Hi Devin!
On Tue August 7 2012 04:46:50 Devin Heitmueller wrote:
> This patch series contains fixes for a variety of problems found in the
> HVR-950q as well as the xc5000 driver.
>
> Details can be found in the individual patches, but it is worth mentioning
> specifically that this addresses the MythTV problem causing BUG() to occur,
> firmware loading is now significantly improved, and we now have a
> redistributable version for the xc5000c firmware.
Since you're working on the au0828 would it perhaps be possible to have that
driver use unlocked_ioctl instead of ioctl? It would be really nice if we
can get rid of the ioctl v4l2_operation at some point in the future.
Regards,
Hans
> Devin Heitmueller (24):
> au8522: fix intermittent lockup of analog video decoder
> au8522: Fix off-by-one in SNR table for QAM256
> au8522: properly recover from the au8522 delivering misaligned TS
> streams
> au0828: Make the s_reg and g_reg advanced debug calls work against
> the bridge
> xc5000: properly show quality register values
> xc5000: add support for showing the SNR and gain in the debug output
> xc5000: properly report i2c write failures
> au0828: fix race condition that causes xc5000 to not bind for digital
> au0828: make sure video standard is setup in tuner-core
> au8522: fix regression in logging introduced by separation of modules
> xc5000: don't invoke auto calibration unless we really did reset
> tuner
> au0828: prevent i2c gate from being kept open while in analog mode
> au0828: fix case where STREAMOFF being called on stopped stream
> causes BUG()
> au0828: speed up i2c clock when doing xc5000 firmware load
> au0828: remove control buffer from send_control_msg
> au0828: tune retry interval for i2c interaction
> au0828: fix possible race condition in usage of dev->ctrlmsg
> xc5000: reset device if encountering PLL lock failure
> xc5000: add support for firmware load check and init status
> au0828: tweak workaround for i2c clock stretching bug
> xc5000: show debug version fields in decimal instead of hex
> au0828: fix a couple of missed edge cases for i2c gate with analog
> au0828: make xc5000 firmware speedup apply to the xc5000c as well
> xc5000: change filename to production/redistributable xc5000c
> firmware
>
> drivers/media/common/tuners/xc5000.c | 161
> +++++++++++++++++++++-----
> drivers/media/dvb/frontends/au8522_common.c | 22 +++-
> drivers/media/dvb/frontends/au8522_decoder.c | 11 +-
> drivers/media/dvb/frontends/au8522_dig.c | 98 ++++++++--------
> drivers/media/dvb/frontends/au8522_priv.h | 29 ++++-
> drivers/media/video/au0828/au0828-cards.c | 4 +-
> drivers/media/video/au0828/au0828-core.c | 59 ++++------
> drivers/media/video/au0828/au0828-dvb.c | 54 ++++++++-
> drivers/media/video/au0828/au0828-i2c.c | 21 +++-
> drivers/media/video/au0828/au0828-reg.h | 1 +
> drivers/media/video/au0828/au0828-video.c | 76 +++++++++---
> drivers/media/video/au0828/au0828.h | 2 +
> 12 files changed, 379 insertions(+), 159 deletions(-)
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-media" in
> the body of a message to [email protected]
> More majordomo info at http://vger.kernel.org/majordomo-info.html
>
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
