg(dev, EM28XX_R06_I2C_CLK, 0x44);
+ msleep(10);
+
+ dev->i2c_client.addr = 0x82 >> 1;
+
+ for (i = 0; i < ARRAY_SIZE(regs); i++)
+ i2c_master_send(&dev->i2c_client, regs[i].r, regs[i].len);
+ em28xx_gpio_set(dev, hauppauge_hvr930c_end);
+
+ msleep(100);
+
+ em28xx_write_reg(dev, EM28XX_R06_I2C_CLK, 0x44);
+ msleep(30);
+
+ em28xx_gpio_set(dev, hauppauge_hvr930c_end2);
+ msleep(10);
+ em28xx_write_reg(dev, EM28XX_R06_I2C_CLK, 0x45);
+ msleep(10);
+
+}
+
static void terratec_h5_init(struct em28xx *dev)
{
int i;
@@ -788,6 +881,47 @@
mfe_shared = 1;
}
break;
+ case EM2884_BOARD_HAUPPAUGE_WINTV_HVR_930C:
+ hauppauge_hvr930c_init(dev);
+
+ dvb->dont_attach_fe1 = 1;
+
+ dvb->fe[0] = dvb_attach(drxk_attach, &hauppauge_930c_drxk, &dev->i2c_adap, &dvb->fe[1]);
+ if (!dvb->fe[0]) {
+ result = -EINVAL;
+ goto out_free;
+ }
+ /* FIXME: do we need a pll semaphore? */
+ dvb->fe[0]->sec_priv = dvb;
+ sema_init(&dvb->pll_mutex, 1);
+ dvb->gate_ctrl = dvb->fe[0]->ops.i2c_gate_ctrl;
+ dvb->fe[0]->ops.i2c_gate_ctrl = drxk_gate_ctrl;
+ dvb->fe[1]->id = 1;
+
+ /* Attach xc5000 */
+ struct xc5000_config cfg;
+ memset(&cfg, 0, sizeof(cfg));
+ cfg.i2c_address = 0x61;
+ //cfg.if_khz = 4570; //FIXME
+ cfg.if_khz = 4000; //FIXME (should be ok) read from i2c traffic
+
+ if (dvb->fe[0]->ops.i2c_gate_ctrl)
+ dvb->fe[0]->ops.i2c_gate_ctrl(dvb->fe[0], 1);
+ if (!dvb_attach(xc5000_attach, dvb->fe[0], &dev->i2c_adap, &cfg)) {
+ result = -EINVAL;
+ goto out_free;
+ }
+
+ if (dvb->fe[0]->ops.i2c_gate_ctrl)
+ dvb->fe[0]->ops.i2c_gate_ctrl(dvb->fe[0], 0);
+
+ /* Hack - needed by drxk/tda18271c2dd */
+ dvb->fe[1]->tuner_priv = dvb->fe[0]->tuner_priv;
+ memcpy(&dvb->fe[1]->ops.tuner_ops,
+ &dvb->fe[0]->ops.tuner_ops,
+ sizeof(dvb->fe[0]->ops.tuner_ops));
+
+ break;
case EM2884_BOARD_TERRATEC_H5:
terratec_h5_init(dev);
@@ -798,7 +932,6 @@
result = -EINVAL;
goto out_free;
}
-
/* FIXME: do we need a pll semaphore? */
dvb->fe[0]->sec_priv = dvb;
sema_init(&dvb->pll_mutex, 1);
@@ -845,7 +978,9 @@
}
/* define general-purpose callback pointer */
dvb->fe[0]->callback = em28xx_tuner_callback;
-
+ if (dvb->fe[1])
+ dvb->fe[1]->callback = em28xx_tuner_callback;
+
/* register everything */
result = em28xx_register_dvb(dvb, THIS_MODULE, dev, &dev->udev->dev);
diff -u -N -r linux/drivers/media/video/em28xx/em28xx.h linux.patched/drivers/media/video/em28xx/em28xx.h
--- linux/drivers/media/video/em28xx/em28xx.h 2011-09-27 05:45:21.000000000 +0200
+++ linux.patched/drivers/media/video/em28xx/em28xx.h 2011-11-19 15:21:47.199509466 +0100
@@ -38,6 +38,7 @@
#include <media/videobuf-dvb.h>
#endif
#include "tuner-xc2028.h"
+#include "xc5000.h"
#include "em28xx-reg.h"
/* Boards supported by driver */
@@ -121,6 +122,7 @@
#define EM28174_BOARD_PCTV_290E 78
#define EM2884_BOARD_TERRATEC_H5 79
#define EM28174_BOARD_PCTV_460E 80
+#define EM2884_BOARD_HAUPPAUGE_WINTV_HVR_930C 81
/* Limits minimum and default number of buffers */
#define EM28XX_MIN_BUF 4
