> -----Original Message-----
> From: [email protected] [mailto:linux-omap-
> [email protected]] On Behalf Of Aguirre, Sergio
> Sent: Thursday, December 01, 2011 5:45 AM
> To: [email protected]
> Cc: [email protected]; [email protected];
> [email protected]; Aguirre, Sergio
> Subject: [PATCH v2 10/11] arm: omap4panda: Add support for omap4iss camera
>
> This adds support for camera interface with the support for
> following sensors:
>
> - OV5640
> - OV5650
>
> Signed-off-by: Sergio Aguirre <[email protected]>
> ---
> arch/arm/mach-omap2/Kconfig | 27 ++++
> arch/arm/mach-omap2/Makefile | 1 +
> arch/arm/mach-omap2/board-omap4panda-camera.c | 198
> +++++++++++++++++++++++++
> 3 files changed, 226 insertions(+), 0 deletions(-)
> create mode 100644 arch/arm/mach-omap2/board-omap4panda-camera.c
>
> diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach-omap2/Kconfig
> index f883abb..0fc5ce9 100644
> --- a/arch/arm/mach-omap2/Kconfig
> +++ b/arch/arm/mach-omap2/Kconfig
> @@ -358,6 +358,33 @@ config MACH_OMAP4_PANDA
> select OMAP_PACKAGE_CBS
> select REGULATOR_FIXED_VOLTAGE
>
> +config MACH_OMAP4_PANDA_CAMERA_SUPPORT
> + bool "OMAP4 Panda Board Camera support"
> + depends on MACH_OMAP4_PANDA
> + select MEDIA_SUPPORT
> + select MEDIA_CONTROLLER
> + select VIDEO_DEV
> + select VIDEO_V4L2_SUBDEV_API
> + select VIDEO_OMAP4
> + help
> + Enable Camera HW support for PandaBoard.
> + This is for using the OMAP4 ISS CSI2A Camera sensor
> + interface.
> +
> +choice
> + prompt "Camera sensor to use"
> + depends on MACH_OMAP4_PANDA_CAMERA_SUPPORT
> + default MACH_OMAP4_PANDA_CAM_OV5650
> +
> + config MACH_OMAP4_PANDA_CAM_OV5640
> + bool "Use OmniVision OV5640 Camera"
> + select VIDEO_OV5640
> +
> + config MACH_OMAP4_PANDA_CAM_OV5650
> + bool "Use OmniVision OV5650 Camera"
> + select VIDEO_OV5650
> +endchoice
> +
> config OMAP3_EMU
> bool "OMAP3 debugging peripherals"
> depends on ARCH_OMAP3
> diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile
> index 8bc446a..e80724d 100644
> --- a/arch/arm/mach-omap2/Makefile
> +++ b/arch/arm/mach-omap2/Makefile
> @@ -236,6 +236,7 @@ obj-$(CONFIG_MACH_TI8168EVM) += board-
> ti8168evm.o
> # Platform specific device init code
>
> obj-$(CONFIG_MACH_OMAP_4430SDP_CAMERA_SUPPORT) +=
> board-4430sdp-camera.o
> +obj-$(CONFIG_MACH_OMAP4_PANDA_CAMERA_SUPPORT) += board-omap4panda-
> camera.o
>
Can't this be merged into single file? Do we really need separate file for
every board here?
I am sure you would have thought about this.
> omap-flash-$(CONFIG_MTD_NAND_OMAP2) := board-flash.o
> omap-flash-$(CONFIG_MTD_ONENAND_OMAP2) := board-flash.o
> diff --git a/arch/arm/mach-omap2/board-omap4panda-camera.c
> b/arch/arm/mach-omap2/board-omap4panda-camera.c
> new file mode 100644
> index 0000000..02ef36e
> --- /dev/null
> +++ b/arch/arm/mach-omap2/board-omap4panda-camera.c
> @@ -0,0 +1,198 @@
> +#include <linux/gpio.h>
> +#include <linux/clk.h>
> +#include <linux/delay.h>
> +
> +#include <plat/i2c.h>
> +#include <plat/omap-pm.h>
> +
> +#include <asm/mach-types.h>
> +
> +#include <media/ov5640.h>
> +#include <media/ov5650.h>
> +
> +#include "devices.h"
> +#include "../../../drivers/media/video/omap4iss/iss.h"
> +
I believe this is not good practice to include files directly from drivers
folder. You should divide the header file such that, driver specific
information stays in driver/... and platform specific goes into include/...
> +#include "control.h"
> +#include "mux.h"
> +
> +#define PANDA_GPIO_CAM_PWRDN 45
> +#define PANDA_GPIO_CAM_RESET 83
> +
> +static struct clk *panda_cam_aux_clk;
> +
> +static int panda_ov5640_power(struct v4l2_subdev *subdev, int on)
> +{
> + struct iss_device *iss = v4l2_dev_to_iss_device(subdev->v4l2_dev);
> + int ret = 0;
You are not using this variable at all, you can get rid of this.
> + struct iss_csiphy_dphy_cfg dphy;
> + struct iss_csiphy_lanes_cfg lanes;
> + unsigned int ddr_freq = 480; /* FIXME: Do an actual query for this
> */
> +
> + memset(&lanes, 0, sizeof(lanes));
> + memset(&dphy, 0, sizeof(dphy));
> +
> + lanes.clk.pos = 1;
> + lanes.clk.pol = 0;
> + lanes.data[0].pos = 2;
> + lanes.data[0].pol = 0;
> + lanes.data[1].pos = 3;
> + lanes.data[1].pol = 0;
> +
> + dphy.ths_term = ((((12500 * ddr_freq + 1000000) / 1000000) - 1) &
> 0xFF);
> + dphy.ths_settle = ((((90000 * ddr_freq + 1000000) / 1000000) + 3) &
> 0xFF);
> + dphy.tclk_term = 0;
> + dphy.tclk_miss = 1;
> + dphy.tclk_settle = 14;
> +
> + if (on) {
> + gpio_set_value(PANDA_GPIO_CAM_PWRDN, 0);
> + clk_enable(panda_cam_aux_clk);
> + mdelay(2);
> +
> + iss->platform_cb.csiphy_config(&iss->csiphy1, &dphy, &lanes);
> + } else {
> + clk_disable(panda_cam_aux_clk);
> + gpio_set_value(PANDA_GPIO_CAM_PWRDN, 1);
> + }
You may want to check return values for above API's.
> +
> + return ret;
> +}
> +
> +#define OV5640_I2C_ADDRESS (0x3C)
> +#define OV5650_I2C_ADDRESS (0x36)
> +
> +#ifdef CONFIG_MACH_OMAP4_PANDA_CAM_OV5650
> +static struct ov5650_platform_data ov_platform_data = {
> +#elif defined(CONFIG_MACH_OMAP4_PANDA_CAM_OV5640)
> +static struct ov5640_platform_data ov_platform_data = {
> +#endif
> + .s_power = panda_ov5640_power,
> +};
> +
> +static struct i2c_board_info ov_camera_i2c_device = {
> +#ifdef CONFIG_MACH_OMAP4_PANDA_CAM_OV5650
> + I2C_BOARD_INFO("ov5650", OV5650_I2C_ADDRESS),
> +#elif defined(CONFIG_MACH_OMAP4_PANDA_CAM_OV5640)
> + I2C_BOARD_INFO("ov5640", OV5640_I2C_ADDRESS),
> +#endif
> + .platform_data = &ov_platform_data,
> +};
> +
I may be wrong, but don't you think, we can clean all this #ifdefs here.
The drivers will get connected cleanly without any issues based on probing and
ID (i2c_device_id defined in driver).
Thanks,
Vaibhav
> +static struct iss_subdev_i2c_board_info ov_camera_subdevs[] = {
> + {
> + .board_info = &ov_camera_i2c_device,
> + .i2c_adapter_id = 3,
> + },
> + { NULL, 0, },
> +};
> +
> +static struct iss_v4l2_subdevs_group panda_camera_subdevs[] = {
> + {
> + .subdevs = ov_camera_subdevs,
> + .interface = ISS_INTERFACE_CSI2A_PHY1,
> + },
> + { },
> +};
> +
> +static void panda_omap4iss_set_constraints(struct iss_device *iss, bool
> enable)
> +{
> + if (!iss)
> + return;
> +
> + /* FIXME: Look for something more precise as a good throughtput
> limit */
> + omap_pm_set_min_bus_tput(iss->dev, OCP_INITIATOR_AGENT,
> + enable ? 800000 : -1);
> +}
> +
> +static struct iss_platform_data panda_iss_platform_data = {
> + .subdevs = panda_camera_subdevs,
> + .set_constraints = panda_omap4iss_set_constraints,
> +};
> +
> +
> +static struct omap_device_pad omap4iss_pads[] = {
> + {
> + .name = "csi21_dx0.csi21_dx0",
> + .enable = OMAP_MUX_MODE0 | OMAP_INPUT_EN,
> + },
> + {
> + .name = "csi21_dy0.csi21_dy0",
> + .enable = OMAP_MUX_MODE0 | OMAP_INPUT_EN,
> + },
> + {
> + .name = "csi21_dx1.csi21_dx1",
> + .enable = OMAP_MUX_MODE0 | OMAP_INPUT_EN,
> + },
> + {
> + .name = "csi21_dy1.csi21_dy1",
> + .enable = OMAP_MUX_MODE0 | OMAP_INPUT_EN,
> + },
> + {
> + .name = "csi21_dx2.csi21_dx2",
> + .enable = OMAP_MUX_MODE0 | OMAP_INPUT_EN,
> + },
> + {
> + .name = "csi21_dy2.csi21_dy2",
> + .enable = OMAP_MUX_MODE0 | OMAP_INPUT_EN,
> + },
> +};
> +
> +static struct omap_board_data omap4iss_data = {
> + .id = 1,
> + .pads = omap4iss_pads,
> + .pads_cnt = ARRAY_SIZE(omap4iss_pads),
> +};
> +
> +static int __init panda_camera_init(void)
> +{
> + if (!machine_is_omap4_panda())
> + return 0;
> +
> + panda_cam_aux_clk = clk_get(NULL, "auxclk1_ck");
> + if (IS_ERR(panda_cam_aux_clk)) {
> + printk(KERN_ERR "Unable to get auxclk1_ck\n");
> + return -ENODEV;
> + }
> +
> + if (clk_set_rate(panda_cam_aux_clk,
> + clk_round_rate(panda_cam_aux_clk, 24000000)))
> + return -EINVAL;
> +
> + /*
> + * CSI2 1(A):
> + * LANEENABLE[4:0] = 00111(0x7) - Lanes 0, 1 & 2 enabled
> + * CTRLCLKEN = 1 - Active high enable for CTRLCLK
> + * CAMMODE = 0 - DPHY mode
> + */
> + omap4_ctrl_pad_writel((omap4_ctrl_pad_readl(
> + OMAP4_CTRL_MODULE_PAD_CORE_CONTROL_CAMERA_RX) &
> + ~(OMAP4_CAMERARX_CSI21_LANEENABLE_MASK |
> + OMAP4_CAMERARX_CSI21_CAMMODE_MASK)) |
> + (0x7 << OMAP4_CAMERARX_CSI21_LANEENABLE_SHIFT) |
> + OMAP4_CAMERARX_CSI21_CTRLCLKEN_MASK,
> + OMAP4_CTRL_MODULE_PAD_CORE_CONTROL_CAMERA_RX);
> +
> + /* Select GPIO 45 */
> + omap_mux_init_gpio(PANDA_GPIO_CAM_PWRDN, OMAP_PIN_OUTPUT);
> +
> + /* Select GPIO 83 */
> + omap_mux_init_gpio(PANDA_GPIO_CAM_RESET, OMAP_PIN_OUTPUT);
> +
> + /* Init FREF_CLK1_OUT */
> + omap_mux_init_signal("fref_clk1_out", OMAP_PIN_OUTPUT);
> +
> + if (gpio_request_one(PANDA_GPIO_CAM_PWRDN, GPIOF_OUT_INIT_HIGH,
> + "CAM_PWRDN"))
> + printk(KERN_WARNING "Cannot request GPIO %d\n",
> + PANDA_GPIO_CAM_PWRDN);
> +
> + if (gpio_request_one(PANDA_GPIO_CAM_RESET, GPIOF_OUT_INIT_HIGH,
> + "CAM_RESET"))
> + printk(KERN_WARNING "Cannot request GPIO %d\n",
> + PANDA_GPIO_CAM_RESET);
> +
> + omap4_init_camera(&panda_iss_platform_data, &omap4iss_data);
> + return 0;
> +}
> +late_initcall(panda_camera_init);
> --
> 1.7.7.4
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-omap" in
> the body of a message to [email protected]
> More majordomo info at http://vger.kernel.org/majordomo-info.html
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
